Crestron CCS-UCA-SMK Manual

Crestron Videokonferencesystem CCS-UCA-SMK

Læs nedenfor 📖 manual på dansk for Crestron CCS-UCA-SMK (2 sider) i kategorien Videokonferencesystem. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

DO GUIDE

CCS-UCA-SMK

Swivel Mount Kit for Crestron Mercury™ Tabletop Conference System

DO Prepare the Mounting Location

NOTE: The mounting surface should have a thickness of 1" (25 mm) to 1-3/8" (34 mm).

The kit includes a template that is used to mark the location of the mounting hole on top of the mounting surface, and the location of the stop plate under the

mounting surface. When using the template, make sure the arrow on the template points toward the front edge of the mounting surface.

1. Secure the template to a mounting location that allows the full pivot of the device on the top of the mounting surface and a close mounting location for

accessories beneath the mounting surface.

2. Place 2" painters tape (not included) on the hole location and mark the hole on the tape.

3. Drill a 1-3/16" (30 mm) mounting hole in the marked location on the tape.

4. Relocate the template to the underside of the mounting surface and orient it so that the arrow on the template points toward the front edge of the table.

Verify that the template location of the stop plate permits the Crestron Mercury™ device to swivel.

DO Install the Cable Retention Bracket

NOTE: If a cable retention plate is already installed, it must be removed. For new installations, skip to step 3. Otherwise, follow this procedure:

1. Use two small at head screwdrivers to slowly pry off the existing retention plate.

2. Remove all adhesive residue from the surface.

3. Clean the surface with an alcohol wipe (not supplied).

4. Remove the paper liner from the back of the cable retention bracket.

5. Install the cable retention bracket as shown in the following diagram.

6. Press rmly on the cable retention bracket for approximately 30 seconds.

CAUTION: When turning over the device, place the device on a soft surface to avoid damage to the unit.

DO Connect the Device

1. Drill pilot holes with a 1/8" bit in the stop plate’s mounting location and attach the stop plate to the underside of the mounting surface with the six

included 8-8B x 1/2" screws.

2. Place the swivel tube plate on the mounting surface.

3. Route all cables that connect to the Crestron Mercury device from underneath the mounting surface through the swivel kit hardware as shown below.

Cables with larger connectors should be routed rst, followed by cables with smaller connectors.

If the HDMI® input cable and the USB cable are to be routed to the front of the Crestron Mercury device, do not route these cables through the swivel kit

hardware.

DO Check the Box

QUANTITY PRODUCT COLOR PART NUMBER

1 Bit, Slotted 1/4" W 2049730

1 Bit, Slotted 23/64" W 2049474

1 Bracket, Cable Retention 4526653

1 Cable, HDMI, Male to Female Extender 2049637

4 Insert, Metal, M7, 6-32 Thread, 0.28" L 2049476

2 Insert, Metal, M10, 10-32 Thread, 0.41" L 2049328

2 Nut, 1-1/8"-12 2049390

2 Screw, 4-40 x 1/4", Pan Head, Phillips Black 2007158

2 Screw, 6-32 x 1/2", Pan Head, Phillips Black 2007238

2 Screw, 6-32 x 1", Truss Head, Phillips Black 2049649

6 Screw, 8-8B x 1/2", Pan Head, Phillips 2017784

2 Screw, 8-32 x 1/8", Cap Head, Socket Black 2017634

2 Screw, 10-32 x 1", Pan Head, Phillips Black 2049391

1 Stop Plate, Swivel, with Screws 4526651

1 Template, Cutout 4526654

5 Tie Wrap 2047935

1 Washer, Cork, 2.0" OD, 1.19" ID, 0.06" TH 2049448

1 Washer, Keyed 4526609

1 Washer, Metal, 2.0" OD, 1.19" ID, 0.10" TH 2049389

1 Washer, Rubber, 2.0" OD, 1.19" ID, 0.06" TH 2049449

If the Crestron Mercury device’s HDMI OUT port is to be used, perform the following procedure:

a. Connect the HDMI Extension Cable (2049637) to the HDMI OUT port.

b. Route the cable extender through the swivel tube.

c. Connect the HDMI cable provided with the Crestron Mercury device to the cable extender.

4. Make the necessary connections to the device. Refer to the DO Guide or Installation Guide included with the Crestron Mercury system.

5. Use the included tie wraps to secure all of the cables to the cable retention bracket that was installed in “DO Install the Cable Retention Bracket.”