Conair InfinitiPRO S9900 Manual

Conair Ikke kategoriseret InfinitiPRO S9900

Læs nedenfor 📖 manual på dansk for Conair InfinitiPRO S9900 (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

HYDRO

FUSION

STEAM STRAIGH TENER

Instruction and Styling Guide

For your safety and continued enjoyment

of this product, always read the instruction

book carefully before using.

Model S9900

IMPORTANT SAFETY

INSTRUCTIONS

While emitting steam, this appliance may cause

burns if it is used too close to the skin, scalp or

eyes or if it is used incorrectly. To reduce the

risk of contact with hot water emitting from the

steam vents, test this appliance before each use

by holding it away from the body and closing

the plates prior to selecting the steam function.

When using electrical appliances, especially

when children are present, basic safety

precautions should always be taken, including

the following:

READ ALL

INSTRUCTIONS

BEFORE USING

KEEP AWAY

FROM WATER

DANGER – Any appliance is electrically

live even when the switch is off. To reduce the

risk of death by electric shock:

1. Always unplug appliance immediately

after using.

2. Do not use while bathing or in the shower.

3. Do not place or store appliance where it can

fall or be pulled into a tub or sink.

4. Do not place in or drop into water or

other liquids.

5. If an appliance falls into water, unplug it

immediately. Do not reach into the water.

WARNING – To reduce the risk of

burns, electrocution, fire, or injury to persons:

1. This appliance should never be left

unattended when plugged in.

2. Do not pull, twist, or wrap line cord

around appliance.

3. This appliance should not be used by, on,

or near children or individuals with certain

disabilities.

4. Use this appliance only for its intended

use, as described in this manual. Do not

use attachments not recommended by the

manufacturer.

5. Never operate this appliance if it has a

damaged cord or plug, if it is not working

properly, or if it has been dropped, damaged,

or dropped into water. Return the appliance

to an authorized service center for

examination and repair.

6. Keep the cord away from heated surfaces.

7. Never use while sleeping.

8. Never drop or insert any object into

any opening.

9. Do not use outdoors or operate where aerosol

(spray) products are being used

or where oxygen is being administered.

10. Unit is hot when in use. Do not let heated

surfaces touch eyes or skin.

11. Do not place the heated unit

directly on any surface while it is hot

or plugged in.

12. Never block the air openings of the

appliance or place it on a soft surface, such as

a bed or couch, where the air openings may be

blocked. Keep the air openings free of hair, lint,

and other debris.

13. Do not use an extension cord with

this appliance.

14. Do not touch hot surfaces of the appliance.

Use handles or knobs.

15. Do not attempt to touch the housing of your

appliance near the straightening plates, as it is

hot when in use.

16. Do not use with a voltage converter.

17. This appliance is not a toy. Keep away

from children.

18. Fill reservoirs with water only.

19. While emitting steam, this appliance may

cause burns if it is used too close to the skin,

scalp, or eyes or if it is used incorrectly.

20. To reduce the risk of contact with hot

water emitting from the steam vents, test this

appliance before each use by holding it away

from the body and closing the plates prior to

selecting the steam function.

SAVE THESE

INSTRUCTIONS

OPERATING

INSTRUCTIONS

This appliance is intended for household use.

Use on Alternating Current (60 hertz) only. This

unit is designed to be operated at 120 volts AC.

This appliance has a polarized plug (one blade

is wider than the other). As a safety feature,

this plug will fit in a polarized outlet only one

way. If the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit, contact

a qualified electrician. Do not attempt to defeat

this safety feature.

NOTE: Do not use this styling appliance

on hair extensions.

INSTANT HEAT TECHNOLOGY

The iron’s 5 unique high temperature settings

and Instant Heat technology provide styling

versatility for all hair types. If you have fine hair,

a low temperature will provide the best results.

If you have thick, wavy, or hard-to-straighten

hair, keep the heat setting on high. You can vary

the iron’s temperature setting according to your

particular need.

Temperature Setting Guide

TEMP. CONTROL HAIR TYPE

285°F fragile hair

320°F ﬁne hair

355°F medium/normal hair

390°F wavy/curly hair

430°F thick/textured hair

This styling iron features a powerful heater that

maintains high temperatures during use for

precision styling. It heats up quickly to the

temperature you’ve selected for your hair type.

Conair’s professional salon standards of

engineering provide you with a uniform and

improved heat recovery system that maintains

the iron at constant temperatures. There is a

constant surge of power to ensure that heat is

continuously and quickly delivered for optimal

styling results, unlike other units, which lose

heat during use. This provides consistent styling

power so that every strand of your hair is set

with the same level of heat and comes out the

same way for a perfect finish.

Styling has never been easier with the new

Hydrofusion Steam Straightener with titanium

plates! Get ready to experience salon results

without the salon!

