CyberPower EC550G Manual

CyberPower Uafbrydelig strømforsyning (UPS) EC550G

Læs nedenfor 📖 manual på dansk for CyberPower EC550G (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne guide var nyttig for 61 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

EC350G / EC550G / EC750G

EC650LCD / EC850LCD

User’s Manual

K01-0000277-00

Thank you for purchasing a CyberPower product. Please take a few minutes to register your product at www.cpsww.com/registration.

Registration certifies your product's warranty, confirms your ownership in the event of a product loss or theft and entitles you to free technical

support.

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit.

Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive

contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.

CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not

grounded. If you need to de-energize this equipment, turn off and unplug the unit.

CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before installing a computer component.

CAUTION! Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment,

ANSI/NFPA 75.

CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit over current protection in

accordance with the National Electric Code, ANSI/NFPA 70.

CAUTION! Risk of explosion if battery is replaced by an incorrect type. Batteries shall be installed by service personnel, and the replacement of

batteries with a suitable recommended type. Dispose of used batteries according to the instructions.

CAUTION! Do not dispose of batteries in a fire. The batteries may explode.

CAUTION! Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may be toxic.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical

applications. use in any circumstance that would affect operation and safety of life support equipment, any medical applications or DO NOT

patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium. Condensation

from the aquarium can cause the unit to short out.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS unit (b) User’s manual (c) USB device cable

*PowerPanel® Personal Edition software is available on our website. Please visit www.cpsww.com and go to the Software Section for

free download.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the UPS does not exceed the UPS unit’s rated capacity (350VA/255W for EC350G, 550VA/330W for

EC550G, 750VA/450W for EC750G, 650VA/390W for EC650LCD, and 850VA/510W for EC850LCD). If the rated capacities of the unit are

exceeded, an overload condition may occur and cause the UPS unit to shut down or the circuit breaker to trip.

2. There are many factors that can affect the amount of power that your electronic equipment will require. For optimal system performance

keep the load below 80% of the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, after receiving a new UPS, to

ensure the battery’s maximum charge capacity, it is recommended that you charge the battery

for at least 8 hours. Your UPS is equipped with an auto-charge feature. When the UPS is

plugged into an AC outlet, the battery will automatically charge when it’s turned on or turned off.

2. With the UPS unit turned off and unplugged, connect your computer, monitor, and any other

peripherals requiring battery backup from the SURGE/BATTERY outlets. Plug the other peripheral equipment (e.g. printer, scanner,

speakers, etc.) into the full-time surge protection outlets. DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum

cleaner, sump pump, or other large electrical device into the “Battery and Surge Protected Outlets”. The power demands of these

devices will overload and possibly damage the unit.

3. To protect a fax, phone, or modem line, connect a telephone cable from the wall jack outlet to the IN jack of the UPS.

Connect a telephone cable from the UPS OUT jack to protect a modem port on the computer, a telephone, or fax machine.

4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air

conditioner, refrigerator, copier, etc.). The warranty prohibits the use of extension cords, outlet strips,

and surge strips in conjunction with the UPS unit.

5. Press the power switch to turn the unit on. The Power On indicator light will illuminate green and the unit will “beep” twice.

6. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at

least one piece of equipment from the battery power supplied outlets. Make sure the circuit breaker is depressed and then turn the UPS on.

7. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

8. To store the UPS for an extended period of time, cover it and store with the battery fully charged. While in storage, recharge the battery

every three months to ensure optimal battery life.

9. Ensure the wall outlet and UPS are located near the equipment being attached for proper accessibility.

DESCRIPTION

1. Battery and Surge Protected Outlets

The unit has battery powered/surge suppression outlets to ensure temporary uninterrupted operation of your equipment during a power

failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum cleaner, sump pump, or other large electrical

device into the “Battery and Surge Protected Outlets.” The power demands of these devices will overload and possibly damage

the unit.)

2. Full-Time Surge Protection Outlets / ECO Controlled Outlets

The unit has surge suppression outlets to provide surge and line noise protection. Three of the surge-only outlets are also ECO controlled

outlets.

3. Power Switch

To turn the UPS , press the power button for approximately 2 seconds - you will hear a constant tone (1 second) - and release after a ON

short beep.

To turn the UPS OFF, press the power button for approximately 2 seconds - you will hear a constant tone (1 second) - and release after two

short beeps.

