Conair HCT45N Manual

Conair Ikke kategoriseret HCT45N

Læs nedenfor 📖 manual på dansk for Conair HCT45N (3 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

Instructions for Care and Use

MODEL HCT45

HCT45 IB-13112.indd 2

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, especially

when children are present, basic safety precau-

tions should always be followed, including the

following:

READ ALL INSTRUCTIONS

BEFORE USING

FOR HOUSEHOLD ONLY

KEEP AWAY FROM WATER

DANGER – Any appliance is electrically

live, even when the switch is off.

To reduce the risk of death or injury by electric

shock:

1. Unplug this appliance before cleaning.

2. Do not place or store appliance where it can fall or

be pulled into a tub or sink.

3. Do not use while bathing or in a shower.

4. Do not place in, or drop into, water or other liquids.

5. Do not reach for an appliance that has fallen into

water. Unplug immediately.

6. Always unplug this appliance from electrical outlet

immediately after using.

WARNING – To reduce risk of burns,

electrocution, fire, or injury to persons:

1. This appliance should never be left unat-

tended when plugged in. Do not pull, twist, or

wrap line cord around appliance.

2. This appliance should not be used by, on, or near

children or individuals with certain disabilities.

3. Use this appliance only for its intended purpose

as described in this manual. Do not use attachments

not recommended by the manufacturer. Do not use

an extension cord to operate this appliance.

4. Never operate appliance if it has a damaged

cord or plug, or if it is not working properly, if it has

been dropped or damaged, or dropped into water.

Return appliance to a service center for examina-

tion and repair.

5. Keep cord away from heated surfaces.

6. Never drop or insert any object into any opening

on this appliance.

7. Do not place appliance on any surface while it is

operating.

8. Do not use this appliance with a damaged

or broken comb or with teeth missing from the

blades, as injury may occur. Before use, make

certain blades are aligned properly. (See “Care of

Your Clippers.”)

9. Do not operate outdoors or where aerosol (spray)

products are being used or oxygen is being admin-

istered.

10. Never operate the appliance with the air open-

ings blocked or while on a soft surface, such as

a bed or couch, where the air openings may be

blocked. Keep the air openings free of lint, hair, and

the like.

11. Always attach plug to appliance first, then to

outlet. To disconnect, turn all controls to “OFF”;

remove plug from outlet.

12. Avoid skin contact with moving blades.

13. Always check for tangles or kinks in the cord. If

the cord does become tangled during use, turn unit

off and straighten cord before operating.

SAVE THESE

INSTRUCTIONS

OPERATING

INSTRUCTIONS

This appliance is intended for household use. Use

on Alternating Current (120V AC 60Hz) only. This

appliance has a polarized plug (one blade is wider

than the other). As a safety feature, this plug will

fit in the outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug. If it still

does not fit, contact a qualified electrician. Do not

attempt to defeat this safety feature.

Your new Conair® Clipper and Trimmer Kit has

everything you need to achieve professional

haircuts, beard trimming and detailing at home.

Its powerful new torque motor clipper, with steel

blades for long-lasting cutting precision, features

a new 5-position adjustamatic taper control.

Whatever hair length you set the button for, the

clipper will automatically cut all hair in that section

at the desired length. Also included are 9 attach-

ment combs for different hair lengths (including

left and right ear taper combs), barber scissors, a

styling comb with angled teeth, a full-length barber

cape and a soft, foldable pouch for easy storage.

It also comes with lubricating oil, a cleaning brush

and a blade guard for easy maintenance and pro-

tection of the clipper blades.

In addition, your kit has a full-size detailing trimmer

to trim facial and neck hair precisely.

GUIDE TO CUTTING HAIR AT HOME

Before you start:

1. Inspect your clipper. Make sure it’s free of hair

and dirt, properly oiled, and running smoothly.

2. Place cape around the neck of the person getting

a haircut.

3. Seat the person so that his or her head is at

your eye level. This gives you greater visibility and

control.

