Conair HCT401N Manual


Læs nedenfor 📖 manual på dansk for Conair HCT401N (3 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/3
STOP. COMB. CHECK.
For best results, do as the professionals do:
comb hair often, and check clipping results as
you comb. This way you avoid uneven sides,
bangs, neckline, etc.
SHORT CUTS TO PERFECT
FLAT TOPS, CREW CUTS, ETC.
Always cut from the back of the neck to the
crown, using the longest comb setting.
Hold the comb attachment flat against the
head and slowly move the clipper up through
the hair. Use the same technique for the sides,
cutting from the bottom to the upper side of
the head.
For the front to the crown, cut the hair against
the direction in which it grows. Then even it
up with the sides.
For a flat top, use the flat comb, not the
attachment comb. Just cut hair on top of the
head over flat comb. (see above).
To taper hair down to the neckline, use
attachment comb #1. Comb hair andcheck
for uneven spots. Outline sideburns and neck
areas (see “Outlining”).
®
H O M E H A I R C U T T I N G K I T
MULTI-PURPOS
includes clipper,
trimmer and nose/e
detailer for all your
grooming needs
CLIPPER
,
TRIMMER
& NOSE/EAR DETAILER
3 1 kit-in-
Instructions for Clipper Care and Use
Model HCT401
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, basic safety pre-
cautions should always be taken, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING
FOR HOUSEHOLD USE ONLY
KEEP AWAY FROM WATER
DANGER
Any appliance is electrically
live, even when the switch is off.
To reduce the risk of death or injury by electric
shock:
1. Always unplug this appliance from electri -
cal outlet immediately after using.
2. Unplug this a ppliance before cleaning. Unplug
the appliance when not in use.
3. Do not place or store a ppliance where it can fall
or be pulled into a tub or sink.
4. Do not use while bathing or in a shower.
5. Do not place in, or drop into water or other
liquid.
6. Do not reach for an appliance that has
fallen into water. Unplug immediately.
WARNING
To reduce the risk of burns,
electric shock, fire, or injury to persons:
1. This appliance should never be left unattended
when plugged in. Do not pull, twist, or wrap line
cord around appliance.
2. This appliance should not be used by, on, or
near children or individuals with certain dis-
abilities.
3. Use this a ppliance only for its intended purpose
as described in this manual. Do not use attach-
ments not recommended by the manufacturer.
Do not use an extension cord to operate this
appliance.
4. Never opera te this appliance if it has a dam-
aged cord or plug, if it is not working properly or
if it has been dropped or damaged, or dropped
into water. Return the appliance to a service
center for examination and repair.
5. Keep the cord a way from heated surfaces.
6. Never drop or insert an y object into any opening
on this appliance.
7. Do not place a ppliance on any surface while it
is operating.
8. Do not use this a ppliance with a
damaged or broken comb or with teeth miss-
ing from the blades as injury may occur. Before
use, make certain blades are aligned properly.
(See “Care of your Clippers.”)
9. Do not use outdoors or opera te where aerosol
(spray) products are being used or where oxy-
gen is being administered.
10. Never opera te the appliance with the air open-
ings blocked or while on a soft
surface, such as a bed or couch, where the air
openings may be blocked. Keep the air
openings free of lint, hair, and other debris.
11. Always attach plug to appliance first, then to
outlet. To disconnect, turn all con trols to “OFF”,
then remove plug from outlet.
12. Avoid skin contact with moving blade.
13. Keep lubricating oil out of reach of children.
14. When using the appliance with its cord, be
mindful of tangles or kinks in the cord. If
the cord does become tangled during use,
turn the unit off and straighten cord before
operating again.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
This appliance is intended for household use.
Use on Alternating Current 120V/60 hertz only.
This appliance has a polarized plug (one blade
is wider than the other). As a safety feature, this
plug will fit in the outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician
to install the proper outlet. Do not attempt to
defeat this safety feature.
Your new Conair® haircut kit has everything you
need to achieve professional haircuts at home. It
features a powerful clipper with adjustable taper
control and stainless steel blades for cutting
precision, a nose/ear trimmer and a detail trim-
mer that is great for necks, sideburns, goatees