Alarm setting: The audible alarm can be turned by quickly pressing the POWER button twice. The default setting is for the Alarm Off or On

On. To turn the Alarm Off, quickly press the power button twice. You will hear two short beeps when the Alarm is turned Off. To turn the

Alarm back On, quickly press the power button twice. You will hear a single short beep when the Alarm is turned On. *When the Alarm is

turned Off, there will be no audible notification when the UPS reaches a low battery state.

4. Power On Indicator (green)

This LED is illuminated when the utility power is normal and the UPS outlets are providing power, free of surges and spikes.

5. Mode Switch (EC650LCD and EC850LCD only)

Press the Mode Switch for approximately 3 seconds to enter setup mode to select four functions: Utility High Voltage Range, Utility Low

Voltage Range, ECO ON/OFF, and LCD sleep ON/OFF. When a function is selected, press Mode Switch for 3 seconds to view options.

When an option is selected, wait for 8 seconds for the setting to be confirmed. After the setting has been confirmed the LCD screen will

leave setup mode and go back to status display. If there is no action for 8 seconds during setup, the LCD will also leave setup mode and go

back to the status display.

a. Utility High Voltage Range: Adjust the value of high voltage range.

b. Utility Low Voltage Range: Adjust the value of low voltage range.

c. ECO: Eon/EoF (ON/OFF): Turn on or turn off ECO function. For more information, refer to section. ECO Function Setup

d. LCD: L1/L0 (ON/OFF):

* When LCD is set to L1, LCD will be always ON. When LCD is set to L0, LCD will dim if untouched for 1 minute.

* In battery mode, LCD is always on regardless if the setting is L1 or L0.

ECO Button (EC350G, EC550G, and EC750G only)

Press ECO button for 3 seconds to turn on or turn off ECO function in line mode.

6. ECO Indicator

ECO Indicator shows the condition of ECO function. For more information, refer to section. ECO Function Setup

7. Communication Protection Ports

Communication protection ports will protect any standard modem, fax, or telephone line. (RJ11)

8. Circuit Breaker

Located on the side of the UPS, the circuit breaker serves to provide overload and fault protection.

9. USB Port to PC

The USB port allows connection and communication between the USB port on the computer and the UPS unit. The UPS communicates its

status to the PowerPanel® Personal Edition software. The USB port is also used for operating the UPS in ECO mode. For more information,

refer to section. ECO Function Setup

10. Outlets Designed for AC Adapters

The UPS unit has 4 widely-spaced outlets so AC power adapters can be plugged into the UPS without overlapping or blocking adjacent

outlets.

ECO FUNCTION SETUP

ECO Function

When the ECO function is active the UPS can detect whether the PC that is connected to the USB port is turned on or off. If the PC is turned

off, the UPS will turn off the ECO controlled outlets and cut power to the devices connected to them in order to save power. Generally, these

are peripherals that are not used when the PC is not turned on.

ECO Controlled Outlets

Three of the surge-only outlets are also ECO controlled outlets. When the PC that is connected to the USB port is turned off, the UPS will

turn off the ECO controlled outlets to save energy.

ECO Setup

1. The factory default setting is OFF. ECO mode can only be enabled/disabled and will only be active when the UPS is receiving utility

power and not in battery mode.

2. For the EC650/850LCD, press the Mode switch for approximately 3 seconds to enter setup mode and select the ECO function. When

the ECO function is selected, press the Mode switch for 3 seconds to turn the function ON or OFF. Once ON or OFF is selected, wait 8

seconds for the setting to be confirmed and the LCD screen will return to status mode. For the EC350/550/750G, press the ECO button

for 3 seconds to turn ON or OFF the ECO function.

3. When the ECO function is OFF, utility power from the ECO outlets will always be on. When the ECO function is ON, utility power from

the ECO outlets will turn off if the PC connected to the UPS via the USB port is turned off or if there is no PC is connected to the UPS via

USB.

ECO Indicator

The LED will be blinking when the ECO function is turned ON but the PC is either off or not connected. The LED will be solid if the ECO

function is turned on and the connected PC is on. The LED is off when the ECO function is disabled. See below table for more information.

ECO Indicator ECO Function ECO Outlet Status Condition

Solid (green) ON With Utility Power When PC is ON and USB port on the UPS is connected, Peripherals

will receive power to operate.