4. First, comb hair until it’s tangle free. Then hold

clipper in a comfortable grip. Now you’re ready

to cut.

MEDIUM TO LONG CUT

To begin with, cut only a small amount

of hair until you become used to the length each

attachment leaves the hair. Try the longest attach-

ment comb and put the taper control in the high-

est setting. If you want a shorter cut, you can then

use shorter combs.

• Short attachment comb (#1) cuts hair to 1/8".

• Medium-Short attachment comb (#2) cuts hair to 1/4".

• Medium-Long attachment comb (#3) cuts hair to 3/8".

• Long attachment comb (#4) cuts hair to 1/2".

• Long attachment comb (#5) cuts hair to 5/8".

• Long attachment comb (#6) cuts hair to 3/4".

• Long attachment comb (#7) cuts hair to 7/8".

• Left ear attachment comb lightly tapers over left ear.

• Right ear attachment comb lightly tapers over right ear.

These combs make this part of the haircut easier.

Attach combs by holding

them teeth up, then snapping

them onto the bottom of the

clipper blade.

To remove comb attach-

ments, place index finger

and thumb as illustrated;

then pull out and up.

NOTE: Never push or shove the clipper through

the hair to make it move more quickly.

Professional experience shows that the clipper

works most efficiently when it cuts through the

hair at its own speed.

To begin cutting hair:

1. The hair should be combed in its natural

direction.

2. Using the largest attachment comb, trim sides

from the bottom upward. Hold clip per lightly

against the hair with teeth of the attachment comb

pointing up ward, yet flat

against the head.

Gradually lift the clip per

upward and outward through

the hair, trimming just a little

at a time. Repeat around sides

and back of head.

If you want hair to be even

shorter:

A) Apply more pressure to

the head with the attach-

ment comb that is in place.

This takes a little practice, of

course.

B) Just switch to a shorter

attachment comb.

Remember, it’s better to leave

too much hair than too little.

For longer hair on top, use the

styling comb and lift hair on

the top of the head, cutting

over the comb, or hold the hair

between the fingers and cut to

desired length. Always working

from the front to the back of the

head, gradually cut the hair

shorter by reducing the space

between the comb or fingers and the head. Comb

often to check for uneven strands, and to get rid of

trimmed hair.

*Equipped with a turbo switch, this unit is designed

to provide extra power making it easier to cut

thicker, coarser hair.

OUTLINING

Outlining requires no attach-

ments. Comb hair into the

desired style. Position the clipper

between the sideburns and the

ear, making sure the corner edge

of the blade is against the hair-

line. With the outline of the hair

as your guide, slowly move the

clipper over, around and behind

the ears. For the back of the neck

and the sideburns, hold the clip-

per upside down (see across) and,

holding it against the skin at the

length desired, move the clipper downward.

STOP. COMB. CHECK.

For best results, do as the professionals do: Comb hair

often, and check clipping results as you comb. This

way you avoid uneven sides, bangs, neckline, etc.

FOR ULTRA-CLOSE FADE STYLES:

A fade cut is a haircut that starts with very short hair

(almost bald) on the sides of the head, but lengthens

as it nears the top.

1. Start with clean, dry hair. If hair is fairly long, use

a long comb attachment (ideally #4) to remove the

bulk of your hair before starting the fade cut.

2. Using the long comb attachment, trim hair, cutting

against the growth of your hair (from base of neck

up toward top of head). At first, until you become

familiar with the different attachments, begin with a

longer one. You can always go back and make your

hair a little shorter. Brush or comb away cuttings as

you go. Do not force the blades through the hair. Let

the trimmer do the work. Using the #1 comb attach-

ment, you can cut hair as short as 1/8".

3. Gradually trim hair from entire head, rotating

trimmer when necessary. Keep cutting against the

natural growth of your hair.

