Conair HC5000 Manual

Conair Ikke kategoriseret HC5000

Læs nedenfor 📖 manual på dansk for Conair HC5000 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Instruction Booklet

For your safety and continued enjoyment

of this product, always read the instruction

booklet carefully before using.

Model HC5000

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, especially

when children are present, take basic safety

precautions, including the following:

READ ALL INSTRUCTIONS

BEFORE USING

KEEP AWAY

FROM WATER

FOR HOUSEHOLD

USE ONLY

DANGER – Any appliance is

electrically live, even when the switch is off.

To reduce the risk of death or injury by

electric shock:

1. Unplug this appliance before cleaning.

2. Do not place or store appliance where it

can fall or be pulled into a tub or sink.

3. Do not use while bathing or in the shower.

4. Do not place in, or drop into water or

other liquids.

5. Do not reach for an appliance that has

fallen into water. Unplug immediately. For

dry location use only. Do not expose to liq-

uids, vapor or rain.

6. Except when charging, always unplug this

appliance from electrical outlet immediately

after using.

WARNING – To reduce the

risk of burns, electric shock, fire, or injury

to persons:

1. This appliance should never be left

unattended when plugged in. Do not pull,

twist, or wrap line cord around appliance.

2. This appliance should not be used by, on

or near children or individuals with certain

disabilities.

3. Use this appliance only for its intended

purpose as described in this manual. Do not

use attachments not recommended by the

manufacturer. Do not use an extension cord

to operate this appliance.

4. Never operate this appliance if it

has a damaged cord or plug, if it is not

working properly or if it has been dropped

or damaged, or dropped into water.

Return the appliance to a service center for

examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any

opening on this appliance.

7. Do not place appliance on any surface

while it is operating.

8. Do not use this appliance with a damaged

or broken comb or with teeth missing from

the blades as injury may occur. Before use,

make certain blades are aligned properly.

9. Do not use outdoors or operate where

aerosol (spray) products are being used or

where oxygen is being administered.

10. Never operate the appliance with the

air openings blocked or while on a soft

surface, such as a bed or couch, where the

air openings may be blocked. Keep the air

openings free of lint, hair, and other debris.

11. Always attach plug to appliance first, then

to outlet. To disconnect, turn all controls to

OFF, then remove plug from outlet.

12. This appliance is not a toy. Keep away

from children.

SAVE THESE

INSTRUCTIONS

OPERATING

INSTRUCTIONS

This appliance is intended for household use.

Use on alternating current (AC) 120V AC,

60 hertz only.

This appliance has a polarized plug (one

blade is wider than the other). As a safety

feature, this plug will fit in the outlet only one

way. If the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit, contact

a qualified electrician. Do not attempt to

defeat this safety feature.

Your new Conair® haircut kit has everything

you need to achieve professional haircuts at

home. It features a powerful clipper with

adjustable taper control and Japanese steel

blades. Also included are 8 comb attachments

for different hair lengths. It also comes with a

barber comb, barber scissors, cleaning brush,

barber cape, a carry case for easy storage

and travel, lubricating oil and a blade guard

for easy maintenance of the clipper blades.

OILING THE BLADES (OIL INCLUDED)

1. Oil the clipper blades once a month

2. Turn the clipper ON

3. Hold and point the blades downward

4. Spread one drop of oil across the blades

5. Turn the clipper OFF and wipe away any

excess oil

KEEP OIL AWAY FROM CHILDREN.

THE CONAIR GUIDE TO CUTTING

HAIR AT HOME

Before you start:

1. Inspect your clipper. Make sure it’s free of

hair and dirt, properly oiled and running

smoothly.

2. Place the barber cape or a towel around

the neck of the person whose hair is to be

cut.

3. Seat the person so that his or her head is

at your eye level. This gives you greater

visibility and control.

4. First, comb hair until it’s tangle free. Then

hold clipper in a comfortable grip. Now you’re

ready to cut.

MEDIUM TO LONG CUT

To begin, cut only a small amount of hair until

you become used to the length each

attachment leaves the hair. Try the longest

attachment on the clipper ﬁrst. If you want a

shorter cut, you can then use shorter combs.

• Short comb ttachment (number 1) cuts

hair to 1/8" (3mm).

• Medium-Short comb ttachment (number

2)) cuts hair to 1/4" (6mm

• Medium-Long comb ttachment (number 3)

cuts hair to 3/8" (10mm).

• Long comb ttachment (number 4) cuts hair

to 1/2" (13mm).

• Long comb ttachment (number 5) cuts hair

to 5/8" (16mm).

• Long comb ttachment (number 6) cuts hair

to 3/4" (19mm).

• Long comb ttachment (number 7) cuts hair

to 7/8" (22mm).

• Long comb ttachment (number 8) cuts hair

to 1" (25mm).

Attach combs by

holding them teeth

up, then snapping

onto the bottom of

the clipper blade.

To remove comb

attachments, place

index finger and

thumb as illus-

trated; then pull

out and up.