Blinking ON Without Utility Power When PC is OFF or the USB port on the UPS is not connected, power

to the Peripherals will be turned off.

OFF OFF Always with Utility

Power

When PC is ON/OFF, Peripherals is always ON.

DEFINITIONS FOR ILLUMINATED LED INDICATORS

Power ON

Alarm

CONDITION

On Off Normal

On Beep twice

every 30 seconds

Utility Failure- The UPS is providing power to battery power-supplied

outlets from its battery.

On Rapid Beeping

every 1/2 second

Utility Failure- The UPS is providing battery power. Rapid beeping

indicates the unit will run out of power shortly.

Off Constant tone

Battery Overload - Occurs when connected equipment exceeds the

listed capacity of the UPS. Turn the UPS off, unplug at least one

piece of equipment from battery outlets, wait 10 seconds, reset the

circuit breaker and turn the unit on.

INPUT voltage meter: This meter measures the AC voltage that the UPS system is receiving from the

utility wall outlet. The UPS is designed to continuously supply connected equipment with stable output

voltage. In the event of a complete power loss, severe brownout, or over-voltage, the UPS relies on its

internal battery to supply consistent 110/120 output voltage. The INPUT voltage meter can be used as

a diagnostic tool to identify poor-quality input power.

OUTPUT voltage meter: This meter measures, in real time, the AC voltage that the UPS system is

providing to the computer during normal AC/Utility Power mode, and battery backup mode.

ESTIMATE RUN TIME: This displays the run time estimate of the UPS with the current battery

capacity and load.

NORMAL icon: This icon appears when the UPS is working under normal conditions.

BATTERY icon: During a severe brownout or blackout, this icon appears and an alarm sounds (two short beeps followed by a pause) to indicate

the UPS is operating from its internal battery. The alarm will continue to sound during a prolonged brownout or blackout. The BATT.CAPACITY

meter will show one 20% capacity segment remaining to indicate the UPS's battery is nearly out of power. You should save files and turn off your

equipment immediately.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY WARNINGS

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

The LCD display indicates a variety

of UPS operational conditions. All

descriptions apply when the UPS is

plugged into an AC outlet and turned

on or when the UPS is on battery.

PRODUCT REGISTRATION

EC650LCD (8 outlets)

EC850LCD

(12

outlets)

EC350G / EC550G (8 outlets)

EC750G

(12 outlets)

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	EC550G
Bredde:	269.24 mm
Dybde:	149.86 mm
Højde:	78.74 mm
Vægt:	2721.55 g
Produktfarve:	Sort
Batterispænding:	12 V
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Kompakt
Opbevaringstemperatur (T-T):	-15 - 45 °C
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 95 %
Antal USB 2.0-porte:	1
Driftstemperatur (T-T):	0 - 40 °C
Udgangseffekt:	330 W
Certificering:	UL1778, cUL 107.3, FCC
LED-indikatorer:	Ja
Kabellængde:	1.5 m
Opladningstid for batteri:	8 t
Bæredygtighedscertifikater:	RoHS, ENERGY STAR
Medfølgende software:	PowerPanel
Driftshøjde:	0 - 3000 m
Ikke-drift højde:	0 - 15000 m
Indgangsfrekvens:	47/63 Hz
Lydalarmer:	Ja
Strømbeskyttelsesfunktioner:	Overbelastning
Strømstik:	NEMA 5-15P
Nominel udgangsspænding:	120 V
Modem-porte (RJ-11):	2
AC udgange, antal:	8 AC stikkontakt(er)
AC stikkontakt typer:	NEMA 5–15R
Overspænding energivurdering:	526 J
Indgående driftsspænding (maks.):	140 V
Output strømkapacitet (VA):	0.55 kVA
Indgående driftsspænding (min.):	96 V
Udgangs driftsspænding (min.):	- V
Udgangs driftsspænding (maks.):	- V
UPS topologi:	Standby (offline)
Beskyttelsesfunktioner mod strømstød:	Modem, Telephone
Beskyttelse ved overspænding:	Ja
Bølgeform:	Sine
Typisk backup tid ved halv styrke:	7.35 min.
Typisk backup tid ved fuld styrke:	2.4 min.
EMI/RFI støjfiltrering:	Ja