Conair HC318RVW Manual


Læs nedenfor 📖 manual på dansk for Conair HC318RVW (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 12 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
22 PI EC E C OR D/C ORD LESS HA IR CUT K I T
[rechargeable]
Fig 1
Fig 2
Instructions for Care and Use
MODEL HC318R
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, take basic safety
precautions, including the following:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY FROM WATER
DANGER any appliance is electrically
live, even when the switch is off.
To reduce the risk of death or injury by electric
shock:
1. Unplug this appliance before cleaning.
2. Do not place or store appliance where it can fall
or be pulled into a tub or sink.
3. Do not use while bathing or in a shower.
4. Do not place in, or drop into water or other liquid.
5. Do not reach for an appliance that has fallen into
water. Unplug immediately.
6. Except when charging, always unplug this
appliance from electrical outlet immediately
after using.
DO NOT REACH
INTO THE WATER
WARNING To reduce the risk of burns,
electric shock, fire, or injury to persons:
1. This appliance should never be left unat-
tended when plugged in. Do not pull, twist,
or wrap line cord around appliance.
2. This appliance should not be used by, on, or near
children or individuals with certain disabilities.
3. Use this appliance only for its intended purpose
as described in this manual. Do not use attach-
ments not recommended by the manufacturer.
Do not use an extension cord to operate this
appliance.
4. Never operate this appliance if it has a
damaged cord or plug, or if it is not work-
ing properly, if it has been dropped or
damaged, or dropped into water. Return
the appliance to a service center for
examination and repair.
5. Keep the cord away from heated surfaces.
6. Never drop or insert any object into any open-
ing on this appliance.
7. Do not place appliance on any surface while
it is operating.
8. Do not use this appliance with a damaged or
broken comb or with teeth missing from the
blades as injury may occur. Before use, make
certain blades are aligned properly. (See
“Care of your Clippers”)
9. Do not use outdoors or operate where aerosol
(spray) products are being used or where
oxygen is being administered.
10. Never operate the appliance with the air
openings blocks or while on a soft surface,
such as a bed or couch, where the air open-
ings may be blocked. Keep the air openings
free of lint, hair, and the like.
11. Always attach plug to appliance first, then
to outlet. To disconnect, turn all controls to
“OFF” then remove plug from outlet.
12. Avoid skin contact with moving blades.
13. When using the appliance with its cord,
be mindful of tangles or kinks in the cord.
If the cord does become tangled during use,
turn the unit off and straighten cord before
operating again.
14. Keep lubricating oil out of reach of children.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
FOR RECHARGEABLE APPLICATION
Your new Conair Haircut Kit has everything you need
to achieve professional haircuts at home. Its power-
ful D.C. motor clipper with Stainless Steel blades for
long lasting cutting precision, features a new 5-posi-
tion adjustamatic taper control. What ever hair length
you set the lever for, the clipper will automatically cut
all hair in that section at the same desired length.
Also included are 10 attachment combs for differ-
ent hair lengths, barber scissors, a styling comb
with angled teeth, a barber comb with straight
teeth, a full length barber cape, a neck brush, a
hard case for easy storage, and 2 styling clips
to assist you in cutting longer hair styles. It also
comes with lubricating oil, a cleaning brush and
a blade guard for easy maintenance of the clip-
per blades.
This appliance is intended for household use. Comes
with an adapter used on 100-240V AC 50/60 HZ.
1. Before using the clipper for the first time,
charge continuously for 16 hours. Maximum
battery capacity will only be reached after
3 charging and discharging cycles.
2. After use, turn the switch to “Off position.
Recharge batteries by connecting the charg-
ing jack into the receptacle at the end of the
clipper and plugging the adapter unit into
the electrical outlet. The charging indicator
lamp will light up to indicate that charging
has begun.
3. After recharging, store in a dry place, away
from small children.
4. Do not wrap cord around the clipper.
5. Preserving the batteries: in order to maintain
the optimum capacity of the rechargeable bat-
teries, the clipper should be recharged for 16
hours approximately every 3 months.
FOR DIRECT PLUG-IN OPERATION
1. Connect the charging jack into the receptacle
at the end of the clipper.
2. Plug the adapter unit into the electric outlet.