NOTE: Never push or shove the clipper

through the hair to make it move more

quickly. Professional experience shows

that the clipper works most efficiently

when it cuts through the hair at its

own speed.

USER MAINTENANCE

INSTRUCTIONS

CARE OF YOUR CLIPPER

IF YOU DETERMINE THAT BLADE

ALIGNMENT IS INCORRECT:

Conair® hair clippers are carefully inspected

to ensure that the blades are in perfect align-

ment. Of course, you will need to realign the

blades after removal for cleaning or replace-

ment, or if they should be knocked out of

alignment. How can you tell if blades need

realigning? Simply match them up, point for

point, to conform with FIG. 1 below:

FIG. 1

Bottom Blade

Top Blade

1/32" to 1/16"

To prevent the clipper from contacting the

skin or cutting too closely, make certain that

the end top blade teeth are 1/32" to 1/16"

back from bottom blade.

To Align Blades:

1. Unplug clipper and slightly loosen screws.

(See FIG. 2)

2. Position the extreme left-hand tooth of the

top blade so that it either covers or appears

on the left of the first small tooth on the

bottom blade.

3. Make sure that the big

tooth on the bottom blade

touches the extreme

right-hand tooth of the

top blade.

FIG. 2

POWER SCREW

The power screw permits you to adjust

power to your clipper. You may need to make

this adjustment if the power in your house

is low. (The Conair® clipper was designed for

household use.)

1. With a screwdriver or a dime, turn the

power screw counterclockwise until the noise

stops, and then turn about 45 degrees more.

(Fig.1)

Fig. 1

2. Then turn the screw clockwise, until the

arm strikes a coil, making a clacking noise.

(Fig. 2)

Fig. 2

ADJUSTABLE TAPER LEVER

Just like professional clippers, the Conair®

taper lever is positioned at your thumb.

You can hold the clipper in your hand and

adjust the lever at the same time... while

you’re clipping.

This taper lever eliminates the need in some

situations for a comb attachment because it

lets you gradually adjust the closeness of the

cut. For the closest cut and the shortest hair,

push taper lever up as far as it will go, to level

#1. To increase cutting length, slowly push

lever down. If you push to the lowest position,

level #5, it will leave hair about the same

length as the short comb attachment.

Because a different cutting edge is used in

each setting, the taper lever lengthens the life

of your blades.

Packed-in hair can slow down any clipper. To

remove hair without removing the blades, do

what the professionals do: Keeping the clipper

on, quickly push the taper lever back and

forth from “close” to “longer” cut a few times.

If you do this after every clipping, especially

with heavy hair cutting, the blades should

remain free of cut hair.

NOTE: Never pull on the clipper cord. Never

twist or wrap the cord around the clipper. Lay

it flat with the cord coiled up when not in use.

STORAGE: When not in use, your clipper

should be disconnected, allowed to cool and

stored in a safe, dry location, out of reach of

children.

Any other servicing should be performed by

an authorized service representative.

This appliance has no user-serviceable parts.

This appliance is for household use.

Close Cut

Longer Cut

To begin cutting hair:

1. The hair should be

combed in its natural

direction.

2. Using the longest

comb attachment, trim

sides from the bottom

upward. Hold clipper

lightly against the hair

with teeth of the comb

attachment pointing

up ward, yet flat against

the head. Gradually lift

the clipper upward and

outward through the hair,

trimming just a little at

a time.

Repeat around sides and

back of head.

If you want hair to be

even shorter:

A) Apply more pressure

to the head with the comb attachment that is

in place. This takes a little practice, of course.

B) Just switch to a shorter comb attachment.

Remember, it’s better to

leave too much hair than

too little. For longer hair o

top, use the barber comb

and lift hair on the top of

the head, cutting over the

comb. Or hold the hair

between the fingers and

cut to desired length. Always working from

the front to the back of the head, gradually

cut the hair shorter by reducing the space

between the comb or fingers and the head.

Comb often to check for uneven strands,

and to get rid of trimmed hair.

OUTLINING

Outlining requires no

attachments. Comb hair into

the desired style. Position

the clipper between the

sideburns and the ear (see

illustration), making sure the

corner edge of the blade is

against the hairline. With the

outline of the hair as your

guide, slowly move the clip-

per over, around and behind

the ears. For the back of

the neck and the sideburns,

hold the clipper upside down (see illustration)

and, holding it against the skin at the length

desired, move the clipper downward.

STOP. COMB. CHECK.

For best results, do as the professionals do:

Comb hair often, and check clipping results

as you comb. This way you avoid uneven

sides, bangs, neckline, etc.

SHORT CUTS TO PERFECT

FLATTOPS, CREW CUTS, ETC.

Always cut from the back of the neck to

the crown, using the longest comb setting.

Hold the comb attachment flat against the

head and slowly move the clipper up through

the hair. Use the same technique for the

sides, cutting from the bottom to the

upper side of the head.

For the front to the crown,

cut the hair against the

direction in which it grows.

Then even it up with

the sides.

