CyberPower AVRG750LCD Manual

CyberPower Uafbrydelig strømforsyning (UPS) AVRG750LCD

Læs nedenfor 📖 manual på dansk for CyberPower AVRG750LCD (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne guide var nyttig for 33 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Thank you for purchasing a CyberPower product. Please take a few minutes to register your product at www.cpsww.com/registration.

Registration certiﬁes your product's warranty, conﬁrms your ownership in the event of a product loss or theft and entitles you to free technical

support. Register your product now to receive the beneﬁts of CyberPower ownership.

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit.

Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION! To prevent the risk of ﬁre or electric shock, install in a temperature and humidity controlled indoor area free of conductive

contaminants. (Please see speciﬁcations for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. Turn off and unplug the unit before

servicing the batteries. There are no user serviceable parts inside except for the battery.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.

CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not

grounded. If you need to de-energize this equipment, turn oﬀ and unplug the unit.

CAUTION! To avoid electric shock, turn oﬀ the unit and unplug it from the AC power source before installing a computer component.

CAUTION! Not for use in a computer room as deﬁned in the Standard for the Protection of Electronic Computer/Data Processing Equipment,

ANSI/NFPA 75.

CAUTION! To reduce the risk of ﬁre, connect only to a circuit provided with 20 amperes maximum branch circuit over current protection in

accordance with the National Electric Code, ANSI/NFPA 70.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical

applications. use in any circumstance that would aﬀect operation and safety of life support equipment, any medical applications or DO NOT

patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of ﬁre or electric shock, do not use with or near an aquarium. Condensation

from the aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of ﬁre or electric shock, do not use the unit on any transportation

such as airplanes or ships. The eﬀect of shock or vibration caused ing transit and the damp environment can cause the unit to short out. dur

INTRODUCTION

Thank you for selecting a CyberPower Systems UPS product. This UPS is designed to provide unsurpassed power protection, operation and

performance during the lifetime of the product.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS unit (b) User’s manual (c) USB device cable

*PowerPanel® Personal Edition software is available on our website. Please visit www.cpsww.com and go to the Software Section

f a free download. or

AUTOMATIC VOLTAGE REGULATOR

The AVRG750 LCD / AVRG900LCD stabilizes inconsistent utility power to nominal levels that are safe

for equipment. Unstable utility power can be damaging to important data and hardware. With Automatic

Voltage Regulation (AVR), damaging voltage levels are corrected to safe levels. AVR automatically

increases low utility power to a consistent and safe 110/120 volts.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR

EQUIPMENT

1. Ensure that the equipment plugged into the UPS does not e y If the rated capacities of the unit are xceed the UPS unit’s rated capacit .

exceeded, an overload condition may occur and cause the UPS unit to shut down or the circuit breaker to trip.

2. There are many factors that can aﬀect the amount of power that your electronic equipment will require. For optimal system performance

keep the load below 80% of the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, after receiving a new UPS, to

ensure the battery s maximum charge capacity, it is recommended that you charge the battery ’

for at least 8 hours. Your UPS is equipped with an auto-charge feature. When the UPS is

plugged into an AC outlet, the battery will automatically charge whether the UPS is turned on or

turned oﬀ.

2. With the UPS unit turned oﬀ and unplugged, connect your computer, monitor, and any other peripherals

requiring battery backup into the battery power supplied outlets. Plug the other peripheral equipment (eg.

printer, scanner, speakers, etc.) into the full-time surge protection outlets. DO NOT plug a laser printer,

paper shredder, copier, spa heater, vacuum cleaner, sump pump, or other large electrical device into ce

the Battery and Surge Protected Outlets The power demands of these devices will overload and “ ”.

possibly damage the unit.

3. To protect a fax, phone, or modem line, connect a telephone cable from the wall jack outlet to the jack of the IN

UPS. Connect a telephone cable from one of the UPS OUT jacks to the modem port on the computer. The

other UPS OUT jack can be used to protect a telephone or fax machine.

4. ed Plug the UPS into a 2 pole, 3 wire ground receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air

conditioner, refrigerator, copier, etc. The warranty prohibits the use of extension cords, outlet strips, ).

and surge strips in conjunction with the UPS unit.

5. be Press the power switch to turn the unit on. The Power On indicator light will illuminate green and the unit will “ ep” once.

6. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS oﬀ and unplug at

least one piece of equipment from the battery power supplied outlets. Make sure the circuit breaker is depressed and then turn the UPS on.

7. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

8. To store the UPS for an extended period of time, cover it and store with the battery fully charged. While in storage, recharge the battery every

three months to ensure optimal ttery life. ba

9. Ensure the wall outlet and UPS are located near the equipment being attached for proper accessibility.

DESCRIPTION

1. ttery and Surge Protected Outlets Ba

The unit has six battery powered and surge protected outlets to ensure temporary uninterrupted operation of your equipment during a power

failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum cleaner, sump pump, or other large electrical

device into the Battery and Surge Protected Outlets. The power demands of these devices will overload and possibly damage “ ”

the unit.)

2. Full-Time Surge Protection Outlets

The unit has six surge suppression outlets.

3. Power Switch

Used as the master on/oﬀ switch for equipment connected to the battery power supplied outlets.

To turn the UPS ON, press the power button for approximately 2 seconds - you will hear a constant tone (1 second) - and release after a

short beep.

To turn the UPS OFF, press the power button for approximately 2 seconds - you will hear a constant tone (1 second) - and release after two

short beeps.

Alarm setting: The audible alarm can be turned by quickly pressing the POWER button twice. The default setting is for the Alarm Oﬀ or On

On. To turn the Alarm Oﬀ, quickly press the power button twice. You will hear two short beeps when the Alarm is turned Off. To turn the Alarm

back On, quickly press the power button twice. You will hear a single short beep when the Alarm is turned On. *When the Alarm is turned Oﬀ,

there will be no audible notiﬁcation when the UPS reaches a low battery state.

4. Power On Indicator

This LED is illuminated when the utility power is normal and the UPS outlets are providing power, free of surges and spikes.

5. Mode Switch

Press the Mode Switch for approximately 3 seconds enter setup mode to select three functions: Utility High Voltage Range, Utility Low to

Voltage Range, and LCD sleep ON/OFF. When a function is selected, press Mode Switch for 3 seconds to view options. When an option is

selected, wait for 8 seconds for the setting to be conﬁrmed. After the setting has been conﬁrmed the LCD screen will leave setup mode and

go back to status display. If there is no action for 8 seconds during setup, the LCD will also leave setup mode and go back to the status

display.

a. Utility High Voltage Range: Adjust the value of high voltage range.

b. Utility Low Voltage Range: Adjust the value of low voltage range.

c. LCD: L1/L0 (ON/OFF):

* When LCD is set to L1, LCD will be always ON. When LCD is set to L0, LCD will dim if untouched for 1 minut e.

* In battery mode, LCD is always on regardless if the setting is L1 or L0.

6. LCD module display

LCD display shows all the UPS information using icons and messages. For more information please review the Deﬁnitions for Illuminated “

LCD Indicators section. ”

7. USB Port

The USB port allows connection and communication between the USB port on the computer the UPS unit. and

8. Communication Protection Ports

Communication protection ports will protect any standard modem, fax or telephone line. (RJ11) ,

9. Circuit Breaker

Located on the side of the UPS, the circuit breaker provides overload and fault protection.

10. Ground Screw

The ground screw is used for any equipment that needs a chassis ground connection.

11. Outlets Designed for AC Adapters

The UPS unit has four widely-spaced outlets. wer adapters can be plugged into the UPS without overlapping or blocking adjacent AC po

outlets.

REPLACING THE BATTERY

Replacement of batteries located in an OPERATOR ACCESS AREA.

1. When replacing batteries, replace with the same number of the following battery: CyberPower / RB1270B for AVRG750LCD CyberPower ;

/ RB1290A for AVRG900LCD.

2. CAUTION! Risk of Energy Hazard, 12V, maximum 9 Ampere- battery. Before replacing batteries, remove conductive jewelry such as hour

chains, wrist watches, and rings. High energy through conductive materials could cause severe burns.

3. Do not dispose of batteries in a ﬁre. The batteries may explode. CAUTION!

4. Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It may be toxic. CAUTION!

CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING

TO LOCAL REGULATIONS.

