Crestron Aspire IC5-W-T Manual

Crestron Højttaler Aspire IC5-W-T

Læs nedenfor 📖 manual på dansk for Crestron Aspire IC5-W-T (2 sider) i kategorien Højttaler. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
QUICKSTART DOC. 7390B (2034590) 12.12
Aspire™ In-Ceiling Speakers
quickstart guide
IC5, IC6, IC8
www.crestron.com
Specifications subject to
change without notice.
IC5, IC6, IC8
Mount/Remove Speakers
The in-ceiling speakers include three toggle clamps that simplify the mounting process. If the
grilles are mounted on the speakers, remove them before proceeding. (Refer to “Install/Remove
Grilles”, below.)
1. Connect the speaker cable wires to the spring terminals by pressing the top of the terminals
down and inserting the exposed strands into the hole. Make sure that the wires go to the +
+ – – (red coded) terminals, and the wires go to the (black coded) terminals.
2. With the toggle clamps turned inward, insert the speaker into the opening. As the three
screws on the front of the speaker are tightened, the toggle clamps first rotate into clamping
position (refer to the figure to the right) and then begin holding the speaker to the ceiling.
Tighten the screws until the speaker is secured; do not overtighten.
3. Speaker removal is accomplished by reversing the procedures given in steps 1 and 2
above.
a. Loosen the front screws to unclamp the speaker. Continue to loosen the screws until
the toggle clamps rotate inward.
b. When the speaker is loose, carefully remove it from the opening.
c. Disconnect the wires from the terminals.
Install/Remove Grilles
The zero-bezel frameless grilles are held in place by powerful magnets. To remove the grilles,
grip the edges and pull away from the speaker.
Paint the Speaker Grilles
Speaker grille painting should be done prior to mounting.
1. Carefully remove the material on the underside of the grilles and set them aside for
reinstallation. It may be necessary to use a knife or other sharp instrument to free an
edge of the material so it can be peeled away. Use care to avoid cutting or tearing the
material.
2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the
holes in the grilles.
3. Once the paint is dry, reinstall the material to the underside.
1
1
The product of expert Crestron® audio engineering,
Aspire™ speakers deliver high-end performance for
demanding residential installations. Select materials and
a refined appearance underscore the meticulous design
behind each model. The result is a complete line of
in-wall and in-ceiling speakers worthy of a place in every
room of the finest custom home.
The Aspire line strikes a perfect balance between
performance and price, delivering pristine, impactful
sound quality, with minimal impact on your décor thanks
to paintable zero-bezel grilles.
Rear View (Typical)
Front View (Typical)
Install Cables
Run the cables from the audio source to each speaker location following all appropriate
local codes. Strip the ends of the speaker cable wires 1/4” to 1/2” (6 mm to 12 mm) and
twist the exposed strands.
1Installation
Determine Placement In Room
90°
Prepare Mounting Holes
Speaker placement is largely a matter of personal preference. However, placing the speaker
near a corner or wall will extend its low frequency response.
Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air
ducts, joists, or other possible obstructions. Use a good quality stud finder to locate joists.
If there is no access to the area above the ceiling, and it is uncertain that there are no
obstructions, carefully drill a small hole just through the ceiling near the middle of the proposed
speaker location(s) and use one of the commercially available inspection devices designed for
this purpose, or do one of the following:
● Use a piece of stiff wire, bent into an “L” shape, with one end long enough to explore an
area equal to the size of the speaker with the toggle clamps extended. Insert the wire into
the hole, make sure it rotates freely in a complete circle and that there is sufficient depth,
or
● Use a drywall saw to cut a small hole at a 45° angle toward the inside of the hole. An
angle cut simplifies repair since the removed piece can be reinserted to help plug the hole.
If there are no obstructions, use the supplied template to trace outlines of the mounting holes
on the ceiling. Cut the final mounting holes at a 90° angle to the ceiling.
Tighten
Screws
Spring
Terminals (2)
Toggle
Clamps (3)
45°

Produkt Specifikationer

Mærke: Crestron
Kategori: Højttaler
Model: Aspire IC5-W-T

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron Aspire IC5-W-T stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Crestron Manualer

Crestron

Crestron ULTIMATE IC3-SA-WOOFER Manual

28 August 2024
Crestron

Crestron ULTIMATE IC3-AW-SA-BOX-WOOFER Manual

28 August 2024
Crestron

Crestron ULTIMATE IC3-AW-SA-TWEETER Manual

28 August 2024
Crestron

Crestron ULTIMATE IWS82-AW-W-T-EACH Manual

26 August 2024
Crestron

Crestron ULTIMATE IWLCR62-W-T-EACH Manual

26 August 2024
Crestron

Crestron ULTIMATE ICS8-AW-W-T-EACH Manual

25 August 2024
Crestron

Crestron SAROS ICT5T-22 Manual

25 August 2024
Crestron

Crestron ULTIMATE IC6-AW-W-T-EACH Manual

25 August 2024
Crestron

Crestron ULTIMATE IC8-AW-W-T-EACH Manual

25 August 2024
Crestron

Crestron Ultimate IGS12T-PRIMED-EACH Manual

23 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Nikkei

Nikkei NWS04 Manual

17 December 2024
Denon DJ

Denon DJ SM50 Manual

17 December 2024
Audac

Audac CIRA724I Manual

17 December 2024
Audac

Audac ATEO6M Manual

17 December 2024
Coastal Source

Coastal Source EB102W710BN Manual

17 December 2024
Coastal Source

Coastal Source B10SW8BN Manual

17 December 2024
Coastal Source

Coastal Source EB82W6.5BN Manual

17 December 2024
NGS

NGS WILD Space 2 Manual

17 December 2024
Canton

Canton Chrono SL 520.2 Manual

16 December 2024
Canton

Canton GLE 456 Center Manual

16 December 2024