Conair HC25 Manual

Conair Ikke kategoriseret HC25

Læs nedenfor 📖 manual på dansk for Conair HC25 (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

hc25_16pg021257_ib_final.indd 1 6/3/16 3:03 PM

close ccuuutttt

clipper

GOLD

Instructions for Clipper Care and Use

Model HC25

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, especially

when children are present, basic safety pre-

cautions should always be taken, including

the following:

READ ALL INSTRUCTIONS

BEFORE USING

FOR HOUSEHOLD USE ONLY

KEEP AWAY FROM WATER

DANGER

– Any appliance is

electrically live, even when the switch is off.

To reduce the risk of death or injury by

electric shock:

1. Always unplug this appliance from electri-

cal outlet immediately after using.

2. Unplug this appliance before cleaning. Unplug

the appliance when not in use.

3. Do not place or store appliance where it can

fall or be pulled into a tub or sink.

4. Do not use while bathing or in a shower.

5. Do not place in, or drop into water or other

liquids.

6. Do not reach for an appliance that has

fallen into water. Unplug immediately.

WARNING

– To reduce the risk of

burns, electric shock, fire, or injury to persons:

1. This appliance should never be left unattended

when plugged in. Do not pull, twist, or wrap line

cord around appliance.

2. This appliance should not be used by, on, or near

children or individuals with certain disabilities.

3. Use this appliance only for its intended purpose

as described in this manual. Do not use attach-

ments not recommended by the manufacturer.

Do not use an extension cord to operate this

appliance.

4. Never operate this appliance if it has a damaged

cord or plug, if it is not working properly or if it

has been dropped or damaged, or dropped into

water. Return the appliance to a service center

for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening

on this appliance.

7. Do not place appliance on any surface while it

is operating.

8. Do not use this appliance with a damaged or

broken comb or with teeth missing from the

blades as injury may occur. Before use, make

certain blades are aligned properly. (See “Care

of Your Clipper/Trimmer.”)

9. Do not use outdoors or operate where aerosol

(spray) products are being used or where oxy-

gen is being administered.

10. Never operate the appliance with the air open-

ings blocked or while on a soft surface, such

as a bed or couch, where the air openings may

be blocked. Keep the air openings free of lint,

hair, and other debris.

11. Avoid skin contact with moving blades.

12. When using the appliance with its cord,

be mindful of tangles or kinks in the cord.

If the cord does become tangled during

use, turn the unit off, unplug from outlet

and appliance, and straighten cord before

operating again.

THIS PRODUCT IS FOR

HOUSEHOLD USE ONLY

SAVE THESE

INSTRUCTIONS

USER MANUAL

Use on alternating current (120V AC 60HZ) only.

OPERATION

1. For dry location use only. Do not expose to

water.

2. When not in use, unplug unit completely.

3. Unit will become warm during operation.

TROUBLESHOOTING

If your corded trimmer does not seem to be

functioning, take the following troubleshooting

steps before returning it for repair:

1. Be sure the electrical outlet is working by

plugging in another appliance to test the outlet.

2. Make sure the electrical plug is not connected

to a switch that turns power off when lights are

turned off.

OPERATING

INSTRUCTIONS

To reduce the risk of electric shock, this appli-

ance has a polarized plug (one blade is wider

than the other). This plug will fit in a polarized

outlet only one way. If the plug does not fit fully

into the outlet, reverse the plug. If it still does not

fit, contact a qualified electrician to install the

proper outlet. Do not change the plug in any way.

Do not attempt to defeat this safety feature.

USER MAINTENANCE

INSTRUCTIONS

OILING THE BLADES

(OIL NOT INCLUDED)

About once a month you should oil the blades.

It is best to do this over a piece of newspaper.

Turn the unit on and hold it so that the blades

are pointed downward. Spread one drop of

lubricating oil across the blades, then turn the

unit off and wipe away the excess oil with a

soft cloth.

Be careful not to use too much oil and don’t oil

more than necessary, as this could damage the

motor. (Never attempt to oil the motor bearing,

as it is permanently lubricated.) After oiling the

blades, return the unit to storage. Keep oil away

from children.

BLADE CARE

Because the titanium coated blades stay sharper

longer and are precision made for a very special

use, they should always be handled with care.

Each time you finish use, take a cleaning brush

and brush away any loose hair that has collected

in the blades. Then store the unit in the storage

pouch provided to protect the blades until the

next use.

To promote the long life of the appliance, use

your trimmer only for the purpose intended by

the manufacturer.

Before you start:

1. Inspect your clipper. Make sure it’s free of

hair and dirt, is properly oiled, and running

smoothly.

2. Place a towel around the neck of the person.

3. Seat the person so that his or her head is at

your eye level. This gives you greater visibility

and control.

4. First, comb hair until it’s tangle free. Then

hold clipper in a comfortable grip. Now you’re

ready to cut.

THE CONAIR GUIDE

TO CUTTING HAIR AT HOME

MEDIUM TO LONG CUT

To begin with, cut only a small amount of hair until

you become used to the length each attachment

leaves the hair. Try the longest attachment on the

clipper first. If you want a shorter cut, you can

then use shorter combs.

• Short attachment comb (number AC404)

cuts hair to 1/16 (1.5mm)"

• Short-Medium attachment comb

(number AC405) cuts hair to 1/8 (3mm)"

• Medium-Long attachment comb

(number AC406) cuts hair to 1/4 (6mm)"

• Long attachment comb (number AC407)

cuts hair to 3/8 (9mm)"

Attach combs by holding them teeth up, then

snapping onto the bottom of the clipper blade.

To remove comb attachments, place index

finger and thumb on bottom of comb, then pull

out and up.

