Conair Number Cut HC355 Manual

Conair Ikke kategoriseret Number Cut HC355

Læs nedenfor 📖 manual på dansk for Conair Number Cut HC355 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

NUMBER CUT®

CORD/CORDLESS

Instructions for Care and Use

Respect the Ritual ®

HC355 Models

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, especially

when children are present, take basic safety

precautions, including the following:

READ ALL INSTRUCTIONS

BEFORE USING

KEEP AWAY FROM

WATER

DANGER – Any appliance is

electrically live, even when the switch is off.

To reduce the risk of death or injury by

electric shock:

1. Unplug this appliance before cleaning.

2. Do not place or store appliance where it can

fall or be pulled into a tub or sink.

3. Do not use while bathing or in the shower.

4. Do not place in or drop into water or

other liquids.

5. Do not reach for an appliance that has fallen

into water. Unplug immediately.

6. Except when charging, always unplug this

appliance from electrical outlet immediately

after using.

WARNING – To reduce the risk of

burns, electric shock, fire, or injury to persons:

1. Except when charging, this appliance should

never be left unattended when plugged in.

2. This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they

have been given supervision or instruction

concerning the use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with

the appliance.

3. Use this appliance only for its intended

purpose as described in this manual. Do not

use attachments not recommended by the

manufacturer. Do not use an extension cord

to operate this appliance.

4. Never operate this appliance if it has a

damaged cord or plug, if it is not working

properly, if it has been dropped or damaged,

or if it has been dropped into water. Return

the appliance to a Conair® service center for

examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any

opening on this appliance.

7. Keep air openings free of lint, hair and similar

debris.

8. Do not use this appliance with a damaged

or broken comb or with teeth missing from the

blades, as injury may occur.

9. Do not use outdoors or operate where aerosol

(spray) products are being used or where

oxygen is being administered.

10. Never operate the appliance with the air

openings blocked or while on a soft surface,

such as a bed or couch, where the air openings

may be blocked.

11. Always attach plug to appliance first, then

to outlet. To disconnect, turn all controls to OFF

then remove plug from outlet.

12. Do not pull, twist or wrap the cord around

the appliance.

13. When using the appliance with its cord, be

mindful of tangles or kinks in the cord. If the

cord does become tangled during use, turn

the unit off and straighten cord before

operating again.

14. THIS PRODUCT IS FOR HOUSEHOLD

USE ONLY.

15. This appliance is not a toy. Keep away

from children.

SAVE THESE

INSTRUCTIONS

USER MANUAL

Before using the Class 2 Power Supply,

read these instructions carefully.

Use with adapter: CA10

Rated input voltage: 100-240V AC,

50/60Hz 0.2A

Rated output: 3.0V DC, 1000mA

OPERATION

1. For dry location use only. Do not expose

to water.

2. When not in use, unplug unit completely.

3. Unit will become warm during operation.

CAUTION

1. Risk of electric shock, dry location use only.

Do not expose to liquid, vapor or rain.

2. Do not short the polarity (output cord). Ensure

jack is plugged into the clipper unit before

plugging the adapter into the outlet.

3. Do not operate any appliance that has a

damaged output cord or housing.

4. Always unplug the unit before cleaning or

when not in use, except when charging.

5. The adapter is intended to be correctly

oriented in a vertical or floor-mount position.

6. Be sure voltage is correct before plugging in.

For connection to a power supply not in the

U.S.A., use an attachment plug adapter of the

proper configuration for the power outlet.

FEDERAL COMMUNICATIONS

COMMISSION NOTICE

WARNING: Changes or

modifications to this unit not expressly approved

by the party responsible for compliance

could void the user’s authority to operate the

equipment.

NOTE: This equipment has been tested and

found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/ TV

technician for help.

SUPPLIER'S DECLARATION

OF CONFORMITY

Brand: CONAIRMAN®

Model No.: HC355

Description: Clipper

Responsible Party: Conair LLC,

1 Cummings Point Road,

Stamford, CT 06902 (203) 351-9000

Standards: FCC Part 15 Subpart B,

ANSI C63.4-2014

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful

interference, and (2) This device must accept

any interference received, including interference

that may cause undesirable operation.

DATE OF ISSUE: September 22, 2022

TROUBLESHOOTING

If your rechargeable clipper does not seem

to be taking a charge, take the following

troubleshooting steps before returning it for

repair:

1. Be sure the electrical outlet is working by

plugging in another appliance to test the outlet.

2. Make sure the electrical outlet is not

connected to a switch that turns power off

when lights are turned off.

OPERATING

INSTRUCTIONS

This appliance is intended for household use. It

includes an adapter to be used with 100-240V AC,

50/60Hz.

