Conair HC408R Manual

Conair Ikke kategoriseret HC408R

Læs nedenfor 📖 manual på dansk for Conair HC408R (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

2 0 P I E C E H A I R C U T K I T

Instructions for Care and Use

MODEL HC408

MPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, especially

when children are present, basic safety

precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS

BEFORE USING

KEEP AWAY FROM WATER

DANGER — any appliance is electrically

live, even when the switch is off.

To reduce the risk of electric shock:

1. Do not reach for an appliance that has

fallen into water. Unplug immediately.

2. Do not use while bathing or in the shower.

3. Do not place or store appliance where it can

fall or be pulled into a tub or sink. Do not place

in or drop into water or other liquids.

4. Always unplug this appliance from the

electrical outlet immediately after using.

5. Unplug this appliance before cleaning.

DO NOT REACH

INTO THE WATER

WARNING— Toreducetheriskofburns,

electric shock, fire, or injury to persons:

1. This appliance should never be left unat-

tended when plugged in.

2. This appliance should not be used by, on,

or near children or by individuals with certain

disabilities.

3. Use this appliance only for its intended

use as described in this manual. Do not

use attachments not recommended by the

manufacturer.

4. Never operate this appliance if it has a

damaged cord or plug, if it is not working

properly, if it has been dropped, dam-

aged, or dropped into water. Return the

appliance to an Authorized Service Center

for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never operate the appliance with the air

opening blocked or while on a soft surface,

such as a bed or couch, where the air

openings may be blocked. Keep the air open-

ings free of lint, hair and the like.

7. Never drop or insert any object into any

opening.

8. Do not use outdoors or operate where

aerosol (spray) products are being used or

where oxygen is being administered.

9. To disconnect, turn all controls to OFF, then

remove plug from outlet.

10. Do not place appliance on any surface

while it is operating.

11. Do not use this appliance with a

damaged or broken comb or with teeth miss-

ing from the blades, as injury may occur.

12. Avoid skin contact with moving blades.

13. If the cord becomes tangled during use,

turn the unit off and straighten cord before

operating again.

SAVE THESE

INSTRUCTIONS

OPERATING

INSTRUCTIONS

This appliance is used on Alternating Current

120V (AC 60 hertz) only.

To reduce the risk of electric shock, this

appliance has a polarized plug (one blade is

wider than the other). As a safety feature, this

plug will fit in the outlet only one way. If the

plug does not fit fully in the outlet, reverse

the plug. If it still does not fit, contact a

qualified electrician to install the proper out-

let. Do not change the plug in any way.

Your new Conair® haircut kit has everything

you need to achieve professional haircuts at

home. It features a powerful clipper with cut-

ting precision. Also included are 8 number-

coded comb attachments for different hair

lengths (including left and right ear combs). It

also comes with 2 styling clips to assist you in

cutting longer hair styles, a storage case, bar-

ber comb, barber scissors, barber cape, clean-

ing brush, lubricating oil and a blade guard for

easy maintenance of the clipper blades.

THE CONAIR GUIDE

TO CUTTING HAIR AT HOME

Before you start:

1. Inspect your clipper. Make sure it’s free

of hair and dirt, properly oiled, and running

smoothly.

2. Place a towel or cape around the neck of

the person whose hair is being cut.

3. Seat the person so that his or her head is at

your eye level. This gives you greater visibility

and control.

4. First, comb hair until it’s tangle-free. Then

hold clipper in a comfortable grip. Now you’re

ready to cut.

Please note your [number] cut™ 20-piece

haircut kit comes with easy-to-use

number-coded combs, so you can easily

remember your favorite comb once you

start to use the kit on a regular basis.

MEDIUM TO LONG CUT

To begin with, cut only a small amount of

hair until you become used to the length each

attachment leaves the hair. Try the longest

attachment on the clipper first. If you want a

shorter cut, you can then use shorter combs.

• Short attachment comb (number 1) cuts

hair to 1/8".

• Medium-Short attachment comb (number 2)

cuts hair to 1/4".

• Medium-Long attachment comb (number 3)

cuts hair to 3/8".

• Long attachment comb (number 4) cuts

hair to 1/2".

• Long attachment comb (number 5) cuts

hair to 5/8".

• Long attachment comb (number 6) cuts

hair to 3/4".

• Long attachment comb (number 7) cuts

hair to 7/8".

• Long attachment comb (number 8) cuts

hair to 1".

• Left ear attachment comb lightly tapers

over left ear.

• Right ear attachment comb lightly tapers

over right ear.

Attach combs by hold-

ing them teeth up,

then snapping onto the

bottom of the clipper

blade.