and mustache trimming. Also included are 10
attachment combs (1/8" (3 mm), 1/4" (6 mm),
3/8" (9.5 mm), 1/2" (13 mm), 5/8" (16 mm), 3/4"
(19 mm), 7/8" (22 mm), 1" (25 mm) for different
hair lengths (left and right ear combs), barber
scissors, barber cape, deluxe storage case, bar-
ber comb with straight teeth, styling comb with
angled teeth, and 3 styling clips to assist you in
cutting longer hair styles. It also comes with lubri-
cating oil, a cleaning brush and a blade guard for
easy maintenance of the clipper blades.
THE CONAIR GUIDE
TO CUTTING HAIR AT HOME
Before you start:
1. Inspect your clipper. Make sure it’s free of hair
and dirt, properly oiled, and running smoothly.
2. Place a towel around the neck of the person.
3. Seat the person so that his or her head is at
your eye level. This gives you greater visibility
and control.
4. First, comb hair until its tangle-free. Then
hold clipper in a comfortable grip. Now you’re
ready to cut.
MEDIUM TO LONG CUT
To begin with, cut only a small amount of hair until
you become used to the length each attachment
leaves the hair. Try the longest attachment on the
clipper first. If you want a shorter cut, you can
then use shorter combs.
Short attachment comb (number 1) cuts hair
to 1/8” (3mm).
Medium-Short attachment comb (number 2)
cuts hair to 1/4” (6mm).
Medium-Long attachment comb (number 3)
cuts hair to 3/8” (9.5mm).
Long attachment comb (number 4) cuts hair
to 1/2” (12.5mm).
Long attachment comb (number 5) cuts hair
to 5/8" (16mm).
Long attachment comb (number 6) cuts hair
to 3/4" (19mm).
Long attachment comb (number 7) cuts hair
to 7/8" (22mm).
Long attachment comb (number 8) cuts hair
to 1” (25mm).
Left ear attachment comb lightly tapers over
left ear.
Right ear attachment comb lightly tapers over
right ear.
Attach combs by
holding them teeth
up, then snapping
onto the bottom of the
clipper blade.
To remove comb
attachments, place
index finger and
thumb as illustrated;
then pull out and up.
NOTE: Never push or shove the clipper
through the hair to make it move
more quickly. Professional experience
shows that the clipper works most
efficiently when it cuts through the
hair at its own speed.
To begin cutting hair:
1. The hair should be combed in its natural
direction.
2. Using the largest
attachment comb, trim
sides from the bottom
upward. Hold clipper
lightly against the hair
with teeth of the attach-
ment comb pointing
up ward, yet flat against
the head. Gradually lift
the clipper upward and
outward through the hair,
trimming just a little at
a time.
Repeat around sides and
back of head.
If you want hair to be
even shorter:
A) Apply more pressure
to the head with the
attachment comb that
is in place. This takes a
little practice, of course.
OR B) Just switch to
a shorter attachment
comb.
Remember, its better to
leave too much hair than
too little. For longer hair
on top, use the barber comb and lift hair on
the top of the head, cutting over the comb. Or
hold the hair between the fingers and cut to
desired length. Always working from the front
to the back of the head, gradually cut the hair
shorter by reducing the space between the
comb or fingers and the head. Comb often to
check for uneven strands, and to get rid of
trimmed hair.
OUTLINING:
Outlining requires no attachments. Comb
hair into the desired style. Position the clip-
per between the sideburns and the ear (see
below), making sure the corner edge of the
blade is against the hairline. With the outline
of the hair as your guide, slowly move the
clipper over, around and behind the ears.
For the back of the neck and the sideburns,
hold the clipper upside down (see above)
and, holding it against the skin at the length
desired, move the clipper downward.
USER-MAINTENANCE
INSTRUCTIONS
CARE OF YOUR CLIPPERS
IF YOU DETERMINE THAT BLADE
ALIGNMENT IS INCORRECT:
Conair® hair clippers are carefully inspected to
insure that the blades are in perfect alignment.
Of course you will need to realign the blades
after removal for cleaning or replacement, or
if they should be knocked out of alignment.
How can you tell if blades need realigning?
Simply match them up, point for point, to
conform with FIG. 1 below:
FIG. 1
To prevent the clipper from contacting the skin
or cutting too closely, make certain that the
end top blade teeth are 1/32 to 1/16” back
from bottom blade.
To Align Blades:
1. Add two or three drops
of Conair Lubricating Oil
(included).
2. Turn clipper on for a minute
to disperse oil evenly over
blades, then turn off.
3. Unplug clipper and slightly
loosen screws. (See FIG. 2)
FIG. 2