1. Before using the clipper for the first time,

charge continuously for 12 hours. Maximum

battery capacity will only be reached after 3

charging and discharging cycles.

2. After use, turn the switch to position.OFF

Recharge battery by connecting the charging

jack into the receptacle at the end of the clipper

and plugging the adapter unit into the electrical

outlet. The charging indicator will light up to

indicate that charging has begun.

3. After recharging, store in a dry place, away

from small children.

4. Do not wrap cord around the clipper.

5. Preserving the battery: n order to maintainI

the optimum capacity of the rechargeable

battery, the clipper should be recharged for

12 hours approximately every 6 months.

FOR DIRECT PLUG-IN OPERATION

1. Connect the charging jack into the receptacle

at the end of the clipper.

2. Plug the adapter unit into the electric outlet.

3. Turn the switch to position and let theOFF

clipper charge for a few minutes.

4. Turn the switch to position.ON

5. Unplug the adapter unit after use.

6. After use, store in a dry place away from

small children.

7. Do not wrap cord around the clipper.

8. This power unit is intended to be correctly

oriented in a vertical or floor-mount position.

THE CONAIR GUIDE

TO CUTTING HAIR AT HOME

Your new Conair® 16-Piece Number Cut®

Home Grooming Kit has everything you need

to achieve professional haircuts at home. The

powerful DC motor clipper with stainless steel

blades for long-lasting cutting precision features

a new 5-position adjustable taper control.

What ever hair length you set the lever for, the

clipper will automatically cut all hair in that

section at the same desired length.

Also included are 8 number-coded comb

attachments for different hair lengths, a barber

comb, a cleaning brush, scissors, lubricating

oil, a storage case, a blade guard for easy

maintenance of the clipper blades and

an adapter.

Please note that with the easy-to-use

number-coded combs, you can easily

remember your favorite combs once you

start to use them on a regular basis.

Before you start:

1. Inspect your clipper to make sure it is free

of hair and dirt, properly oiled and running

smoothly.

2. Place a towel or cape around the neck of the

person getting the haircut.

3. Seat the person so that his/her head is at your

eye level. This gives you greater visibility and

control.

4. Comb hair until it is tangle free. Hold the

clipper in a comfortable grip. Now you’re ready

to cut.

MEDIUM-TO-LONG CUT

To begin, cut only a small amount of hair until

you become used to the length each attachment

leaves the hair. Try the longest attachment on the

clipper first. If you want a shorter cut, you can

then use shorter combs.

• Short attachment comb (number 1)

cuts hair to 1/8" (3mm).

• Medium-Short attachment comb (number 2)

cuts hair to 1/4" (6mm).

• Medium-Long attachment comb (number 3)

cuts hair to 3/8" (9.5mm).

• Long attachment comb (number 4)

cuts hair to 1/2" (12.5mm).

• Long attachment comb (number 5)

cuts hair to 5/8" (16mm).

• Long attachment comb (number 6)

cuts hair to 3/4" (19mm).

• Long attachment comb (number 7)

cuts hair to 7/8" (22mm).

• Long attachment comb (number 8)

cuts hair to 1" (25mm).

Attach comb by

holding it teeth up,

then snapping onto the

bottom of the clipper

blade.

NOTE: Never push

or shove the clipper

through the hair to

make it move more

quickly. Pro fes-

sional experience

shows that the

clipper works most

efficiently when

used at a moderate

pace.

To remove comb attachment, place index finger

and thumb as illustrated; then pull out and up.

To begin cutting hair:

1. The hair should be combed

in its natural direction.

2. Using the longest comb

attachment, trim sides from

the bottom upward. Hold

clipper lightly against the

hair with teeth of the comb

attachment pointing up ward

yet flat against the head.

Gradually lift the clipper

upward and outward through

the hair, trimming just a little

at a time.

Repeat around sides and

back of head.

If you want hair to be even

shorter:

A) Apply more pressure to the head with the

comb attachment that is in place. This takes

a little practice, of course. B) Switch to aOR

shorter comb attachment.

Remember, it’s better to leave

too much hair than too little.

For longer hair on top, use the

barber comb and lift hair on

the top of the head, cutting

over the comb. Or hold the

hair between the fingers and

cut to desired length. Always working from the

front to the back of the head, gradually cut the

hair shorter by reducing the space between

the comb or fingers and the head. Comb often

to check for uneven strands and to get rid of

trimmed hair.