To remove comb

attachments, place

index finger and thumb

as illustrated; then pull

out and up.

NOTE: Never push or shove the clipper

through the hair to make it move more

quickly. Professional experience shows that

the clipper works most efficiently when it

cuts through the hair at its own speed.

To begin cutting hair:

1. The hair should be

combed in its natural

direction.

2. Using the largest

attachment comb, trim

sides from the bottom

upwards. Hold clipper lightly against the hair

with teeth of the attachment comb pointing

up ward, yet flat against the head. Gradually lift

the clipper upward and outward through the

hair, trimming just a little at a time.

Repeat around sides and

back of head.

If you want hair to be even

shorter:

A) Apply more pressure to

the head with the attach-

ment comb that is in place.

This takes a little practice,

of course.

B) Just switch to a shorter

attachment comb.

Remember, it’s better to

leave too much hair than too

little. For longer hair on top,

use the barber comb and lift

hair on the top of the head,

cutting over the comb. Or,

hold the hair between the

fingers and cut to desired

length. Always working from

the front to the back of the head, gradually cut

the hair shorter by reducing the space between

the comb or fingers and the head. Comb often

to check for uneven strands, and to get rid of

trimmed hair.

OUTLINING:

Outlining requires no attachments. Comb

hair into the desired style. Position the clip-

per between the sideburns and the ear (see

above), making sure the corner edge of the

blade is against the hairline. With the outline of

the hair as your guide, slowly move the clipper

over, around and behind the ears. For the back

of the neck and the sideburns, hold the clipper

upside down (see Fig. 1) and, holding it against

the skin at the length desired, move the clipper

downward.

Fig. 1

STOP. COMB CHECK.

For best results, do as the professionals do:

comb hair often, and check clipping results as

you comb. This way you avoid uneven sides,

bangs, neckline, etc.

SHORT CUTS TO PERFECT

FLAT TOPS, CREW CUTS, ETC.

Always cut from the back of the neck to the

crown, using the longest comb setting. Hold

the comb attachment flat against the head

and slowly move the clipper up through the

hair. Use the same technique for the sides,

cutting from the bottom to the upper side of

the head.

For the front to the crown, cut the hair against

the direction in which it grows. Then even it

up with the sides.

For a flat top, use the flat comb, not the

attachment comb. Just cut hair on top of the

head over the flat comb (see Fig. 2).

Fig. 2

To taper hair down to the neckline, use

attachment comb #1. Comb hair and

check for uneven spots. Outline sideburns

and neck areas (see “Outlining”).

USER-MAINTENANCE

INSTRUCTIONS

CARE OF YOUR CLIPPERS

MAINTENANCE OF THE BLADE

Always apply oil to the blades before, during and

after use. This will ensure maximum cutting

performance. Hold clipper away from your body

in a downward position and apply oil on the front

and sides of the cutter blade. Wipe excess oil off

with a soft dry cloth.

Conair® hair clippers are carefully inspected to

insure that the blades are in perfect alignment.

You will need to realign the blades if they

should be knocked out of alignment. How can

you tell if the blades need realigning? Simply

match them up, point for point, to conform with

the drawing below.

To replace cutting comb and cutter after remov-

al for cleaning, replacement or because they

are out of alignment, slide the cutter back onto

the black plastic oscillating head. Next, you

must make sure that the cutter (small blade)

and the cutting comb (large blade) are properly

aligned. Line up the new or existing cutting

comb with the two screw holes. Place the

original screws, one in each hole, and lightly

tighten with a Phillips head screwdriver.

Fig. 3

Large blade (cutting comb)

Blade screws

Small blade (cutter)

Then, match the two blades up, point to point,

conforming with the illustration below in Fig. 4.

Fig. 4 1/32" to 1/16"

Cutting Comb (large blade)

Cutter

(small blade)

*The top edge of the cutting comb should be

1/32" to 1/16" (.79 mm. to 1.59 mm.) higher

than the top edge of the cutter. This is important

so that the clipper does not cut too close or

come in contact with the skin.

*The extreme left tooth of the cutting comb

must cover or be to the extreme left of the first

small tooth of the cutter.

*Be sure that the extreme right big tooth of the

cutter touches the extreme right tooth of the

cutting comb.

Any other servicing should be performed by an

authorized service representative or that the

appliance has no user-serviceable parts. The

product is for household use.

Do not pull, twist, or wrap line cord around

appliance.