4. Position the extreme left-hand tooth
of the top blade so that it either covers or
appears on the left of the first small tooth on
the bottom blade.
5. Make sure that the big tooth on the
bottom blade touches the extreme right hand
tooth of the top blade.
SPECIAL OIL
To maintain the blades of your Conair clipper,
oil them after every three or four haircuts.
Gently place a few drops of oil on the teeth
of the blades, using the special Conair oil
included with your set. Turn the clipper on
for a minute, then turn off. This light, natural
oil was formulated specifically for the Conair
high-speed
clipper. Be cause it is the right oil to use, it
will not slow down the blades. Never use
any other product. There is no substitute for
Conair oil.
POWER SCREW
The power screw permits you to adjust
power to your clipper. You may need to make
this adjustment if the power in your house is
low. (The Conair
®
clipper was designed for
household use.)
1. With a screwdriver or a dime, turn the power
screw counter clockwise until the arm strikes
coil, making a clacking noise. (FIG.1)
FIG. 1
2. Then turn the screw clockwise, until the noise
stops and then turn about 45 degrees more.
This is the maximum power setting. (FIG. 2)
FIG. 2
OIL BLADE BEFORE USE.
ADJUSTABLE TAPER LEVER
Just like professional clippers, the Conair
taper lever is positioned at your thumb. You
can hold the clipper in your hand and adjust
the lever at the same time... while you’re
clipping.
This taper lever eliminates the need for
an attachment comb because it lets you
gradually adjust the closeness of the cut. For
the closest cut and the shortest hair, push
taper lever up as far as it will go. To increase
cutting length, slowly push lever down. If
you push to the lowest position, it will leave
hair about the same length as the short
attachment.
Because a different cutting edge is used in
each setting, the taper lever lengthens the
life of your blades.
Packed-in hair can slow down any clipper.
To remove hair without removing the blades,
do what the professionals do:
keeping the clipper on, quickly push the taper
lever back and forth from “close” to “longer”
cut a few times.
If you do this after every clipping, especially
with heavy hair cutting, the blades should
remain free of cut hair.
Close Cut
Longer Cut
If clipper stops cutting and this action doesn’t
help, check the blades. If they’ve become dull,
replace them or return them to a Conair service
center. Well be glad to
sharpen them for you. For new blades, send
check or money order for $6.50 (see order
blank) which includes postage and handling
(If $10 minimum is met) to:
Conair Corporation
150 Milford Rd.
East Windsor, NJ 08520
NOTE: Never pull on the clipper cord. Never
twist or wrap the cord around the clipper. Lay
it flat with the cord coiled up when not in use.
Bottom Blade
Adjustable
Taper Lever
Top Blade
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU'RE WRONG.
KEEP AWAY FROM WATER
Everyone knows that electricity and water
are a dangerous combination. But did you
know that an electric appliance is still
electrically alive even if the switch is off? If
the plug is in, the power is on. So when you
are not using your appliances, keep them
unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
LIMITED FIVE YEAR WARRANTY
Conair will repair or replace (at our option) your
unit free of charge for 60 months from the date
of purchase if the appliance is defective in
workmanship or materials.
To obtain service under this warranty, return the
defective product to the service center listed on back,
together with your purchase receipt and $3.00 for
postage and handling. California residents need only
provide proof of purchase and should call 1-800-
366-0937 for shipping instructions. In the absence of
a purchase receipt, the warranty period shall be 60
months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR
LIABILITIES, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL BE LIMITED IN DURATION TO THE 60
MONTH DURATION OF THIS WRITTEN, LIMITED
WARRANTY. Some states do not allow limitations
on how long an implied warranty lasts, so the above
limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. Some states do not allow the exclu-
sion or limitation of special, incidental, or conse-
quential damages, so the above limitation may not
apply to you.
This warranty gives you specific legal rights, and
you may also have other rights, which vary from
state to state.
Please register this product at
www.conair.com/registration
Service Center
Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