TO REPLACE THE BATTERY

1. Turn oﬀ and unplug all connected equipment.

2. Unplug it from the AC power source.

3. Turn the UPS upside down.

4. Remove the 1 retaining screw.

5. Slide the battery compartment cover completely oﬀ of the unit.

6. Remove the battery from the compartment.

7. Disconnect the battery wires from the battery.

8. Install the replacement battery by connecting the red wire and black wire to the positive (+) and negative (-) terminal of the battery.

9. Put the battery back into the compartment.

10. Slide back the battery compartment cover and tighten the retaining screw.

11. Charge the unit for 8 hours to fully charge the battery.

REMINDER: HAZARDOUS WASTEBatteries are consider ed and must be disposed of properly. Most retailers that sell lead-acid batteries

collects used batteries for recycling, as required by local regulations.

Problem

Possible Cause

Solution

Full-time surge protection outlets

stop providing power to

equipment. Circuit breaker

button is projecting from the side

of the unit.

Circuit breaker has tripped due been

to an overload.

Turn the UPS oﬀ and unplug at least one piece of

equipment. Wait 10 seconds, reset the circuit breaker by

pressing the button, and then turn the UPS on.

The UPS does not perform

expected runtime.

Battery not fully charged.

Recharge the battery by leaving the UPS plugged in.

Battery is worn out.

Contact CyberPower Systems about replacement bat ries te

at tech@cpsww.com.

The UPS will not turn on.

The on/oﬀ switch is designed to

prevent damage from rapidly turning

it oﬀ and on.

Turn the UPS oﬀ. Wait 10 seconds and then turn the UPS

on.

The unit is not connected to an AC

outlet.

The unit must be connected to a V 60Hz outle 120 t.

The battery is worn out.

Contact CyberPower Systems about replacement batteries

at tech@cpsww.com.

Mechanical problem.

Contact CyberPower Systems at . tech@cpsww.com

The frequency is outside of the

operating range of -63Hz. 57

Turn the UPS oﬀ. Make sure the frequency range is within

57-63Hz. Or you can turn the UPS on in battery mode.

PowerPanel® Personal Edition is

inactive (all icons are gray).

The USB cable is not connected.

Connect the USB cable to the UPS unit and an open USB

port on the back of the computer.

The USB cable is connected to a

bad USB port.

Check for a diﬀerent USB port and plug the cable in.

The unit is not providing battery

power.

Shutdown your computer and turn the UPS oﬀ. Wait 10

seconds and turn the UPS back on. This should reset the

unit.

Additional troubleshooting information can be found at Support “ ” at www.CPSww.com

AVRG750LCD / AVRG900LCD

User Manual ’s

K01-0000445- 00

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

TROUBLESHOOTING

IMPORTANT SAFETY INSTRUCTIONS

PRODUCT REGISTRATION

AVRG750L / AVRG900LCD CD

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	AVRG750LCD
Bredde:	310 mm
Dybde:	88.9 mm
Højde:	178 mm
Vægt:	5620 g
Produktfarve:	Sort
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Kompakt
Opbevaringstemperatur (T-T):	-15 - 45 °C
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Antal USB 2.0-porte:	1
Driftstemperatur (T-T):	0 - 40 °C
Udgangseffekt:	450 W
Kabellængde:	1.5 m
Antal understøttede batterier:	1
Bæredygtighedscertifikater:	RoHS, ENERGY STAR
Driftshøjde:	0 - 2000 m
Ikke-drift højde:	0 - 15000 m
Indgangsfrekvens:	60 Hz
Strømbeskyttelsesfunktioner:	Overbelastning
Strømstik:	NEMA 5-15P
Sikkerhed:	UL1778 4th, cUL 107.3-05, FCC/DoC Class B
Modem-porte (RJ-11):	3
AC udgange, antal:	12 AC stikkontakt(er)
AC stikkontakt typer:	NEMA 5–15R
Overspænding energivurdering:	1030 J
Indgående driftsspænding (maks.):	148 V
Output strømkapacitet (VA):	0.75 kVA
Indgående driftsspænding (min.):	90 V
Udgangs driftsspænding (min.):	120 V
Udgangs driftsspænding (maks.):	120 V
UPS topologi:	Interaktivt indgangsstik
Beskyttelse ved overspænding:	Ja
Typisk backup tid ved halv styrke:	7.6 min.
Typisk backup tid ved fuld styrke:	2.5 min.
Automatisk spændingsregulering (AVR):	Ja
EMI/RFI støjfiltrering:	Ja