Crestron Saros ICE8T-W-T-EACH Manual

Crestron Højttaler Saros ICE8T-W-T-EACH

Læs nedenfor 📖 manual på dansk for Crestron Saros ICE8T-W-T-EACH (2 sider) i kategorien Højttaler. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
Saros® Express 2-Way In-Ceiling Speakers
quickstart guide
SAROS_ICE4T/ICE6T/ICE8T
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
SAROS_ICE4T/ICE6T/ICE8T
Set the Transformer Tap Selector Switch
The speakers are equipped with a 70/100 V matching transformer for distributed audio
systems. The transformer tap selector switch on the front panel is used to set the speaker
power level. Use a flat blade screwdriver to adjust the switch.
1. For SAROS_ICE4T and SAROS_ICE6T 70 V systems, use the left side settings and
select from 3.75, 7.5, 15, or watts. 30
2. For SAROS_ICE4T and SAROS_ICE6T 100 V systems, use the right side settings
and select from position should not be used.7.5, 15, or 30 watts. The X
3. For SAROS_ICE8T 70 V systems, use the left side settings and select from 7.5, 15,
30, or 60 watts.
4. For SAROS_ICE8T 100 V systems, use the right side settings and select from 15 30, ,
or 60 watts. The X position should not be used.
The switch may also be set to operation, bypassing the transformer completely. This 8Ω
setting should be used only for 8 Ω audio systems.
QUICKSTART DOC. 7496A (2037419) 11.13
1
1Installation
Saros® Express speakers by Crestron® deliver easy
installation and excellent performance in a range of
popular sizes for cost-sensitive commercial applications.
Ideal for use in background music, paging, and sound
reinforcement systems, Saros Express speakers are
engineered to achieve full, even coverage and clear
sound quality at a very affordable cost. Their zero-
bezel frameless grille achieves an unobtrusive and
contemporary appearance. Installing the grille requires
no hardware or tools, utilizing powerful magnets to hold
it in place. A safety tether is included to prevent the grille
from ever falling from the ceiling.
Saros Express speakers are available in white or black
and can be painted to blend with the ceiling surface.
Prepare Mounting Hole
Front View - Grille Removed
Tighten
Screws
70V 100V
IN
THRU
Terminal Block
Not Shown
Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air
ducts, joists, or other possible obstructions. If applicable, use a good quality stud finder to
locate joists. If there are no obstructions, use the supplied template to trace an outline of
the mounting hole.
For drop tile ceilings, remove the ceiling tile and place on a flat surface to trace the
mounting hole. For drywall or standard construction ceilings, use the template to trace the
mounting hole directly on the ceiling.
Install Cable
Run the cable from the audio source to the speaker location, observing all appropriate
local codes. Strip the ends of the speaker cables approximately 1/8” to 3/16” (~3 mm to
~5 mm) and twist the strands.
Install Tile Bridge
The included tile bridge components provide proper support when the speaker is installed
in a typical drop tile ceiling. Refer to the illustration below.
1. Based on the location of the mounting hole determined in “Prepare Mounting Hole”
above, use the two supplied screws to attach the support ring to the rails so that
when installed, the ring is aligned with the mounting hole and the rails rest on the
ceiling grid frame.
2. The support ring position on the rails is adjustable to enable off-center speaker
positioning. The tile bridge assembly can be folded to fit through the speaker cutout in
blind-mount situations.
Speaker Cable Connections
Screw
Cable
Clamp
Speaker
Cable
Terminal
Block
Mounting
Clips
Rear
Cover
Panel
Mount/Remove Speaker
The in-ceiling speaker includes four toggle clamps that simplify the mounting process. If the grille is mounted
on the speaker, remove it before proceeding. (Refer to “Install/Remove Grille” above.)
1. Referring to the illustrations to the right, remove the screw securing the rear cover panel, and lift the
cover panel off to expose the supplied terminal block.
2. Route the speaker cable through the cover cable clamp and connect the wires to the terminal block,
using the outer terminals: red to and black to . Use the inner and terminals to connect a IN + – + – THRU
pass-through (parallel) speaker.
3. Allow some slack in the speaker cable(s) and position the cover panel on the back, making certain it
engages the mounting clips. Secure the cover panel using the screw removed in step 1 and tighten the
cable clamp to secure the cable(s). Do not overtighten. Use a safety tether attached to the rear enclosure
to prevent the speaker from accidentally falling.
4. The toggle clamps offer two positions to accommodate both standard and extra thick surfaces up to
2.4 inches (61 mm). For extra thick tiles, reset the toggle clamps to the upper position before continuing.
a. With the toggle clamps turned inward, insert the speaker into the opening.
b. Hold the speaker against the ceiling and begin tightening the four screws on the front of the speaker.
The toggle clamps first rotate into clamping position (as indicated in the front view illustration to the
right) and then begin holding the speaker to the ceiling.
c. Tighten the screws until the speaker is secure. Do not over tighten.
5. Speaker removal is accomplished by reversing steps 1 through 4 above.
Tile Bridge Assembly
Install/Remove Grille
The zero-bezel frameless grille is held in place by powerful magnets. A safety tether is included to prevent
any possibility of the grille falling from the ceiling. With the tether attached, place the grille in position on
the speaker. To remove the grille, grip the edges and pull away from the speaker.
Paint the Speaker Grille
Speaker grille painting should be done prior to mounting.
1. Carefully remove the material on the underside of the grille and set it aside for reinstallation. It may be
necessary to use a knife or other sharp instrument to free an edge of the material so it can be peeled
away. Use care to avoid cutting or tearing the material.
2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the holes in the grille.
3. Once the paint is dry, reinstall the material to the underside.
Safety Tether
Rigging Points
For SAROS_ICE8T
100V70V
For SAROS_ICE4T,
and SAROS_ICE6T
100V70V
20.91 in
(531 mm)
Support
Ring
Screws
(Supplied)
25.92 in
659 mm