For a flattop, use the

flat comb, not the comb

attachment. Just cut hair

on top of the head over flat

comb (see illustration).

Taper

control

Stainless steel,

self-sharpening

blades

Powerful

magnetic

motor

On/Off

switch

WARNING:

IF YOU THINK

THE POWER IS OFF

WHEN THE SWITCH

IS OFF,

YOU’RE WRONG.

KEEP AWAY FROM WATER

Everyone knows that electricity and water

are a dangerous combination. But did you

know that an electric appliance is still

electrically live even if the switch is off? If

the plug is in, the power is on. So when you

are not using your appliances, keep them

unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES

LIMITED FIVE-YEAR WARRANTY

(U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your

unit free of charge for 60 months from the date of

purchase if the appliance is defective in workmanship

or materials.

To obtain service under this warranty, return the

defective product to the service center listed on back,

together with your purchase receipt and $3.00 for

postage and handling. California residents need only

provide proof of purchase and should call

1-800-3-CONAIR for shipping instructions. In the

absence of a purchase receipt, the warranty period

shall be 60 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS,

OR LIABILITIES, INCLUDING BUT NOT

LIMITED TO THE IMPLIED WARRANTY OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL BE LIMITED IN

DURATION TO THE 60-MONTH DURATION OF THIS

WRITTEN, LIMITED WARRANTY. Some states do not

allow limitations on how long an implied warranty

lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES FOR BREACH OF THIS

OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,

WHATSOEVER. Some states do not allow the exclusion

or limitation of special, incidental, or consequential

damages, so the above limitation may not apply

to you.

This warranty gives you speciﬁc legal rights,

and you may also have other rights, which vary from

state to state.

Model

HC5000-BLD

Model HC OIL

Model SC-1

Model HC5000-3 Model HC5000-4

Model HC5000-1

Model HC-1

Please register this product at

www.conair.com/registration

Service Center

Conair Corporation

Service Department

7475 North Glen Harbor Blvd.

Glendale, AZ 85307

17PG030788

IB-15303

CUT HERE

HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM

Pricing in effect through December 31, 2018. Orders postmarked after this date

will be accepted, and the customer will be notified if pricing has changed.

ITEM PART # PRICE QUANTITY AMOUNT

Clipper Blade HC5000-BLD $6.50

4 Comb Attachments: 1/8", 1/4", 3/8", 1/2"

HC5000-4 $5.00

3 Comb Attachments: 5/8

, 3/4

, 7/8

HC5000-3 $5.00

1" Comb Attachment HC5000-1 $2.00

Lubricating Oil (pkg. of 3 tubes) HC OIL $1.00

Barber Scissors SC-1 $2.00

Blade Guard HC-1 $1.00

Subtotal

Sales Tax*

TOTAL

Enclose check or money order made payable to Conair. (We cannot accept cash, stamps

or C.O.D. orders.) *CT, IL, AZ, and PA residents should add applicable state sales tax.

Minimum order of $10.00 or a $2.00 handling charge will be added to order.

Mail to:

All prices include handling and return postage. Prices are subject to change without Conair Corporation

notice. Prices are valid only for shipments within the continental United States. Service Department

Please allow 4–6 weeks for delivery.

150 Milford Road

East Windsor, NJ 08520-9730

To avoid delays, please print clearly.

We must have a street address, as UPS cannot deliver to a P.O. box.

NAME _________________________________________________________________________________________________

ADDRESS APT. ___________________________________________ ______________________________________________

CITY ________________________________ ________________________________________________STATE _________ ZIP

TELEPHONE ( ) _____________________________________________________________

(We call only if we have a question about your order.)

For information on other Conair

® haircut kit parts call: 1-800-3-CONAIR.

Produkt Specifikationer

Mærke:	Conair
Kategori:	Ikke kategoriseret
Model:	HC5000

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair HC5000 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Conair Manualer

Conair MiniPRO CS80N Manual

1 Oktober 2024

Conair MASK2 Manual

1 Oktober 2024

Conair skn SFB11GK Manual

1 Oktober 2024

Conair Man GMTL6000 Manual

6 September 2024

Conair LNT1 Manual

6 September 2024

Conair Man GMT189R Manual

6 September 2024

Conair InfinitiPRO 998 Manual

3 September 2024

Conair CD117NN Manual

2 September 2024

Conair LLT2 Manual

2 September 2024

Conair CLS1X Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron Overbridge Manual

26 November 2024

Elektron Sidstation Manual

26 November 2024

SKROSS World Adapter Pro+ Manual

26 November 2024

SKROSS PRO – World & USB Manual

26 November 2024

SoundTube IPD-RS82-EZ Manual

26 November 2024

Kramer 4x1VB Manual

26 November 2024

Kramer RC-63A Manual

26 November 2024

SoundTube IPD-HP82-EZ Manual

26 November 2024

Kramer RK-KVM-1U-PP3 Manual

26 November 2024

Gioteck VX-2 (PS3) Manual

26 November 2024