Crestron Saros PD4T-W-T-EACH Manual

Crestron Højttaler Saros PD4T-W-T-EACH

Læs nedenfor 📖 manual på dansk for Crestron Saros PD4T-W-T-EACH (2 sider) i kategorien Højttaler. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
Saros® Pendant Speakers
quickstart guide
SAROS_PD4T/PD6T/PD8T/PDS8T
www.crestron.com
Specifications subject to
change without notice.
SAROS_PD4T/PD6T/PD8T/PDS8T
Install/Remove Grille
The zero-bezel frameless grille is held in place by powerful magnets. A safety tether is
included to prevent any possibility of the grille falling from the ceiling. Attach the tether to the
baffle using the supplied screw, cover the screw with the rubber boot provided, and place the
grille in position on the speaker. To remove the grille, insert the supplied pick accessory in
one of the side edge grille holes and pull the grille away from the speaker. To remove the
grille completely, disconnect the monofilament tether from the speaker baffle.
Set the Transformer Tap Selector Switches
The speakers are equipped with a 70V/100V matching transformer for distributed audio
systems. The transformer tap selector switch on the front panel is used to set the speaker
power level. Use a flat-head screwdriver to adjust the switch.
• For SAROS_PD4T 70V systems, use the left-side settings and select from 1.88, 3.75,
7.5, 15, or 30 watts.
• For SAROS_PD4T 100V systems, use the right-side settings and select from 3.75,
7.5, 15, or 30 watts. The X position should not be used.
• For SAROS_PD6T, SAROS_PD8T and SAROS_PDS8T 70V systems, use the
left-side settings and select from 3.75, 7.5, 15, 30, or 60 watts.
• For SAROS_PD6T, SAROS_PD8T and SAROS_PDS8T 100V systems, use the
right-side settings and select from 7.5, 15, 30, or 60 watts. The X position should not
be used.
The switch may also be set to 8 Ω operation, bypassing the transformer completely. This
setting should be used only for 8 Ω audio systems.
QUICKSTART DOC. 7488B (2037418) 10.15
1
1Installation
Saros® speakers by Crestron® deliver professional grade
performance and flexible installation in a range of popular
sizes for demanding commercial applications. Solid
construction and high-end components are hallmarks of the
complete Saros speaker line.
Ideal for use in background or foreground music, paging,
and sound reinforcement systems, Saros speakers are
engineered to achieve smooth, even coverage, high output,
and clear, natural sound quality through the employment of
horn-loaded titanium dome tweeters, high-efficiency
damped cone woofers, ported enclosures, and precisely
tuned crossovers.
Front View - Grille Removed
Install Speaker Cable
Observe all local codes and install speaker cable from the audio source location to the
closest ceiling truss location where a speaker will be suspended, allowing sufficient length to
hang down slightly below the planned speaker height. If the speakers are to be connected in
parallel, install a second cable at that location and route it to the next speaker location.
Repeat this process at each speaker location.
Install Wire Rope
1. For each speaker to be installed, remove the top cover and route
the free end of one of the 15 ft (~5m) wire ropes supplied in the
SPKA-ST-15 Safety Tether/Tie Down Kit up through the top cover.
Connect the attached hook assembly to secure the wire rope to the
speaker rigging point.
2. Attach the free end of the wire rope to the ceiling truss, adjust the
length so the speaker is at the desired height, and secure it using
the supplied Gripple® wire rope grip. (Refer to the supplied
instructions for proper use of the Gripple.)
1. Refer to the illustration to the right, with the top cover off to expose the supplied
terminal block.
2. At each speaker location, route the speaker cable(s) hanging from the ceiling area
through the top cover, and dress the cables to the wire rope using plastic cable ties.
3. If using a supplied weather boot, slide the speaker cables through the weather boot.
Strip the ends of the cables approximately 1/8" to 3/16" (~3 mm to ~5 mm) and, if the
wire is stranded, twist the strands.
4. Connect the wires from the amplifier (or the previous speaker) to the supplied terminal
block, using the IN terminals; red to + and black to –. Use the THRU + and – terminals
to connect the speaker wires to the next (parallel) speaker.
5. Speaker removal is accomplished by reversing steps 1 through 4 above.
Paint the Speaker and Grille
Speaker and grille painting should be done prior to mounting.
1. Carefully remove the material on the underside of the grille, and set it aside for
reinstallation. It may be necessary to use a knife or other sharp instrument to free an
edge of the material so it can be peeled away. Use care to avoid cutting or tearing the
material.
2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the
holes in the grille.
3. Once the paint is dry, reinstall the material to the underside.
4. Remove the speaker top cover and paint the top cover and main speaker assembly
separately, being careful to mask areas that should not be painted.
100V
70V
For SAROS_PD6T/PD8T/PDS8T
100V70V
For SAROS_PD4T
100V70V
IN
THRU
Terminal
Block
Connect Speaker Cables
Speaker
Cables
Top
Cover
Speaker
Rigging Point
(Wire Rope Not
Shown)
Speaker
Rigging Point
Connect or Disconnect Speakers
NOTE: If the speakers are to be connected in parallel, the sum of the power settings
for all speakers must be less than the power amplifier’s power/channel rating.
Attach grille safety
tether with supplied
screw. Cover screw
with supplied rubber
plug.
Saros Pendant speakers include a top cover that conceals the wiring connections and suspension
hardware for a very clean, contoured appearance. The speakers are available in white or black and can
be painted to blend with the surrounding architecture.

Produkt Specifikationer

Mærke: Crestron
Kategori: Højttaler
Model: Saros PD4T-W-T-EACH

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron Saros PD4T-W-T-EACH stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Crestron Manualer

Crestron

Crestron ULTIMATE IC3-SA-WOOFER Manual

28 August 2024
Crestron

Crestron ULTIMATE IC3-AW-SA-BOX-WOOFER Manual

28 August 2024
Crestron

Crestron ULTIMATE IC3-AW-SA-TWEETER Manual

28 August 2024
Crestron

Crestron ULTIMATE IWS82-AW-W-T-EACH Manual

26 August 2024
Crestron

Crestron ULTIMATE IWLCR62-W-T-EACH Manual

26 August 2024
Crestron

Crestron ULTIMATE ICS8-AW-W-T-EACH Manual

25 August 2024
Crestron

Crestron SAROS ICT5T-22 Manual

25 August 2024
Crestron

Crestron ULTIMATE IC6-AW-W-T-EACH Manual

25 August 2024
Crestron

Crestron ULTIMATE IC8-AW-W-T-EACH Manual

25 August 2024
Crestron

Crestron Ultimate IGS12T-PRIMED-EACH Manual

23 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Nikkei

Nikkei NWS04 Manual

17 December 2024
Denon DJ

Denon DJ SM50 Manual

17 December 2024
Audac

Audac CIRA724I Manual

17 December 2024
Audac

Audac ATEO6M Manual

17 December 2024
Coastal Source

Coastal Source EB102W710BN Manual

17 December 2024
Coastal Source

Coastal Source B10SW8BN Manual

17 December 2024
Coastal Source

Coastal Source EB82W6.5BN Manual

17 December 2024
NGS

NGS WILD Space 2 Manual

17 December 2024
Canton

Canton Chrono SL 520.2 Manual

16 December 2024
Canton

Canton GLE 456 Center Manual

16 December 2024