Produkt Specifikationer

Mærke: Crestron
Kategori: Højttaler
Model: Saros ICE8T-W-T-EACH

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron Saros ICE8T-W-T-EACH stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Crestron Manualer

Crestron

Crestron ULTIMATE IC3-SA-WOOFER Manual

28 August 2024
Crestron

Crestron ULTIMATE IC3-AW-SA-BOX-WOOFER Manual

28 August 2024
Crestron

Crestron ULTIMATE IC3-AW-SA-TWEETER Manual

28 August 2024
Crestron

Crestron ULTIMATE IWS82-AW-W-T-EACH Manual

26 August 2024
Crestron

Crestron ULTIMATE IWLCR62-W-T-EACH Manual

26 August 2024
Crestron

Crestron ULTIMATE ICS8-AW-W-T-EACH Manual

25 August 2024
Crestron

Crestron SAROS ICT5T-22 Manual

25 August 2024
Crestron

Crestron ULTIMATE IC6-AW-W-T-EACH Manual

25 August 2024
Crestron

Crestron ULTIMATE IC8-AW-W-T-EACH Manual

25 August 2024
Crestron

Crestron Ultimate IGS12T-PRIMED-EACH Manual

23 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Nikkei

Nikkei NWS04 Manual

17 December 2024
Denon DJ

Denon DJ SM50 Manual

17 December 2024
Audac

Audac CIRA724I Manual

17 December 2024
Audac

Audac ATEO6M Manual

17 December 2024
Coastal Source

Coastal Source EB102W710BN Manual

17 December 2024
Coastal Source

Coastal Source B10SW8BN Manual

17 December 2024
Coastal Source

Coastal Source EB82W6.5BN Manual

17 December 2024
NGS

NGS WILD Space 2 Manual

17 December 2024
Canton

Canton Chrono SL 520.2 Manual

16 December 2024
Canton

Canton GLE 456 Center Manual

16 December 2024