SPECIAL OIL

To maintain the blades of your Conair®

clipper, always apply oil to the blades before,

during and after use. Gently place a few

drops of oil on the teeth of the blades, using

the special Conair® oil included with your

set. Turn the clipper on for a minute, then

turn off. This light, natural oil was formu-

lated specifically for the Conair® high-speed

clipper. Be cause it is the right oil to use, it

will not slow down the blades. Never use

any other product. There is no substitute for

Conair oil.

POWER SCREW

The power screw permits you to adjust power

to your clipper. You may need to make this

adjustment if the power in your house is low.

(The Conair

clipper was designed for house-

hold use.)

1. With a screwdriver or a dime, turn the power

screw counterclockwise until the arm strikes a

coil, making a clacking noise ( .1). Fig

Fig. 1

2. Turn the screw clockwise until the noise stops,

and then turn about 45 degrees more. This is

the maximum power setting (Fig. 2).

Fig. 2

ADJUSTABLE TAPER LEVER

Just like professional clippers, the Conair taper

lever is positioned at your thumb. You can hold

the clipper in your hand and adjust the lever at

the same time...while you’re clipping.

This taper lever eliminates the need for

an attachment comb because it lets you

gradually adjust the closeness of the cut. For

the closest cut and the shortest hair, push taper

lever up as far as it will go. To increase cutting

length, slowly push lever down. If you push to

the lowest position, it will leave hair about the

same length as the short attachment.

Because a different cutting edge is used in

each setting, the taper lever lengthens the life

of your blades.

Packed-in hair can slow down any clipper. To

remove hair without removing the blades, use

your cleaning brush to brush hair out of the

blades. This should be done after each use.

When blades are free of hair, apply a small

amount of oil across them.

Close Cut

Longer Cut

If you do this after every clipping, especially

with heavy hair cutting, the blades should

remain in good working condition. If clipper

stops cutting and this action doesn’t help,

check the blades. If they’ve become dull,

replace them. For new blades, send check

or money order for $6.50 (see order blank.)

This price includes postage and handling, but

$10.00 minimum must be met.

Conair Corporation

150 Milford Rd.

East Windsor, NJ 08520

CAUTION: Never pull on the clipper cord.

Never twist or wrap the cord around the clip-

per. Lay it flat with the cord coiled up when

not in use.

Blade

Top

Bottom

Blade

Power

Screw

Adjustable

Taper Lever

ON/OFF

Switch

WARNING:

IF YOU THINK

THE POWER IS OFF

WHEN THE SWITCH

IS OFF,

YOU'RE WRONG.

KEEP AWAY FROM WATER

Everyone knows that electricity and water

are a dangerous combination. But did you

know that an electric appliance is still

electrically alive even if the switch is off? If

the plug is in, the power is on. So when you

are not using your appliances, keep them

unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES

LIMITED FIVE YEAR WARRANTY

Conair will repair or replace (at our option) your unit

free of charge for 60 months from the date of purchase

if the appliance is defective in workmanship

or materials.

To obtain service under this warranty, return the

defective product to the service center listed below,

together with your purchase receipt and $3.00 for

postage and handling. California residents need only

provide proof of purchase and should call 1-800-366-

0937 for shipping instructions. In the absence of a

purchase receipt, the warranty period shall be 60

months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR

LIABILITIES, INCLUDING BUT NOT LIMITED TO THE

IMPLIED WARRANTY OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, SHALL BE

LIMITED IN DURATION TO THE 60-MONTH DURATION

OF THIS WRITTEN, LIMITED WARRANTY. Some

states do not allow limitations on how long an implied

warranty lasts, so the above limitations may not apply

to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES FOR BREACH OF THIS OR ANY OTHER

WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.

Some states do not allow the exclusion or limitation of

special, incidental, or consequential damages, so the

above limitation may not apply to you.

This warranty gives you specific legal rights, and you

may also have other rights, which vary from state to

state.

SERVICE CENTER

CONAIR CORPORATION

Service Department

7475 North Glen Harbor Blvd.

Glendale, AZ 85307

10PG112364 IB-9855

Once again, thanks for buying a

Conair product.

Your Conair® clipper blades are made of high

carbon stainless steel. They are engineered

for precise, professional results. If blades feel

like they are pulling or grabbing hair, it means

they are losing their sharpness and should be

replaced as soon as possible.

Attachment combs should also be replaced

if they are lost or broken. It is easier to cut

hair with the accuracy of a pro when the

necessary tools are at your fingertips.

Conair makes a variety of accessories

for different haircut kits. If your haircut kit does

not include them, you may want to consider

adding them to your professional haircutting

tools.

Left and right ear attachment combs

provide effortless, precise cutting around the ears.