3. Turn the switch to “Offposition, let the clipper
charge for a few minutes first.
4. Turn the switch to “On” position.
5. Unplug the adapter unit after use.
6. After use, store in a dry place away from small
children.
7. Do not wrap cord around the clipper.
8. This power unit is intended to be correctly
oriented in a vertical or floor mount position.
CONTAINS NICKEL-
CADMIUM BATTERY.
MUST BE COLLECTED,
RECYCLED OR DISPOSED
OF PROPERLY. DO NOT
DISPOSE OF IN
MUNICIPAL WASTE.
BATTERY REMOVAL INSTRUCTIONS
1. Using a small Phillips screwdriver, remove the
screw on the bottom housing at back of the
clipper.
2. Remove the top housing by hand.
3. Now the battery is exposed so you can separate
the wire connectors. Carefully hold the wires on
each side of the connector and gently cut the
wires. The connector will separate and the bat-
teries can be removed from the inner housing.
Bring the battery to the nearest collection center
for disposal or call the toll-free RBRC informa-
tion line at 1-800-8-BATTERY. RBRC is a trade-
mark of The Rechargeable Battery Recycling
Corporation. DO NOT throw the batteries into the
normal municipal waste system.
Never use cord to pull clipper. Never twist or
otherwise obstruct cord. To store, coil cord loosely
and secure with a twist tie.
THE CONAIR GUIDE
TO CUTTING HAIR AT HOME
Before you start:
1. Inspect your clipper to make sure it is free
of hair and dirt, is properly oiled and is running
smoothly.
2. Place a towel or cape around the neck of the
person getting the haircut.
3. Sea t the person so that his/her head is at your eye
level. This gives you greater visibility and control.
4. Comb hair until it is tangle-free. Hold the clipper in
a comfortable grip. Now you’re ready to cut
MEDIUM TO LONG CUT
To begin, cut only a small amount of hair until
you become used to the length each attachment
leaves the hair. Try the longest attachment on the
clipper first. If you want a shorter cut, you can then
use shorter combs.
• Short attachment comb (number 1)
cuts hair to 1/8".
• Medium-Short attachment comb (number 2)
cuts hair to 1/4".
• Medium-Long attachment comb (number 3)
cuts hair to 3/8".
• Long attachment comb (number 4)
cuts hair to 1/2".
• Long attachment comb (number 5)
cuts hair to 5/8".
• Long attachment comb (number 6)
cuts hair to 3/4".
• Long attachment comb (number 7)
cuts hair to 7/8".
• Long attachment comb (number 8)
cuts hair to 1"
• Left ear attachment comb lightly tapers over
left ear.
Right ear attachment comb lightly tapers over
right ear.
Attach combs by holding them teeth up then
snapping onto the bottom of the clipper blade.
NOTE: Never push
or shove the clipper
through the hair to
make it move more
quickly. Pro fes sional
experience shows
that the clipper
works most effi-
ciently when it cuts
through the hair at
its own speed.
To remove comb
attachments, place
index finger and
thumb as illustrated;
then pull out and up.
To begin cutting hair:
1. The hair should be combed
in its natural direction.
2. Using the largest
at tachment comb, trim
sides from the bottom
upwards. Hold clipper lightly
against the hair with teeth
of the attachment comb
pointing upward, yet flat
against the head. Gradually
lift the clipper upward and
outward through the hair,
trimming just a little at a
time. Re peat around sides
and back of head.
3. If you want hair to be
even shorter: Apply more
pressure to the head with
the attachment comb that
is in place. This takes a
little practice, of course.
Or, just switch to a
shorter attachment comb.
Remember, it’s better to
leave too much hair than
too little.
For longer hair on top, use
the barber comb and lift
hair on the top of the head,
cutting over the comb, or
hold hair between fingers
and cut to desired length.
Always working from the
front to the back of the
head, gradually cut the
hair shorter by reducing the space between
the comb or fingers and the head. Comb often
to check for uneven strands, and to get rid of
trimmed hair. For thicker hair and more cutting
power, press the turbo button on the side.
OUTLINING
Outlining requires no attachments. Comb the
hair into the desired style, Position the clip-
per between the sideburns and the ear (see
sketch) and make sure the corner edge of the
blade is against the hairline. With the outline of
the hair as your guide, slowly move the clip-
per over, around and behind the ears. For the
back of the neck and the sideburns, hold the
clipper upside down (see sketch) and, holding
it against the skin at the length desired, move
the clipper downward.
STOP. COMB. CHECK.
For best results, do as the professionals do:
comb the hair often and check results as you
comb. This way you can avoid uneven sides,
bangs, neckline, etc.
SHORTCUTS TO PERFECT
FLAT TOPS, CREW CUTS, ETC.
