CyberPower CP600LCD Manual

CyberPower Uafbrydelig strømforsyning (UPS) CP600LCD

Læs nedenfor 📖 manual på dansk for CyberPower CP600LCD (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne guide var nyttig for 26 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

CP825LCD | CP600LCD

User’s Manual

PRODUCT REGISTRATION

IMPORTANT SAFETY INSTRUCTIONS

INSTALLING YOUR UPS SYSTEM

BASIC OPERATION

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

BASIC OPERATION CONT.

DEFINITIONS FOR LED INDICATORS & AUDIBLE ALARMS

Thank you for selecting this CyberPower UPS product. This UPS is designed to provide unsurpassed power

protection, operation and performance during the lifetime of the product. Please take a few minutes to register

your product by visiting: CyberPowerSystems.com/registration. Registration certiﬁes your product’s warranty,

conﬁrms your ownership in the event of a product loss or theft and entitles you to free technical support.

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during

installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or

operate your UPS.

CAUTION! To prevent the risk of ﬁre or electric shock, install in a temperature and humidity controlled

indoor area free of conductive contaminants. (Please see speciﬁcations for acceptable temperature and

humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery.

Turn o and unplug the unit before servicing the batteries. There are no user-serviceable parts inside

except for the battery.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input

power is disconnected.

CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection.

Do not plug into an outlet that is not grounded. If you need to de-energize this equipment, turn o and

unplug the unit.

CAUTION! To avoid electric shock, turn o the unit and unplug it from the AC power source before

installing components.

CAUTION! Not for use in a computer room as deﬁned in the Standard for the Protection of Electronic

Computer/Data Processing Equipment, ANSI/NFPA 75.

CAUTION! To reduce the risk of ﬁre, connect only to a circuit provided with 20 amperes maximum branch

circuit over current protection in accordance with the National Electric Code, ANSI/NFPA 70.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! Under no circumstances should this unit be

used for medical applications involving life support equipment and/ or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of ﬁre or electric shock, do not use with or

near an aquarium. Condensation from the aquarium can come in contact with metal electrical contacts

and cause equipment to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of ﬁre or electric shock, do not

use the unit on any transportation such as airplanes or ships. The eect of shock or vibration caused

during transit and the damp environment can cause the unit to short out.

UNPACKING

Inspect the UPS upon receipt, the box should contain the following: UPS unit, User manual, USB

A+B type cable and *PowerPanel® Personal Edition software is available as a free download at:

CyberPowerSystems.com/products/software.

OVERVIEW

The CP825LCD/CP600LCD provides complete power protection from utility power that is not always

consistent. The CP825LCD/CP600LCD features 1030 Joules of surge protection. The unit provides

long lasting battery backup during power outages with maintenance free batteries. The CP825LCD/

CP600LCD ensures consistent power to your computer system and includes software that will

automatically save your open ﬁles and shutdown your computer system during a utility power loss.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the UPS does not exceed the UPS unit’s rated capacity

(825VA/450W for CP825LCD, 600A/340W for CP600LCD). If the rated capacities of the unit are

exceeded, an overload condition may occur and cause the UPS unit to shut down or the circuit

breaker to trip.

2. There are many factors that can aect the amount of power that your electronic equipment will

require. For optimal system performance keep the load below 80% of the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However,

after receiving a new UPS, to ensure the battery’s maximum

charge capacity, it is recommended that you charge the battery

for at least 8 hours. Your UPS is equipped with an auto-charge

feature. When the UPS is plugged into an AC outlet, the battery

will automatically charge whether the UPS is turned on or turned

o. Note: This UPS is designed with a safety feature to keep the

system from being turned on during shipment. The ﬁrst time you

turn the UPS on, you will need to have it connected to AC power

or it will not power up.

2. With the UPS unit turned o and unplugged, connect your computer, monitor, and any other

peripherals requiring battery backup into the battery power supplied outlets. Plug the other peripheral

equipment (eg. printer, scanner, speakers, etc.) into the full-time surge protection outlets. DO NOT

plug a laser printer, paper shredder, copier, space heater, vacuum cleaner, sump pump, or other large

electrical device into the “Battery and Surge Protected Outlets”. The power demands of these devices

will overload and possibly damage the unit.

3. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the

wall branch outlet is protected by a fuse or circuit breaker and does not service

equipment with large electrical demands (e.g. air conditioner, refrigerator, copier,

etc.). The warranty prohibits the use of extension cords, outlet strips, and surge strips

in conjunction with the UPS unit.

4. Press the power switch to turn the unit on. The Power On indicator light will illuminate

green and the unit will “beep” once.

5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct

this, turn the UPS o and unplug at least one piece of equipment from the battery power supplied

outlets. Make sure the circuit breaker is depressed and then turn the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store the UPS for an extended period of time, cover it and store with the battery fully charged.