OUTLINING

Outlining requires no

attachments. Comb hair into

the desired style. Position the

clipper between the sideburns

and the ear (see illustration),

making sure the corner edge

of the blade is against the

hairline. With the outline of the

hair as your guide, slowly move

the clipper over, around and

behind the ears. For the back

of the neck and the sideburns,

hold the clipper against the skin at the length

desired, move the clipper downward.

STOP. COMB. CHECK.

For best results, do what the professionals do:

Comb hair often and check clipping results as

you comb. This way you avoid uneven sides,

bangs, neckline, etc.

SHORT CUTS TO PERFECT

FLATTOPS, CREW CUTS, ETC.

Always cut from the back of the neck to the

crown, using the longest comb setting.

Hold the comb attachment flat against the head

and slowly move the clipper up through the hair.

Use the same technique for

the sides, cutting from the

bottom to the upper side of

the head.

For the front to the crown, cut

the hair against the direction

in which it grows. Then

even it up with the sides.

For a flattop, use the

flat comb, not the comb

attachment. Just cut hair

on top of the head over flat

comb (see illustration).

5-DETENT TAPER CONTROL

Just like levers on

professional clippers,

the Conair taper lever

is positioned at your

thumb so you can hold

the clipper in your hand

and adjust the lever at

the same time... while

you’re clipping. This taper lever eliminates the

need in some situations for an attachment comb

because it lets you gradually adjust the closeness

of the cut. For the closest cut and the shortest

hair, push taper lever up as far as it will go to

level #1. To increase cutting length, slowly push

lever down. If you push to the lowest position,

level #5, it will leave hair about the same length

as the short attachment comb.

Close Cut

Longer

Cut

Because a different cutting edge is used in each

setting, using the taper lever lengthens the life

of your blades. Packed-in hair can slow down

any clipper. To remove hair, without removing the

blades, take your cleaning brush and brush the

hair from the blades. If you do this after every

clipping, especially with heavy haircutting, the

blades should remain free of cut hair. If clipper

stops cutting and this action doesn’t help, you

might have to loosen the blades to remove the

hair.

BATTERY SAFETY INFORMATION

1. This device requires one nickel metal hydride

battery.

2. Battery is not to be removed by the consumer

unless instructed by the manufacturer.

3. Since the battery is sensitive to high

temperatures, when storing the device, keep it in

a cool, dry place.

4. Never put batteries into a fire.

5. Switch off device after use.

6. Keep batteries away from children, especially

the batteries that are small enough to ingest.

7. If a battery is ingested, seek immediate

medical help.

8. Never open, crush, puncture or disassemble a

battery.

9. Dispose of battery according to any state and

local regulations.

10. Do not dispose of rechargeable battery as

solid waste.

BATTERY DISPOSAL

This appliance contains a nickel metal hydride

battery. To protect the environment, this

appliance and its battery must be disposed of

safely. DO NOT throw this appliance/battery in

the municipal waste system. At the end of its

life, please take this appliance to a recycling

center, where the internal rechargeable

battery should be removed by a professional

and recycled separately. For more information

about the recycling of electrical and battery-

operated appliances, please contact your local

recycling or environmental protection ofﬁce or

your household waste disposal service.

For speciﬁc questions regarding replacement

of the battery in this product, please

call our Conair Customer Care Line at

1-800-3-CONAIR.

To ﬁnd the nearest drop-off recycling location,

call 1-800-822-8837 or

visit www.call2recycle.org/locator/

CONTAINS NICKEL METAL HYDRIDE

BATTERY. MUST BE COLLECTED,

RECYCLED OR DISPOSED OF

PROPERLY. DO NOT DISPOSE OF

IN THE MUNICIPAL WASTE.

BATTERY REMOVAL

INSTRUCTIONS

1. Using a small Phillips screwdriver, remove

the screws on the bottom housing at back of

the clipper.

2. Remove the top housing by hand.

3. Now the battery is exposed so you can separate

the wire connectors. Carefully hold the wires on

each side of the connector and gently cut the

wires. The connector will separate and the battery

can be removed from the inner housing.

3 Screws

Battery

Carefully cut

here with

wire cutters

to remove

battery

USER

MAINTENANCE

INSTRUCTIONS

CARE OF YOUR CLIPPERS

DETACHABLE BLADE SET

Your clipper is equipped with a detachable

blade set for routine maintenance, cleaning

and replacement.

Fig. 1

Fig. 2

To remove the blade: The

front of the clipper should

be facing you. Then push

up under the blade with

your thumb and the blade

will pop out. (See Fig 1.)

To replace the blade: Make

sure the taper control is

set to the longest position

and with the back of the

clipper facing you, insert

the bottom side of the

blade (with screws) into the

clipper and push down until

it snaps into place. (See Fig 2.)