NOTE: Never push or shove the clipper

through the hair to make it move

more quickly. Professional experience

shows that the clipper works most

efficiently when it cuts through the

hair at its own speed.

TRIMMING

The Close Cut 10' corded clipper can also be

used as a trimming and detailing tool. Great

for touch-ups, trims and fine line detailing

between haircuts.

OUTLINING

Outlining requires no attachments. Comb

hair into the desired style. Position the clip-

per between the sideburns and the ear (see

below), making sure the corner edge of the

blade is against the hairline. With the outline

of the hair as your guide, slowly move the

clipper over, around and behind the ears.

For the back of the neck and the sideburns,

hold the clipper upside down and, holding it

against the skin at the length desired, move

the clipper downward.

STOP. COMB. CHECK.

For best results, do as the professionals do:

Comb hair often, and check clipping results

as you comb. This way you avoid uneven

sides, bangs, neckline, etc.

USE FOR TRIMMING YOUR

BEARD OR MUSTACHE

1. The clipper includes four comb attach-

ments, which provide lengths of 1/16"

(shortest) to 3/8 (longest)."

2. To use one of the attachments, press it

down over the blades until it clicks into

position. At first, until you become familiar

with the combs, use the longest comb first.

(You can always go back and make your beard

or mustache a little shorter.)

3. It is always best to begin with a clean,

slightly damp beard/mustache.

4. After you have combed through your beard/

mustache in the direction it grows naturally,

begin trimming using smooth, even strokes.

Start with your sideburns and work down-

ward toward your chin. (Never attempt to trim

against the natural growth of your beard/mus-

tache because the hair will be cut too short.)

5. If you decide you want a closer trim, you

can now switch to the shorter comb (1/16")

and go over your beard/mustache again until

you achieve the desired length.

6. After your beard/mustache has been

trimmed to the desired length, remove the

attachment comb and, using the blades only,

define the outlines of your beard/mustache.

7. Turn off the clipper and remove the attach-

ment by gently pulling up on the tab.

CARE OF YOUR CLIPPER/TRIMMER

REPLACEMENT (REMOVAL) OF BLADE SET

To remove blade set, make sure

the unit is in the OFF position.

Remove the blade set by placing

thumb against the smaller cutter

and pushing forward, releasing

the cutter assembly from the

housing. Replace with new cutting system

and reverse the removal procedure, only this

time place your thumb on the large cutter and

snap into place.

If clipper stops cutting, check to see if there is a

clump of hair lodged between the blades. If that is

the problem, unplug the clipper and then detach

the blade to remove the hair.

If the clipper stops cutting, but does not stop

running, you will need to check the blades. For

new blades, send check or money order for

$6.50, which includes postage and handling (if

$10 minimum is met) to:

Conair Corporation

150 Milford Rd.

East Windsor, NJ 08520

NOTE: Never pull on the clipper cord. Never

twist or wrap the cord around the clipper. Lay

it flat with the cord coiled up when not in use.

STORAGE

When not in use, your clipper should be dis-

connected, allowed to cool and stored in a

safe, dry location, out of reach of children.

Any other servicing should be performed by

an authorized service representative. This

appliance has no user-serviceable parts. The

product is for household use.

WARNING:

IF YOU THINK

THE POWER IS OFF

WHEN THE SWITCH

IS OFF,

YOU’RE WRONG.

KEEP AWAY FROM WATER

Everyone knows that electricity and water

are a dangerous combination. But did you

know that an electric appliance is still electri-

cally live even if the switch is off? If the plug

is in, the power is on. So when you are not

using your appliances, keep them unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES

LIMITED TWO-YEAR WARRANTY

(U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your

unit free of charge for 24 months from the

date of purchase if the appliance is defective in

workmanship or materials.

To obtain service under this warranty, return the

defective product to the service center listed

on back, together with your purchase receipt

and $3.00 for postage and handling. California

residents need only provide proof of purchase

and should call 1-800-3-CONAIR for shipping

instructions. In the absence of a purchase receipt,

the warranty period shall be 24 months from the

date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS,

OR LIABILITIES, INCLUDING BUT NOT

LIMITED TO THE IMPLIED WARRANTY OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL BE LIMITED IN

DURATION TO THE 24-MONTH DURATION OF

THIS WRITTEN, LIMITED WARRANTY. Some

states do not allow limitations on how long an

implied warranty lasts, so the above limitations

may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES FOR BREACH OF

THIS OR ANY OTHER WARRANTY, EXPRESS

OR IMPLIED, WHATSOEVER. Some states do

not allow the exclusion or limitation of special,

incidental, or consequential damages, so the

above limitation may not apply to you.

This warranty gives you specific legal rights, and

you may also have other rights, which vary from

state to state.

Please register this product at

www.conair.com/registration

Service Center

Conair Corporation

Service Department

7475 North Glen Harbor Blvd.

Glendale, AZ 85307

150 Milford Road, East Windsor, NJ 08520

7475 North Glen Harbor Blvd., Glendale, AZ 85307

16PG021257 IB-14377

CUT HERE

CLIPPER REPLACEMENT PARTS & ACCESSORIES ORDER FORM

Pricing in effect through December 31, 2018. Orders postmarked after this date will be accepted, and the customer will be notified if pricing has changed.

Attachment Comb 1/16" $3.00AC404

Attachment Comb 1/8" $3.00AC405

Attachment Comb 1/4" $3.00AC406

Attachment Comb 3/8" $3.00AC407

Lubricating Oil $2.00HC-OIL

T-Blade $6.50BLD-166

ITEM PART # PRICE QUANTITY AMOUNT

Subtotal

*Sales Tax

TOTAL

Enclose check or money order made payable to Conair. (We cannot accept cash, stamps

or C.O.D. orders.) *CT, IL, AZ, and PA residents should add applicable state sales tax.