While in storage, recharge the battery every three months to ensure optimal battery life.

8. Ensure the wall outlet and UPS are located near the equipment being attached for proper accessibility.

1. Power Switch: Used as the master on/o switch for equipment connected to the battery power

supplied outlets. To turn the UPS ON, press the power button for approximately 2 seconds - you will

hear a constant tone (1 second) - and release after a short beep.

Alarm setting: The audible alarm can be turned O or On by double click the POWER button. The

default setting is for the Alarm On. To turn the Alarm O, double click the button. You will hear two

short beeps when the Alarm is turned o. To turn the Alarm back On, double click the button. You will

hear a single short beep when the Alarm is turned on. *When the Alarm is turned O, there will be no

audible notiﬁcation when the UPS reaches a low battery state.

2. Power On Indicator: This LED is illuminated when the utility power is normal

and the UPS outlets are providing power, free of surges and spikes.

3. Mode Switch: Press the Mode Switch for approximately 3 seconds to enter

setup mode to view options: Utility High/low Voltage range, sensitivity

setup, LCD sleep ON/OFF, battery test, buzzer ON/OFF, and low battery

alarm. When an option is selected, wait for 8 seconds for the setting to

be conﬁrmed. After the setting has been conﬁrmed the LCD screen will

leave setup mode and go back to status display. If there is no action for 8

seconds during setup, the LCD will also leave setup mode and go back to

the status display.

4. Fault Indicator: This LED is illuminated if there is a problem with the UPS

5. LCD module display: LCD display shows all the UPS information using

icons and messages. For more information please review the “Deﬁnitions

for Illuminated LCD Indicators” section.

6. Battery and Surge Protected Outlets: The unit has four battery powered

and surge protected outlets to ensure temporary uninterrupted operation

of your equipment during a power failure. (DO NOT plug a laser printer,

paper shredder, copier, space heater, vacuum cleaner, sump pump, or other

large electrical device into the “Battery and Surge Protected Outlets.” The

power demands of these devices will overload and possibly damage the

unit.)

INPUT voltage meter: This meter measures the AC voltage that the UPS system is receiving from the

utility wall outlet. The UPS is designed to continuously supply connected equipment with stable output

voltage. In the event of a complete power loss, severe brownout, or over-voltage, the UPS relies on its

internal battery to supply consistent 110/120 output voltage. The INPUT voltage meter can be used as a

diagnostic tool to identify poor-quality input power.

OUTPUT voltage meter: This meter measures, in real time, the AC voltage that the UPS system is

providing to the computer during normal AC/Utility Power mode, and battery backup mode.

ESTIMATED RUNTIME: This displays the run time estimate of the UPS with the

current battery capacity and load.

NORMAL icon: This icon appears when the UPS is working under normal

conditions.

BATTERY icon: During a severe brownout or blackout, this icon appears and

an alarm sounds (two short beeps followed by a pause) to indicate the UPS

is operating from its internal batteries. During a prolonged brownout or

blackout, the alarm will sound continuously to indicate the UPS’s batteries

are nearly out of power. You should save ﬁles and turn o your equipment

immediately or allow the software to shut the system down.

OVER LOAD icon: This icon appears and an alarm sounds to indicate the

battery-supplied outlets are overloaded. To clear the overload, unplug some

of your equipment from the battery-supplied outlets until the icon turns o

and the alarm stops.

BATT. CAPACITY meter: This meter displays the approximate charge level of the UPS’s internal battery in

20% increments. During a blackout or severe brownout, the UPS switches to battery power (the BATTERY

icon appears) and the battery charge level decreases.

LOAD CAPACITY meter: This meter displays the approximate output load level of the UPS battery outlets

in 20% increments.

SENSITIVITY meter: This meter displays the sensitivity level of the UPS. It is to control the sensitivity of

the UPS to switch to Battery Mode by selecting UPS shutdown voltage range. When the sensitivity is

increased, the UPS will switch to Battery Mode with less input power variation.

FAULT: The following number appears if there is a problem with the UPS. Press the POWER button to turn

the UPS o.

E22: Battery Mode or AC/Utility Power Mode Overload fault (Unplug at least one piece of equipment

from battery outlets and turn the UPS on again.)

E21: Battery Output Short fault (Unplug at least one piece of equipment from battery outlets and turn the

UPS on again.)

E01: Charger Fault (Contact CyberPower Systems for support)

E24: Internal Fault (Contact CyberPower Systems for support)

CP825LCD | CP600LCD

POWER FAULT ALARM

CONDITION

On O O Normal

On O

Beep twice

every 30

seconds

Utility Failure: The UPS is providing power to battery

power-supplied outlets from its battery.

On O

Rapid

beeping

every

½ second

Utility Failure: The UPS is providing battery power.