4. Establish the fade line. Remove comb attach-

ments. With the taper control in position #1, start by

blending the hair at the fade line by trimming up and

out, repeating as you rotate around the head. Cut

hair shorter on the sides and base of the head than

on the top of the head.

5. With the taper control in the #5 position, the blade

is as close as it can be to the head. Now repeat the

above process, virtually removing all hair. Begin at

the base of the scalp and blend toward the fade line.

The goal is to blend the hair so there is no real line,

just a perfect fade from bald on the sides to very

short hair on the top. Continue blending – remember

to comb or brush hair against the natural growth

to remove cuttings as you go until you achieve the

desired look.

FOR THE BALD CUT

Follow the instructions for the fade cut, cutting

hair progressively shorter with each pass of

the clipper. For a bald effect, remove all comb

attachments and move the taper control to the #5

position. To receive maximum closeness, overlap

strokes in a crisscross pattern. To achieve a

smooth, bald look, we recommend you finish by

using a razor with lather to shave entire head.

SHORTCUTS TO PERFECT

FLATTOPS, CREW CUTS, ETC.

Always cut from the back of the neck to the crown,

using the longest comb setting. Hold the comb

attachment flat against the head and slowly move

the clipper up through the hair. Use the same tech-

nique for the sides, cutting from the bottom to the

upper side of the head.

For the front to the crown, cut the hair against the

direction in which it grows, then even it up with

the sides.

For a flattop, use the flat comb, not the attachment

comb. Just cut hair on top of the head over flat

comb (see below).

To taper hair down to the neckline, use

attachment comb #1. Comb hair and check for

uneven spots. Outline sideburns and neck areas

(see “Outlining”).

USER MAINTENANCE

CARE OF YOUR CLIPPERS

DETACHABLE BLADE SET

This clipper comes with a

detachable blade set.

To remove the blades follow

these steps:

1. Hold the front part of the

clipper with your thumb

pressing on the blade and

place another hand against

the blade (See Fig. 1).

2. When pressing the blade

forward, the blade is detached

(See Fig. 2).

TO REPLACE BLADE:

1. Set the Taper Control Button

to lowest position “1”

(See Fig. 3.)

2. Place the blade onto the

clipper body by inserting the

“Blade Tongue” down below

the “Lock Tap”(See Fig. 4).

3. Snap the blade down into following position.

The blade is now fixed onto the clipper body

(See Fig. 5).

Use these instructions to switch between the

clipper and beard trimmer blades and back.

SPECIAL OIL

To maintain the blades

of your Conair clipper,

oil them after every

three or four haircuts.

Gently place a few drops of oil on the teeth of the

blades, using the special Conair

oil included with

your set. Turn the clipper on for a minute, then turn

off. This light, natural oil was formulated specifi-

cally for the Conair high speed clipper. Be cause

it is the right oil to use, it will not slow down the

blades. Never use any other product. There is no

substitute for Conair oil.

Keep oil out of reach of children.

TURBO FEATURE

This product is equipped with a turbo boost button.

When activated, this will provide more cutting power.

This is especially useful for cutting through thicker hair.

To activate the turbo feature:

1. Turn the Power switch to the “on” position.

2. Press the Turbo button.

3. Continue to press the Turbo button for as long as

you need the extra power.

4. Release the Turbo button to return to normal

power.

ADJUSTABLE 5-POSITION

TAPER CONTROL

Just like levers on professional clippers, the Conair

taper control is positioned at the back of the unit,

which functions for both the clipper and trimmer

blade so you can hold the clipper in your hand and

adjust the lever at the same time...while you’re

clipping/trimming. This taper control eliminates the

need in some situations for an attachment comb,

because it lets you gradually adjust the closeness

of the cut. For the closest cut and the shortest hair,

push taper control up as far as it will go to level

#1. To increase cutting length,

slowly push control down. If

you push to the lowest posi-

tion, level #5 or #4, it will leave

hair about the same length as

the short attachment comb.