HYDROFUSION TECHNOLOGY

Discover the power of steam technology for

long-lasting straight hair with deep shine. With

every pass, a conditioning steam mist infuses

moisture and hydrates each hair cuticle for a

silky-smooth, healthy-looking finish.

Hydrofusion transforms all hair types and

textures and conditions for less damage

and long-lasting results.

You can choose to style with the steam function

switched on or off, and you can choose to refill

the straightener reservoir directly or use with

the base station for effortless gravity refill.

NOTE: When you first turn the straightener on,

the steam function will be off.

STYLING WITH THE NEW EASY-GLIDE,

FLOATING TITANIUM-COATED PLATES

Your new straightening iron has plates

designed with a little give to “float.” This

provides better contact with hair, eliminating

gaps, for straighter results. The easy-glide

titanium surface is one of the latest – and

best – technological advances in hair

appliances. The titanium, even-heat

distribution produces the ultimate in silky,

shiny, healthy-looking hair. You’ll find that

hair glides easily over the surface of the plates

as you’re straightening and that it is easier to

clean styling product residue off the plates after

each use. The titanium surface also helps

smooth down flyaways. As you smooth your

hair, heat is evenly distributed so that the style

you create has a salon-perfect, silky smooth,

shiny finish.

HOW TO FILL AND

USE STRAIGHTENER

To use the straightener without steam:

Simply press the button ( ) to turn your ON/OFF

straightener on.

To use the straightener with steam

and the base station gravity refill:

1. Before filling with water, be sure the black

rubber plug on the bottom of the base station is

tightly closed.

2. Lift the black rubber plug

on the top of the base station

water reservoir and fill

reservoir with distilled water.

NOTE: We recommend using

distilled water as this will

help protect the appliance

best and lessen the chance of clogging the

mechanism that allows the steam to flow.

The base station water reservoir holds 100 ml

of water and will provide around 60 minutes

of steam time with a full tank. Replace the

black rubber plug and ensure it’s tightly closed.

3. Place the base station onto a flat, level heat-

resistant surface and push down to secure the

suction feet onto the surface. This will prevent

the base station from moving around.

4. Ensure that the water

reservoir on the bottom of

the straightener is empty of

water and secured in place,

then place the straightener

onto the base station by

aligning the 2 pins and

pushing down until the straightener

clicks into place.

NOTE: there’s no need to close or lock the

plates – you can place the straightener onto

the base station with the plates in the open

position. However, if the straightener is

switched on, we recommend locking the plates

before placing the straightener onto the base

station to avoid the hot surfaces of the

straightener coming into contact with skin.

5. As soon as the straightener is correctly in

place, the water will automatically refill within

10-15 seconds. The straightener doesn’tNOTE:

need to be switched on to refill with water,

but, as mentioned above, if the if the

straightener is switched on, we recommend

locking the plates before placing the

straightener onto the base station.

6. Remove the straightener from the base

station and press the button (ON/OFF ) to turn

your straightener on. The default 285°F LED

indicator will illuminate and start to flash.

At this point, the straightener will start

heating up.

7. Press the Steam button ( ) once to switch

on the steam function. The steam LED indicator

will illuminate. When using the steam function

for the first time, the motor will run continuously

for 2 seconds after turning the unit on when the

plates are closed.

8. When using the steam function and the

plates are closed, the straightener will make a

clicking sound. This is completely normal and

part of standard operation, as the pump is

pushing the water through the inside

mechanism.

9. To refill the straightener water reservoir,

you can simply place the straightener onto

the base station between brushing and

sectioning your hair, being careful not to touch

the hot surfaces of the straightener. The refill

is effortless!

TIP: To avoid overfilling the straightener,

always ensure that the straightener water

reservoir is nearly or completely empty of

water before placing onto the base station

for refilling.

IMPORTANT: The base station should only

be used for refilling the straightener

water reservoir. Please do not rest the

straightener on the base station when

not in use.

10. Once you’ve finished styling your hair, be

sure to empty all of the water reservoirs:

a) base station water reservoir – empty water

from the top section of the base station by

lifting the black rubber plug on the top and

pouring the remaining water into a sink.

b) base station bottom tank – empty water

from the bottom section of the base station by

lifting the black rubber plug on the bottom and

pouring the remaining water into a sink.

c) straightener water reservoir – remove

the water reservoir from the bottom of the

straightener, lift the black rubber plug, and

pour remaining water into a sink.

To use the straightener with steam but

without the base station:

1. Remove the water

reservoir located at the

bottom of the straightener

by pushing the release

switch down with one

hand while removing the water reservoir with

the other hand.

2. Lift the black rubber plug and using the

pipette, fill with distilled water. NOTE: We

recommend using distilled water as this will

help protect the appliance best and lessen the

chance of clogging the mechanism that allows

the steam to flow. The straightener water

reservoir holds 10 ml of water and will provide

around 6 minutes of steam time with a full tank.