Rapid beeping indicates the unit will run out of power

soon.

On/O

Flash once

every 5

seconds

Constant tone

Battery Mode or AC/Utility Power Mode Overload Fault:

Occurs when connected equipment exceeds the rating of

battery outlets of the unit. Please unplug at least one piece

of equipment from battery outlets.

O

Flash twice

every 5

seconds

Constant tone

Battery Output Short Fault: Please unplug at least one

piece of equipment from battery outlets and turn on the

UPS again. If the fault still exists, please contact Cyber-

Power Systems for support.

Flash 3

times every

5 seconds

Constant tone Charger Fault: Contact CyberPower for support.

7. Full-Time Surge Protection Outlets: The unit has four surge suppression outlets. To turn the UPS OFF,

press the power button for approximately 2 seconds - you will hear a constant tone (1 second) - and

release after two short beeps.

8. USB Port: The USB port allows connection and communication between the USB port on the computer

and the UPS unit.

9. Serial Port: Serial Port allow for bi-directional communication among the UPS and the computer. The

UPS can control the computer’s shutdown in case of an emergency, and at the same time, the computer

can monitor the UPS and alter its various programmable parameters.

10. Circuit Breaker & Reset: Located on the side of the UPS, the circuit breaker provides overload and fault

protection.

11. Ground Screw: The ground screw is used for any equipment that needs a chassis ground connection.

12. Outlets Designed for AC Adapters: The UPS unit has four widely-spaced outlets. AC power adapters

can be plugged into the UPS without overlapping or blocking adjacent outlets.

REPLACING THE BATTERY

Replacement of batteries located in an OPERATOR ACCESS AREA.

1. When replacing batteries, replace with the same number of the following battery:

CyberPower / RB1290 for CP825LCD; CyberPower / RB1270B for CP600LCD

2. CAUTION! Risk of Energy Hazard, 12V, maximum 9 Ampere-hour battery. Before replacing batteries,

remove conductive jewelry such as chains, wrist watches, and rings. High energy through conductive

materials could cause severe burns.

3. CAUTION! Do not dispose of batteries in a ﬁre. The batteries may explode.

4. CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It may be

toxic.

5. CAUTION: A battery can present a risk of electrical shock and high short circuit current. The following

precautions should be observed when working on batteries:

a, Remove watches rings, or other metal objects

b. Use tools with insulated handles.

CAUTION: risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries

according to local regulations.

*In line mode, the AC input voltage may not stable all the time. To prevent the connected equipment

from damage caused by the unexpected voltage ﬂuctuations, please adjust the sensitivity of the unit by

visiting: www.cyberpowersystems.com and download the LCD setup guide.*

TO REPLACE THE BATTERY

1. Turn o and unplug all connected equipment.

2. Unplug it from the AC power source.

3. Turn the UPS upside down.

4. Remove the 1 retaining screw.

5. Slide the battery compartment cover completely o of the unit.

6. Remove the battery from the compartment.

7. Disconnect the battery cables from the battery.

8. Install the replacement battery by connecting the red wire and black wire

to the positive (+) and negative (-) terminal of the battery.

9. Put the battery back into the compartment.

10. Slide back the battery compartment cover and tighten the retaining screw.

11. Charge the unit for 8 hours to fully charge the battery.

REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly. Most

retailers that sell lead-acid batteries collects used batteries for recycling, as required by local regulations.

The LCD display indicates a

variety of UPS operational

conditions. All descriptions

apply when the UPS is

plugged into an AC outlet

and turned on or when the

UPS is on battery.

RUN_TIMEOUTPUTINPUT

Min

LOAD BATT. CAP.

100

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	CP600LCD
Vægt:	6350 g
Responstid:	4 ms
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Ethernet LAN-porte (RJ-45):	1
Antal USB 2.0-porte:	1
Driftstemperatur (T-T):	32 - 95 °F
Dimensioner (BxDxH):	279.4 x 165.1 x 89 mm
Udgangseffekt:	340 W
Certificering:	UL1778, cUL 107.1, FCC DOC Class B
Opladningstid for batteri:	8 t
Indgangsfrekvens:	60 Hz
Lydalarmer:	Ja
Input forbindertype:	NEMA 5-15P
Vægt (efter britisk standard):	14 Pund
Output-forbindere:	NEMA 5-15R
Dimensioner (BxDxH) (efter britisk standard):	11 x 3.5 x 6.5 "
Modem-porte (RJ-11):	1
Overspænding energivurdering:	1030 J
Output strømkapacitet (VA):	0.6 kVA
UPS topologi:	Standby (offline)
Strøm (maks.):	- A
Typisk backup tid ved halv styrke:	9 min.
Typisk backup tid ved fuld styrke:	2 min.
Udskiftningsbatteri:	BB - SH1228W