Because a different cutting edge is used in each

setting, the taper lever lengthens the life of your

blades. Packed-in hair can slow down any clipper.

To remove it without removing the blades, take your

cleaning brush and brush the hair from the blades.

If you do this after every clipping, especially with

heavy hair cutting, the blades should remain free

of cut hair. If clipper stops cutting and this action

doesn’t help, try loosening the blades to remove the

hair.

Any other servicing should be performed by an

authorized service representative. The appliance has

no user serviceable parts. The product is for house-

hold use only. (See Important Safety Instructions).

If clipper stops cutting, check to see if there is a

clump of hair lodged between the blades. If that is

the problem, unplug the clipper and then loosen the

blades to remove the hair.

If the clipper stops cutting, but does not stop run-

ning, you will need to check the blades. For new

blades, send check or money order for $6.50

which includes postage and handling to:

Conair Corporation

150 Milford Rd.

East Windsor, NJ 08520

STORAGE

When not in use, your clipper should be discon-

nected, allowed to cool and stored in a safe, dry

location, out of reach of children.

Any other servicing should be performed by an

authorized service representative. This appliance

has no user-serviceable parts. The product is for

household use only.

NOTE: Never pull on the clipper cord. Never

twist or wrap the cord around the clipper. To

store your clipper, lay it flat with the cord coiled

up, then place in case.

TO OPERATE TRIMMER

1. Remove the battery cover

at the back of the unit by pull-

ing straight down. (Fig. 1)

2. Being careful not to bend

the clips, insert the negative

end of the battery first, so it

will slip easily into position.

3. Return the battery cover to

its original position by pushing

it into place.

4. To use your trimmer, push ON/OFF switch

upward to ON position.

5. After you finish using your trimmer, push down

on the ON/OFF switch to turn the trimmer off.

6. Always purchase the correct size and grade of

battery most suitable for the intended use.

7. Replace the battery once it is no longer functional.

8. Clean the battery contacts and also those of the

device prior to battery installation.

9. Ensure the battery is installed correctly with

regard to polarity (+ and -).

10. Remove battery from equipment that is not to

be used for an extended period of time.

11. Remove used battery promptly.

12. Store unused batteries in their original

packaging, away from metal objects that could

short-circuit them. Never short-circuit batteries.

13. Never dispose of batteries in fire, except under

conditions of controlled incineration. Failure to

observe this precaution may result in an explosion.

Never attempt to recharge primary batteries as this

may cause leakage, fire, or explosion.

*Trimmer requires 1 AA battery (not included).

We recommend using alkaline batteries in your

trimmer because they last longer. If you are not

going to use your trimmer for a long period of time,

or if the battery is dead, remove the battery from

the unit. This will increase the life of your trimmer.

Fig. 1

TAKING CARE OF YOUR TRIMMER

BLADE CARE

Because the trimmer blades are precision made for

a very special use, they should always be handled

with care. Each time you finish using the trimmer,

take a cleaning brush and brush away any loose

hair that has collected in the blades.

To promote the long life of the appliance, use

your trimmer only for the purpose intended by the

manufacturer.

TO CLEAN YOUR TRIMMER

Make sure trimmer is off.

1. To remove the trimmer head for

cleaning, turn the head counter-clock-

wise until the “I” mark aligns with the

arrow mark, then lift the head gently

(Fig. 1).

2. Only rinse the head under water

(Fig. 2). For proper functioning of the

unit, the handle cannot touch or be

immersed in water.

3. After cleaning, make sure to shake

dry the head before replacing it on

the body.

4. To reassemble the head onto the

body, align the “I” mark on the head

with the arrow mark on the body

and then turn clockwise until the “I”

mark aligns with the circle mark on

the body (Fig. 3).

5. Add a few drops of oil provided to the

blades and run unit for 30 seconds for proper

lubrication.