Replace the black rubber plug and put the

reservoir back on the straightener until it clicks

into place. Check that the reservoir is properly

positioned and secured in place.

3. Press the button (ON/OFF ) to turn your

straightener on. The default 285°F LED indicator

will illuminate and start to flash. At this point,

the straightener will start heating up.

4. Press the Steam button ( ) once to switch on

the steam function. The steam LED indicator

will illuminate.

5. If the plates are closed when using the steam

function, the straightener will make a clicking

sound. This is completely normal and part of

standard operation, as the pump is pushing the

water through the inside mechanism.

ALWAYS remove excess water from the base

station water reservoir…the base station

bottom tank…and the straightener water

reservoir after use, since leaving unused

water in the reservoirs can cause clogging

over time.

NOTE: NEVER add any other liquid aside from

distilled water to the water reservoirs.

CAUTION: This is a high-heat appliance.

Care must be taken to avoid the hot surfaces

of the appliance coming into contact with skin

(e.g., scalp, neck, ears, face, etc.), as the plates

can, particularly if held too close, cause

discomfort or even burn.

GETTING STARTED

1. Fill either the base station water reservoir

or the straightener water reservoir with

distilled water, following the instructions on

the previous pages.

2. Place the straightener onto a flat, level

heat-resistant surface.

3. Plug your straightener into a 120V AC

power outlet.

4. Press the button ( ) to turn yourON/OFF

straightener on. The default 285°F LED indicator

will illuminate and start to flash. At this point,

the straightener will start heating up.

5. Press the Temperature button (+/-) to adjust

to your desired temperature. The temperature

LED indicator will illuminate and start to flash.

Once the temperature you have selected has

been reached, it will then stop flashing on

the display.

6. If using the steam function, press the

Steam button ( ) once to switch on the

steam function. The steam LED indicator

will illuminate.

7. If the plates are closed when using the steam

function, the straightener will make a clicking

sound. This is completely normal and part of

standard operation, as the pump is pushing the

water through the inside mechanism.

WARNING: The flat iron's titanium plates

will get very hot within a few seconds and

should not come into contact with skin after

the flat iron has been turned on.

TO STYLE HAIR

Hair should be clean and completely dry before

using the flat iron. For best results, use a light

styling product before blow-drying hair.

1. Start with a hair section that is 1½ inches

wide and no more than ½ inch thick.

2. Open the iron and place the hair section

between the two hot plates close to the

scalp. Trap hair between the plates by firmly

squeezing the handles together.

3. While maintaining the tension, slowly pull

the unit down along the hair section toward the

ends. At the ends, release the pressure on the

handle and allow the hair to slide out.

4. Repeat the process on additional sections of

hair until you achieve the hairstyle you desire.

It may be necessary to repeat the process on

certain areas, depending on the texture of

your hair.

Some experience is necessary when learning

to use this flat iron. After using the iron several

times, you will learn the ideal way to straighten

and style your hair.

VOLUME

Create volume by making a curved movement

with your wrist as you glide the straightener

down the hair section.

EXPERT TIP

Set your style with a spritz of light-hold

hairspray for extra hold if needed.

REMOVABLE DETANGLING COMB

The flat iron includes a detangling comb that

helps to provide more uniform results and helps

to section and detangle as you style. The comb

is useful for helping to straighten hard-to-style,

coarse, and textured hair

types, as it creates more

tension as you straighten.

The comb is easily

removable – simply slide it

along the plate to the left to fully remove.

AUTOMATIC SHUTOFF

This straightener has an automatic shutoff

feature for added safety. If the straightener

is switched on for more than 30 minutes

continuously, it will automatically switch off.

If you wish to continue using the straightener

after this time, simply press the ON/OFF button

( ) again to turn the power on.

GET TO KNOW YOUR STEAM

STRAIGHTENER

Steam vents on

bottom plate

Removable

detangling comb

Base station with

water reservoir

Hinge lock

1½ in.* wide

straightening plates

5 heat settings

with LED indicator

Conditioning steam

LED indicator

Temperature adjustment button

Steam but ton

ON/OFF button

Water reservoir

Water reservoir release switch

* Actual plate width is 36 mm

Floating titanium-

coated plates

USER

MAINTENANCE

Your appliance is virtually maintenance free.

No lubrication is needed. Keep all vents and

openings clear of dirt and dust. If cleaning

becomes necessary, disconnect the unit from

the power source, allow it to cool, and wipe

exterior with a cloth. If any abnormal condition

occurs, unplug the unit, allow it to cool, and

return it for repair to an authorized service

representative only. No repairs should be

attempted by the consumer.