Always cut the hair from the back of the
neck toward the crown, using the longest
comb setting. Hold the comb attachment flat
against the head and slowly move the clipper
up through the hair. Use the same technique
for the sides, cutting from the bottom to the
upper side of the head.
For the front of the crown, cut the hair against
its natural direction. Then even it up with the
sides.
For a flat top use a flat comb, not the attach-
ment comb. Just cut top hair by running the
clipper over the comb.
To taper hair down to the neckline, use the lower
settings attachment comb. Comb the hair and
check for uneven spots. Outline the sideburns
and neckline areas (see Outlining).
USER-MAINTENANCE
INSTRUCTIONS
CARE OF YOUR CLIPPERS
DETACHABLE BLADE SET
Your clipper is equipped with a detachable
blade set for routine maintenance, cleaning and
replacement.
To remove the blade: the
front of the clipper should
be facing you, push up
under the blade with your
thumb and the blade will
pop-out. (See Fig 1)
To replace the blade: Make
sure the taper control is set
to the longest position and
with the back of the clip-
per facing you, insert the
bottom side (with screws)
of the blade into the clip-
per and push down until it snaps into place.
(See Fig 2)
MAINTENANCE OF THE BLADE
Always apply oil to the blades before, during
and after use. This will ensure maximum cut-
ting performance. Hold clipper away from your
body in a downward position and apply oil on
the front and sides of the cutter blade. Wipe
excess oil off with a soft, dry cloth.
SPECIAL OIL
To maintain the blades of your Conair
® clipper
in peak condition, oil them after every three or
four haircuts. Gently place a few drops of oil on
the teeth of the blades, using the special Conair
oil included with your set. Turn the clipper on
for a minute, then turn off. This light, natural
oil was formulated specifically for the Conair®
high-speed clipper. Be cause it is the right oil
to use, it will not slow down the blades. Never
use any other product; there is no substitute for
Conair oil.
5 DETENT TAPER CONTROL
Just like levers on professional clippers, the Conair
taper lever is positioned at your thumb so you can
hold the clipper in your hand and adjust the lever
at the same time... while you’re clipping. This taper
lever eliminates the need in some situations for
an attachment comb because it lets you gradually
adjust the closeness of the cut. For the closest cut
and the shortest hair, push taper lever up as far
as it will go to level #1. To increase cutting length,
slowly push lever down. If you push to the lowest
position level #5, it will leave hair about the same
length as the short
attachment comb.
Close Cut
Longer
Cut
Because a different cutting edge is used in
each setting, the taper lever lengthens the
life of your blades. Packed-in hair can slow
down any clipper. To remove it, without
removing the blades. Take your cleaning brush
and brush the hair from the blades. If you do
this after every clipping, especially with heavy
hair cutting, the blades should remain free of
cut hair. If clipper stops cutting and this action
doesn’t help, you might have to loosen the
blades to remove the hair.
For new blades, send check or money order for
$6.50 (which includes postage and handling) to:
Conair Corporation
150 Milford Rd.
East Windsor, NJ 08520
NOTE: Never pull on the clipper cord.
Never twist or wrap the cord around the
clipper; lay it flat with the cord coiled up
when not in use.
Bottom
Blade
Top
Blade
Adjustable
Taper
Lever
On/Off
Switch
Charging
light
Detachable
Blade Set WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU'RE WRONG.
KEEP AWAY FROM WATER
Everyone knows that electricity and water are
a dangerous combination. But did you know
that an electric appliance is still electrically
alive even if the switch is off? If the plug is in
the power is on. So when you are not using
your appliances, keep them unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
LIMITED FIVE YEAR WARRANTY
Conair will repair or replace (at our option) your
unit free of charge for 60 months from the date
of purchase if the appliance is defective in
workmanship or materials.
To obtain service under this warranty, return the defec-
tive product to the service center listed below together
with your purchase receipt and $3.00 for postage and
handling. California residents need only provide proof of
purchase and should call 1-800-366-0937 for shipping
instructions. In the absence of a purchase receipt, the
warranty period shall be 60 months from the date of
manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTY OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED IN DURATION TO
THE 60 MONTH DURATION OF THIS WRITTEN,
LIMITED WARRANTY. Some states do not allow