OILING THE BLADES

(OIL INCLUDED)

1. Oil the blades once a month

2. Turn the appliance on.

3. Hold and point the blades downward.

4. Spread one drop of oil across the blades.

5. Turn the clipper off and wipe away any

excess oil.

NOTE:

1. Do not over-oil the blades, as this can

damage the motor.

2. Do not oil the motor bearing, as it is

permanently lubricated.

3. KEEP OIL AWAY FROM CHILDREN.

Any other servicing should be performed by

an authorized service representative. This

appliance has no user-serviceable parts. The

product is for household use.

STORAGE

When not in use, your clipper should be

disconnected, allowed to cool and stored in a

safe, dry location, out of reach of children.

NOTE: Never pull on the clipper cord. Never

twist or wrap the cord around the clipper. Lay it

flat with the cord coiled up when not in use.

WARNING:

IF YOU THINK

THE POWER IS OFF

WHEN THE

SWITCH IS OFF,

YOU’RE WRONG.

KEEP AWAY

FROM WATER

Everyone knows that electricity and water are a

dangerous combination. But did you know that

an electric appliance is still electrically live even

if the switch is off? If the plug is in, the power

is on. So when you are not using your appli-

ances, keep them unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES

LIMITED FIVE-YEAR WARRANTY

(U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your

unit free of charge for 60 months from the date

of purchase if the appliance is defective in

workmanship or materials.

To obtain service under this warranty, return the

defective product to the service center listed

on back, together with your purchase receipt.

California residents need only provide proof

of purchase and should call 1-800-3-CONAIR

for shipping instructions. In the absence of a

purchase receipt, the warranty period shall be

60 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS,

OR LIABILITIES, INCLUDING BUT NOT

LIMITED TO THE IMPLIED WARRANTY OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL BE LIMITED IN

DURATION TO THE 60-MONTH DURATION OF

THIS WRITTEN, LIMITED WARRANTY. Some

states do not allow limitations on how long an

implied warranty lasts, so the above limitations

may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES FOR BREACH OF

THIS OR ANY OTHER WARRANTY, EXPRESS

OR IMPLIED, WHATSOEVER. Some states do

not allow the exclusion or limitation of special,

incidental, or consequential damages, so the

above limitation may not apply to you.

This warranty gives you specific legal rights, and

you may also have other rights, which vary from

state to state.

Thank you for buying a Conair product.

Your Conair® clipper blades are made of

stainless steel. They are engineered for

precise, professional results. If blades feel

like they are pulling or grabbing hair, it means

they are losing their sharpness and should be

replaced as soon as possible.

Attachment combs should also be replaced if

they are lost or broken. It is easier to cut hair

with the accuracy of a pro when the necessary

tools are at your fingertips.

Conair makes a variety of accessories for

different haircut kits. If your haircut kit does not

include them, you may want to consider adding

them to your professional haircutting tools.

Left and right ear attachment combs provide

effortless, precise cutting around the ears.

Styling clips hold hair in place when you are

sectioning hair. A styling comb makes it easy

to taper or cut hair at an angle. A barber cape

ensures a comfortable and neat haircut, and

a convenient storage pouch keeps all your

essentials in one place.

Please register this product at

Service Center

Conair LLC

Service Department

7475 North Glen Harbor Blvd.

Glendale, AZ 85307

22PG085567 IB-17829

Produkt Specifikationer

Mærke:	Conair
Kategori:	Ikke kategoriseret
Model:	Number Cut HC355

Har du brug for hjælp?

Hvis du har brug for hjælp til Conair Number Cut HC355 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Conair Manualer

Conair MiniPRO CS80N Manual

1 Oktober 2024

Conair MASK2 Manual

1 Oktober 2024

Conair skn SFB11GK Manual

1 Oktober 2024

Conair Man GMTL6000 Manual

6 September 2024

Conair LNT1 Manual

6 September 2024

Conair Man GMT189R Manual

6 September 2024

Conair InfinitiPRO 998 Manual

3 September 2024

Conair CD117NN Manual

2 September 2024

Conair LLT2 Manual

2 September 2024

Conair CLS1X Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Native Instruments Plasma Manual

4 November 2024

Wagner 2K Smart Manual

4 November 2024

Moen EB500-E Manual

3 November 2024

Moen Aspen 5824CH Manual

3 November 2024

Luxman MQ-88uSE Manual

3 November 2024

Luxman CL-38uSE Manual

3 November 2024

Luxman CL-1000 Manual

3 November 2024

Moen Aspen 5802CH Manual

3 November 2024

Luxman SQ-38u Manual

3 November 2024

Moen Aspen 5818CH Manual

3 November 2024