(Fig. 1)

(Fig. 2)

(Fig. 3)

HCT45 CLIPPER & DETAIL TRIMMER

5-position taper

control switch

Back view

Front view

Cleaning

brush

Oil

Detachable

blade set

1. 20mm trimmer head

2. No-slip Grip™ handle

3. Cordless/battery operated

(requires AA battery; not included)*

WARNING:

IF YOU THINK

THE POWER IS OFF

WHEN THE SWITCH

IS OFF,

YOU’RE WRONG.

KEEP AWAY FROM WATER

Everyone knows that electricity and water are a

dangerous combination. But did you know that

an electrical appliance is still electrically alive

even if the switch is off? If the plug is in, the

power is on. So when you are not using your

appliances, keep them unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES

LIMITED FIVE-YEAR

CLIPPER WARRANTY

Conair will repair or replace (at our option) your

unit free of charge for 60 months from the date

of purchase if the appliance is defective in

workmanship or materials.

To obtain service under this warranty, return the

defective product to the service center listed on

back, together with your purchase receipt and

$3.00 for postage and handling. California residents

need only provide proof of purchase and should call

1-800-3-CONAIR for shipping instructions. In the

absence of a purchase receipt, the warranty period

shall be 60 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR

LIABILITIES, INCLUDING BUT NOT LIMITED TO

THE IMPLIED WARRANTY OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE,

SHALL BE LIMITED IN DURATION TO THE 60-

MONTH DURATION OF THIS WRITTEN, LIMITED

WARRANTY. Some states do not allow limitations

on how long an implied warranty lasts, so the above

limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR

ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES FOR BREACH OF THIS OR ANY

OTHER WARRANTY, EXPRESS OR IMPLIED,

WHATSOEVER. Some states do not allow the exclu-

sion or limitation of special, incidental, or conse-

quential damages, so the above limitation may not

apply to you.

This warranty gives you specific legal rights, and

you may also have other rights, which vary from

state to state.

LIMITED TWO-YEAR

TRIMMER WARRANTY

Conair will repair or replace (at our option) your

unit free of charge for 24 months from the date

of purchase if the appliance is defective in

workmanship or materials.

To obtain service under this warranty, return the

defective product to the service center listed on

back, together with your purchase receipt and

$3.00 for postage and handling. California residents

need only provide proof of purchase and should call

1-800-3-CONAIR for shipping instructions. In the

absence of a purchase receipt, the warranty period

shall be 24 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR

LIABILITIES, INCLUDING BUT NOT LIMITED TO

THE IMPLIED WARRANTY OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE,

SHALL BE LIMITED IN DURATION TO THE 24-

MONTH DURATION OF THIS WRITTEN, LIMITED

WARRANTY. Some states do not allow limitations

on how long an implied warranty lasts, so the above

limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR

ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES FOR BREACH OF THIS OR ANY

OTHER WARRANTY, EXPRESS OR IMPLIED,

WHATSOEVER. Some states do not allow the exclu-

sion or limitation of special, incidental, or conse-

quential damages, so the above limitation may not

apply to you.

This warranty gives you specific legal rights, and

you may also have other rights, which vary from

state to state.

Please register this product at

www.conair.com/registration

Service Center

Conair Corporation

Service Department

7475 North Glen Harbor Blvd.

Glendale, AZ 85307

150 Milford Road, East Windsor, NJ 08520

7475 North Glen Harbor Blvd., Glendale, AZ 85307

14PG006835 IB-13112

Once again, thanks for buying a

Conair product.

Your Conair® clipper blades are made of stainless

steel. They are engineered for precise, professional

results. If blades feel like they are pulling or

grabbing hair, it means they are losing their

sharpness and should be replaced as soon as

possible.

Comb attachments should also be replaced if they

are lost or broken. It is easier to cut hair with the

accuracy of a pro when the necessary tools are at

your fingertips.

Conair makes a variety of accessories for different

haircut kits. If your haircut kit does not include

them, you may want to consider adding them to

your professional haircutting tools.