limitations on how long an implied warranty lasts,
so the above limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, OR CONSEQUEN-
TIAL DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. Some states do not allow the
exclusion or limitation of special, incidental, or
consequential damages, so the above limitation
may not apply to you.
This warranty gives you specific legal rights, and
you may also have other rights, which vary from
state to state.
Once again, thanks for buying a
Conair product.
Your Conair® clipper blades are made of high
carbon stainless steel. They are engineered
for precise, professional results. If blades feel
like they are pulling or grabbing hair, it means
they are losing their sharpness and should be
replaced as soon as possible.
Attachment combs should also be replaced if
they are lost or broken. It is easier to cut hair with
the accuracy of a pro when the necessary tools
are at your fingertips.
Conair makes a variety of accessories for dif-
ferent haircut kits. If your haircut kit does not
include them, you may want to consider adding
them to your professional haircutting tools.
Left and right ear attachment combs provide
effortless, precise cutting around the ears. Styling
clips hold hair in place when you are sectioning
hair. A styling comb makes it easy to taper or cut
hair at an angle. A barber cape ensures a comfort-
able and neat haircut and a convenient storage
pouch keeps all your essentials in one place.
To register your Conair product please simply go
to www.conair.com/registration and the site will
guide you to register your item.
©2010 Conair Corporation
Service Center
Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
10PG112818 IB-9906
EXCITING NEW ITEMS
FROM CONAIR
The first cordless,
rechargeable
angled shaving head with
an universal grip, 3-position
taper control, 3 attachment
combs and trimmer
attachment.
Model HG300
Corded beard and
mustache trimmer with
5-position adjustable comb
and 2 jawline detailing
combs.
Model GMT8CS
Model COMB-10
Model COMB-11
Model COMB-13
Model HCNB-1
Model CAPE-1
Model HC OIL
Model HC VIDEO
Model SC-1
Model BLD-7
Model HC-1
Model CLP-1
Model DVD-1
Model COMB-12
CUT HERE
HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM
Pricing in effect through June 1, 2011. Orders postmarked after this date will be accepted, and the customer will be notified if pricing has changed.
Subtotal
*Sales Tax
TOTAL
Enclose check or money order made payable to Conair. (We cannot accept cash, stamps or C.O.D. orders.) CT, IL, AZ, and PA residents
should add applicable state sales tax. Minimum order of $10.00 or a $2.00 handling charge will be added to order.
All prices include handling and return postage. Prices are subject to change without notice.
Prices are valid only for shipments within the Continental United States. Please allow 4-6 weeks for delivery.
To avoid delays, please print clearly.
We must have a street address, as UPS cannot deliver to a P.O. box.
NAME ________________________________________________________________________________
AddrEss __________________________________ Apt. ____________________________________
CItY ______________________________________ stAtE _______ ZIp _______________________
tELEpHONE ( ) __________________________________________________
(We call only if we have a question about your order.)
For information on other Conair® haircut kit parts call: 1-800-3-CONAIR.
Mail to:
Conair Corporation
Service Department
150 Milford Road
East Windsor,
NJ 08520-9730
Set of 4 Attachment Combs: 1/8", 1/4", 3/8", 1/2". Fits all clippers COMB-10 $5.00
Set of 2 Attachment Combs: left ear and right ear. Fits all clippers COMB-11 $1.75
1" Comb fits all clippers COMB-12 $1.75
3 attachment combs: 5/8", 3/4", 7/8". Fits all clippers $5.00COMB-13
Neck Brush HCNB-1 $1.50
Deluxe White Vinyl Cape with Velcro Collar CAPE-1 $5.00
Lubricating Oil (pkg. of 3 tubes) HC OIL $2.00
Approximate 28 Minute haircut video in Spanish & English (Optional) $8.95HC VIDEO
Instructional DVD DVD-1 $5.00
Barber Scissors $2.00SC-1
Blade Set for HC318 BLD-7 $6.50
Blade Guard $1.00HC-1
Styling Clips (set of 3) CLP-1 $1.50
ITEM PART # PRICE QUANTITY AMOUNT


Produkt Specifikationer

Mærke: Conair
Kategori: Ikke kategoriseret
Model: HC318RVW

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair HC318RVW stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Conair Manualer

Conair

Conair NPTCCA01 Manual

10 December 2024
Conair

Conair NPTCCA02 Manual

10 December 2024
Conair

Conair MASK2 Manual

1 Oktober 2024
Conair

Conair skn SFB11GK Manual

1 Oktober 2024
Conair

Conair Man GMTL6000 Manual

6 September 2024
Conair

Conair LNT1 Manual

6 September 2024
Conair

Conair Man GMT189R Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024