Styling clips hold hair in place when you are sec-

tioning hair. A styling comb makes it easy to taper

or cut hair at an angle. A barber cape ensures a

comfortable and neat haircut and a convenient

storage pouch keeps all your essentials in one

place.

Last but not least, an easy-to-follow

30-minute “Haircuts at Home” video is

available. It demonstrates basic haircut-

ting techniques and follows four popular

haircuts step by step. It will give you the

confidence and instruction you need to give.

great-looking haircuts to every member of

your family.

To register your Conair product, please simply

go to www.conair.com/registration and the site

will guide you.

EXCITING ITEMS

FROM CONAIR

PT1 Mighty Mini 15-Piece Clipper Kit

Powerful DC motor

makes this unique,

lightweight clipper /

trimmer a versatile cut-

ting instrument, as it

can also be used for

detailing and bikini line

trimming.

GMT189CGB 13-Piece Trimmer

Rechargeable

Beard & Mustache

trimmer with stainless

steel blades and a

5-position attachment

comb for a blended

and tapered trim.

Model Comb-408 Model CLP- 1 Model HC VIDEO

Model Comb-408 Model SC- 1 Model BLD-8

Model HCNB-1 Model Comb-408 Model HC OIL

Model HC- 1 Model CAPE-1 Model Comb-408

HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM

Pricing in effect through June 1, 2011. Orders postmarked after this date

will be accepted, and the customer will be notified if pricing has changed.

CUT HERE

ITEM PART # PRICE QUANTITY AMOUNT

Blade Set for HC408 BLD-8 $6.50

Set of 4 Attachment Combs:1/8", 1/4", 3/8", 1/2". COMB-408 $5.00

Set of 2 Attachment Combs: left ear and right ear. COMB-408 $1.75

1" Comb COMB-408 $1.75

3 attachment combs 5/8", 3/4", 7/8". COMB-408 $5.00

Neck Brush HCNB-1 $1.50

Deluxe Black Vinyl Cape with Velcro Collar CAPE-1 $5.00

Lubricating Oil (pkg. of 3 tubes) HC OIL $2.00

30 Minute Haircut Video HC VIDEO $8.95

Barber Scissors SC-1 $2.00

Blade Guard HC-1 $1.00

Styling Clips (set of 3) CLP-1 $1.50

Enclose check or money order made payable to Conair. (We cannot accept cash, stamps or C.O.D. orders.) *CT, IL, AZ,

and PA residents should add applicable state sales tax. Minimum order of $10.00 or a $2.00 handling charge will be Subtotal

added to order. All prices include handling and return postage. Prices are subject to change without notice. Prices

are valid only for shipments within the continental United States. Please allow 4–6 weeks for delivery. To avoid *Sales Tax

delays, please print clearly. We must have a street address, as UPS cannot deliver to a P.O. box.

TOTAL

NAME_____________________________________________________________________________________

ADDRESS__________________________________________________________ ____________________ APT. Mail to:

Conair Corporation

CITY___________________________________________________________ ____________STATE ZIP________ Service Department

150 Milford Road

TELEPHONE ( ) _ __________________________________ (We call only if we have a question about your order.) East Windsor, NJ 08520-9730

For information on other Conair ® haircut kit parts, call: 1-800-3-CONAIR.

Produkt Specifikationer

Mærke:	Conair
Kategori:	Ikke kategoriseret
Model:	HC408R

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair HC408R stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Conair Manualer

Conair NPTCCA01 Manual

10 December 2024

Conair True Glow PB8NPRF Manual

10 December 2024

Conair NPTCCA02 Manual

10 December 2024

Conair MiniPRO CS80N Manual

1 Oktober 2024

Conair MASK2 Manual

1 Oktober 2024

Conair skn SFB11GK Manual

1 Oktober 2024

Conair Man GMTL6000 Manual

6 September 2024

Conair LNT1 Manual

6 September 2024

Conair Man GMT189R Manual

6 September 2024

Conair InfinitiPRO 998 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg KIT6PX Manual

23 December 2024

Smeg KIT6CX Manual

23 December 2024

Smeg GTA-6 Manual

23 December 2024

Lucide Casper i 79166/19/12 Manual

23 December 2024

Lucide Merlina 78193/30/66 Manual

23 December 2024

Lucide Pippa 77583/81/30 Manual

23 December 2024

Lucide Pia 45380/04/30 Manual

23 December 2024

Lucide Pia 45280/01/30 Manual

23 December 2024

Lucide Anaka 45179/03/30 Manual

23 December 2024

Lucide Zych 45156/01/97 Manual

23 December 2024