©2012 Conair Corporation
150 Milford Road, East Windsor, NJ 08520
7475 North Glen Harbor Blvd., Glendale, AZ 85307
12PG129785 IB-11276
Once again, thanks for buying a
Conair product.
Your Conair ® clipper blades are made of high
carbon stainless steel. They are engineered
for precise, professional results. If blades feel
like they are pulling or grabbing hair, it means
they are losing their sharpness and should be
replaced as soon as possible.
Attachment combs should also be replaced if
they are lost or broken. It is easier to cut hair
with the accuracy of a pro when the necessary
tools are at your fingertips.
Conair makes a variety of accessories for
different haircut kits. If your haircut kit does not
include them, you may want to consider adding
them to your professional haircutting tools.
Left and right ear attachment combs provide
effortless, precise cutting around the ears. Styling
clips hold hair in place when you are sectioning
hair. A styling comb makes it easy to taper or
cut hair at an angle. A barber cape ensures a
comfortable and neat haircut and a convenient
storage pouch keeps all your essentials in one
place.
Last but not least, an easy-to-follow 30-minute
Haircuts at Home video is available. It
demonstrates basic haircutting techniques and
follows four popular haircuts step by step. It
will give you the confidence and instruction
you need to give great looking haircuts to every
member of your family.
EXCITING ITEMS
FROM CONAIR
Cordless/rechargeable
multi-use trimmer
with 4 total blade
attachments for all your
grooming needs.
Model GMT189RGB
The first cordless,
rechargeable
angled shaving head with
an universal grip, 3-position
taper control, 3 attachment
combs and trimmer
attachment.
Model HG300
Model COMB-10
Model COMB-11
Model COMB-13
Model COMB-12
Model HCNB-1
Model CAPE-1
Model HC OIL
Model HC VIDEO
Model SC- 1
Model BLD- 8
Model BG30
Model CLP- 1
CUT HERE
HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM
Pricing in effect through December 31, 2013. Orders postmarked after this date
will be accepted, and the customer will be notified if pricing has changed.
ITEM PART # PRICE QUANTITY AMOUNT
Set of 4 Attachment Combs:1/8", 1/4", 3/8", 1/2".
Fits all clippers (HC200, HC220, HC240, HC102 $5.00 COMB-10
HC300, HC318, HC414, HC275, HC222)
Set of 2 Attachment Combs: left ear and right ear. Fits all clippers (see COMB-10).except HC222 $1.75COMB-11
1" Comb fits all clippers COMB-12 $1.75
3 attachment combs 5/8", 3/4", 7/8". Fits all clippers $5.00COMB-13
Neck Brush $1.50HCNB-1
Deluxe Black Vinyl Cape with Velcro Collar $5.00CAPE-1
Lubricating Oil (pkg. of 3 tubes) $2.00HC OIL
30 Minute Haircut Video $8.95HC VIDEO
Barber Scissors $2.00SC-1
Blade Set for HC200 Detent Clipper BLD-8 $6.50
Blade Guard $1.00BG30
Styling Clips (set of 3) $1.50CLP-1
Subtotal
Enclose check or money order made payable to Conair. (We cannot accept cash, stamps or C.O.D. orders.) CT, IL, AZ, and PA residents *Sales Tax
should add applicable state sales tax. Minimum order of $10.00 or a $2.00 handling charge will be added to order.
A l l p r i c e s i n c l u d e h a n d l i n g a n d r e t u r n p o s t a g e . P r i c e s a r e s u b j e c t t o c h a n g e w i t h o u t n o t i c e .
Prices are valid only for shipments within the Continental United States. Please allow 4-6 weeks for delivery. TOTAL
To avoid delays, please print clearly.
We must have a street address, as UPS cannot deliver to a P.O. box. Mail to:
Conair Corporation
NAME____ _________________________________________________________________________________ Service Department
150 Milford Road
ADDRESS APT. __________________________________________ __________________________________ East Windsor, NJ 08520-9730
CITY ZIP _______________________________________STATE _______________________ ______________
TELEPHONE (HONE ( _________________ (We call only if we have a question about your order.)
For information on other Conair® haircut kit parts call: 1-800-3-CONAIR.


Produkt Specifikationer

Mærke: Conair
Kategori: Ikke kategoriseret
Model: HCT401N

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair HCT401N stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Conair Manualer

Conair

Conair NPTCCA01 Manual

10 December 2024
Conair

Conair NPTCCA02 Manual

10 December 2024
Conair

Conair MASK2 Manual

1 Oktober 2024
Conair

Conair skn SFB11GK Manual

1 Oktober 2024
Conair

Conair Man GMTL6000 Manual

6 September 2024
Conair

Conair LNT1 Manual

6 September 2024
Conair

Conair Man GMT189R Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024