Left and right ear comb attachments provide

effortless, precise cutting around the ears. Styling

clips hold hair in place when you are sectioning

hair. A styling comb makes it easy to taper or

cut hair at an angle. A barber cape ensures a

comfortable and neat haircut, and a convenient

storage pouch keeps all your essentials in

one place.

Model HC500

COMB-4

Model HC500

COMB-3

Model HCNB-1

Model CAPE-1

Model SC-1

Model HC500

BLD-2

Model HC500

BLD-1

Model HC500

COMB-2

Model HC OIL

Model CLP- 1

Model HC500

COMB-1

CUT HERE

HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM

Pricing in effect through December 31, 2015. Orders postmarked after this date

will be accepted, and the customer will be notified if pricing has changed.

ITEM PART # PRICE QUANTITY AMOUNT

Clipper Blade Set HC500-BLD1 $6.50

Trimmer Blade Set HC500-BLD2 $6.50

4 Attachment Combs (1/8 , 1/4 , 3/8 , 1/2"""")

HC500-COMB1 $5.00

3 Attachment Combs (5/8 , 3/4 , 7/8 ) """ HC500-COMB2 $5.00

1" Attachment Comb HC500-COMB3 $2.00

Left/Right Ear Attachment Combs HC500-COMB4 $2.00

Neck Brush HCNB -1 $1.50

Deluxe Vinyl Cape CAPE-1 $5.00

Lubricating Oil (pkg of 3 tubes) HC OIL $2.00

Barber Scissors SC-1 $2.00

Styling Clips (set of 3) CLP-1 $1.50

Subtotal

Enclose check or money order made payable to Conair. (We cannot accept cash, stamps Sales Tax*

or C.O.D. orders.) *CT, IL, AZ, and PA residents should add applicable state sales tax.

Minimum order of $10.00 or a $2.00 handling charge will be added to order. TOTAL

All prices include handling and return postage. Prices are subject to change

without notice. Prices are valid only for shipments within the continental United States.

Mail to:

Please allow 4–6 weeks for delivery. Conair Corporation

Service Department

To avoid delays, please print clearly. 150 Milford Road

We must have a street address, as UPS cannot deliver to a P.O. box. East Windsor, NJ 08520-9730

NAME _________________________________________________________________________________________________

ADDRESS APT. ___________________________________________ ______________________________________________

CITY ________________ STATE_______ ZIP ________________________________________________ ________________

TELEPHONE ( ) ___________________________________________________________

(We call only if we have a question about your order.)

For information on other Conair haircut kit parts call: 1-800-3-CONAIR.

Produkt Specifikationer

Mærke:	Conair
Kategori:	Ikke kategoriseret
Model:	HCT45N

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair HCT45N stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Conair Manualer

Conair NPTCCA01 Manual

10 December 2024

Conair True Glow PB8NPRF Manual

10 December 2024

Conair NPTCCA02 Manual

10 December 2024

Conair MiniPRO CS80N Manual

1 Oktober 2024

Conair MASK2 Manual

1 Oktober 2024

Conair skn SFB11GK Manual

1 Oktober 2024

Conair Man GMTL6000 Manual

6 September 2024

Conair LNT1 Manual

6 September 2024

Conair Man GMT189R Manual

6 September 2024

Conair InfinitiPRO 998 Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg KIT6PX Manual

23 December 2024

Smeg KIT6CX Manual

23 December 2024

Smeg GTA-6 Manual

23 December 2024

Lucide Casper i 79166/19/12 Manual

23 December 2024

Lucide Merlina 78193/30/66 Manual

23 December 2024

Lucide Pippa 77583/81/30 Manual

23 December 2024

Lucide Pia 45380/04/30 Manual

23 December 2024

Lucide Pia 45280/01/30 Manual

23 December 2024

Lucide Anaka 45179/03/30 Manual

23 December 2024

Lucide Zych 45156/01/97 Manual

23 December 2024