CAUTION

NEVER allow the power-supply cord to be

pulled, twisted, or severely bent. Never wrap

the cord tightly around the appliance. Damage

will occur at the high flex point of entry into

the appliance, causing it to rupture and short

circuit. Inspect the cord frequently for damage.

Stop use immediately if damage is visible or if

unit stops or operates intermittently.

STORAGE

When not in use, your iron is easy to store.

Allow appliance to cool, then simply store out

of reach of children in a safe, dry location. Do

not jerk or strain cord at plug connections.

Do not wrap the line cord around the appliance.

Allow the cord to hang or lie loose and straight

at the point of entry into the appliance.

FEDERAL COMMUNICATIONS

COMMISSION NOTICE

WARNING: Changes or modifications to this unit

not expressly approved by the party responsible

for compliance could void the user’s authority to

operate the equipment.

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions: (1) This device may not cause

harmful interference, and (2) This device must

accept any interference received, including

interference that may cause undesired

operation.

NOTE: This equipment has been tested and

found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user

is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

SUPPLIER’S DECLARATION

OF CONFORMITY

Brand: InﬁnitiPRO by Conair®

Model No.: S9900

Description: Steam Straightener

Responsible Party: Conair LLC,

1 Cummings Point Road,

Stamford, CT 06902 (203) 351-9000

Standards: FCC Part 15 Subpart B,

ANSI C63.4-2014

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful

interference, and (2) This device must accept

any interference received, including interference

that may cause undesirable operation.

DATE OF ISSUE: 03/18/2022

WARNING:

IF YOU THINK THE

POWER IS OFF WHEN

THE SWITCH IS OFF,

YOU’RE WRONG.

KEEP AWAY FROM WATER

Everyone knows that electricity and water are a

dangerous combination. But did you know that

an electric appliance is still electrically live even

if the switch is off? If the plug is in, the power

is on. So when you are not using your appli-

ances, keep them unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES

LIMITED THREE-YEAR WARRANTY

(U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your

unit free of charge for 36 months from the

date of purchase if the appliance is defective in

workmanship or materials.

To obtain service under this warranty, return the

defective product to the service center listed

on back, together with your purchase receipt.

California residents need only provide proof of

purchase and should call 1-800-3-CONAIR for

shipping instructions. In the absence of a pur-

chase receipt, the warranty period shall be 36

months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS,

OR LIABILITIES, INCLUDING BUT NOT

LIMITED TO THE IMPLIED WARRANTY OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL BE LIMITED IN

DURATION TO THE 36-MONTH DURATION OF

THIS WRITTEN, LIMITED WARRANTY. Some

states do not allow limitations on how long an

implied warranty lasts, so the above limitations

may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES FOR BREACH OF

THIS OR ANY OTHER WARRANTY, EXPRESS

OR IMPLIED, WHATSOEVER. Some states do

not allow the exclusion or limitation of special,

incidental, or consequential damages, so the

above limitation may not apply to you.

This warranty gives you specific legal rights,

and you may also have other rights, which vary

from state to state.

BEAUTY TIPS:

To achieve the looks you love and

for more great InﬁnitiPRO by Conair®

products, visit www.conair.com

Service Center

Conair LLC

Service Department

7475 N. Glen Harbor Blvd.

Glendale, AZ 85307

Please register this product at

www.register.conair.com

For information on any Conair

® or InfinitiPRO by

Conair® product, call 1-800-3-CONAIR or visit us on

the web at www.conair.com

22PA083335 IB-17638

Produkt Specifikationer

Mærke:	Conair
Kategori:	Ikke kategoriseret
Model:	InfinitiPRO S9900

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair InfinitiPRO S9900 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Conair Manualer

Conair MiniPRO CS80N Manual

1 Oktober 2024

Conair MASK2 Manual

1 Oktober 2024

Conair skn SFB11GK Manual

1 Oktober 2024

Conair Man GMTL6000 Manual

6 September 2024

Conair LNT1 Manual

6 September 2024

Conair Man GMT189R Manual

6 September 2024

Conair InfinitiPRO 998 Manual

3 September 2024

Conair CD117NN Manual

2 September 2024

Conair LLT2 Manual

2 September 2024

Conair CLS1X Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron Overbridge Manual

26 November 2024

Elektron Sidstation Manual

26 November 2024

SKROSS World Adapter Pro+ Manual

26 November 2024

SKROSS PRO – World & USB Manual

26 November 2024

SoundTube IPD-RS82-EZ Manual

26 November 2024

Kramer 4x1VB Manual

26 November 2024

Kramer RC-63A Manual

26 November 2024

SoundTube IPD-HP82-EZ Manual

26 November 2024

Kramer RK-KVM-1U-PP3 Manual

26 November 2024

Gioteck VX-2 (PS3) Manual

26 November 2024