CyberPower PP1100SW Manual

CyberPower Uafbrydelig strømforsyning (UPS) PP1100SW

Læs nedenfor 📖 manual på dansk for CyberPower PP1100SW (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne guide var nyttig for 27 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Professional Tower UPS

PP800/PP1100/PP1500T

User Manual K01-P1K50I0

SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit.

Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

This equipment can be operated by any individuals with no previous training.

The socket-outlet shall be installed near the equipment and easily accessible.

During the installation of this equipment it should be assured that the sum of the leakage currents of the UPS and the connected loads does not

exceed 3.5mA.

Attention, hazardous through electric shock. Also with disconnection of this unit from the mains, hazardous voltage still may be accessible

through supply from battery. The battery supply should be therefore disconnected in the plus and minus pole at the quick connectors of the

battery when maintenance or service work inside the UPS is necessary.

Do not dispose of batteries in a fire, the battery may explode.

Do not open or mutilate the battery or batteries, released electrolyte is harmful to the skin and eyes.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

UPS Unit¯1; PowerPanel Plus Software Disk¯1; Serial Interface Cable (DB-9)¯1; USB Device Cable¯1;Telephone Cable¯1; User

Manual¯1; PowerPanel Plus Software User Manual¯1.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Insure that the equipment plugged into the battery power-supplied outlets does not exceed the UPS unit’s rated capacity (800VA/550W for

PP800, 1100VA/700W for PP1100, 1500VA/1000W for PP1500T). If rated unit capacities are exceeded, an overload condition may occur

and cause the UPS unit to shut down or the circuit breaker to trip.

2. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert Watts (W) or Amps (A) into VA by doing

the calculations below. Note: The below equation only calculates the maximum amount of VA that the equipment can use, not what is

typically used by the equipment at any one time. Users should expect usage requirements to be approximately 60% of below value.

TO ESTIMATE POWER REQUIREMENTS

1. Watts (W) x 2.0 = VA or

Amps (A) x 120 =

2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual requirements. There are many factors that can

affect the amount of power that your computer system will require. The total load that you will be placing on the battery-powered outlets

should not exceed 80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

1. Connect the equipment to your UPS outlets. Items such as copiers, laser printers, vacuums, space

heaters, paper shredders, or other large electrical devices should not be connected to the UPS.

Please assure that the total loads of your equipments must be less than the maximum total power

load of your UPS.

2. Connect your UPS power cord into a two-pole, three-wire grounding receptacle only. Please avoid

using extension cords and adapter plugs. (To maintain optimal battery charge, leave the UPS

plugged in at all times.)

3. Press the UPS power button to turn it on. The “Power On” indicator will be illuminated in “Green”.

4. Install your optional software and accessories. To use the software, simply connect the enclosed

serial interface cable to the serial port on the UPS and an open serial port on the computer.

BASIC OPERATION

FRONT PANEL DESCRIPTION

 Power Switch

Press the ON/OFF button to turn the UPS on or off.

 Power On Indicator

This LED is illuminated when the utility condition is normal and the UPS outlets are

providing “clean power”, free of surges and spikes.

 Using Battery Indicator

This illuminates during utility failure, indicating that the battery is supplying power to the battery-power supplied outlets.

 Boost Indicator

This LED indicates that the UPS is operating in automatic voltage regulation mode. When this indicator is flashing/

illuminated continuously, it indicates that the UPS is compensating MAX.14%/ 30% for a low utility voltage.

 Buck Indicator

This LED indicates that the UPS is operating in automatic voltage regulation mode. When this indicator is illuminated

continuously, it indicates that the UPS is compensating MAX.12% for a high utility voltage.

REAR PANEL DESCRIPTION

 Battery Backup and Surge Protection Outlets

The UPS provides 4 battery powered and surge protected outlets for connected equipment to insure temporary

uninterrupted operation during a power failure and against surges and spikes.

 Surge Protection Outlets

The UPS provides 3 surge protected only outlets for connected equipments against surges and spikes.

 Serial/USB Port to PC

This port allows connection and communication from the DB-9 serial or USB port on the computer to the UPS unit. The

UPS communicates its status to the PowerPanel Plus™ software. This interface is also compatible with the UPS service

provided by Windows 98, Windows ME, Windows NT, Windows 2000, Windows XP, Windows Server 2003 and Mac

OS 10X.

NOTE: Only one of these two ports can be used as communication and control of the UPS unit at one time.

 Ethernet (RJ-45) Network Protection Ports

These ports are the protection for your computer network device.

BATTERY REPLACEMENT AND STORAGE

Contact your dealer or call the number in this manual for information on battery replacement.

Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery. Service the battery under the supervision of

personnel knowledgeable of batteries and their precautions. Keep unauthorized personnel away from batteries.

CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.

CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in a fire, as it may explode. Follow all local

ordinances regarding proper disposal of batteries.

CAUTION! Do not open or mutilate the batteries. Release electrolyte is harmful to the skin and eyes and may be toxic.

CAUTION! A battery can present a high risk of short circuit current and electric shock. Take the following precautions before replacing the

battery:

1. Remove all watches, rings or other metal objects.

2. Only use tools with insulated handles.

3. DO NOT lay tools or other metal parts on top of battery or any battery terminals.

4. Wear rubber gloves and boots.

5. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source of ground. CONTACT WITH A GROUNDED

BATTERY CAN RESULT IN ELECTRICAL SHOCK! The likelihood of such shock will be reduced if such grounds are removed during

installation and maintenance (applicable to a UPS and a remote battery supply not having a grounded circuit).

STORAGE:

First turn off your UPS and disconnect its power cord from the wall outlet. Disconnect all cables connected to the UPS to avoid battery drain. To

store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to insure

battery life. If the battery remains uncharged for an extended period of time, it may suffer permanent loss of capacity.

TROUBLE SHOOTING

Problem Possible Cause Solution

Batteries are not fully charged.

Recharge the battery by leaving the UPS plugged in.

The UPS does not perform

expected runtime.

Battery is slightly worn out.

Contact CyberPower Systems at tech@cyberpowersystems.com.

The on/off switch is designed to

prevent damage by rapidly

turning it off and on.

Turn the UPS off.

Wait 10 seconds and then turn the UPS on.

The unit is not connected to an

AC outlet.

The unit must be connected to a 110/120v 60Hz outlet.

The battery is worn out.

Contact CyberPower Systems at tech@cyberpowersystems.com.

The UPS will not turn on.

Mechanical problem.

Contact CyberPower Systems at tech@cyberpowersystems.com.

Circuit breaker is tripped due to

overload

Turn the UPS off and unplug at least one piece of equipment. Wait 10

seconds, reset the circuit breaker and then turn the UPS on.

Batteries are discharged

Allow the unit to recharge for at least 4 hours.

Outlets do not provide

power to equipment

Unit has been damaged by a

surge or spike.

Contact CyberPower Systems at tech@cyberpowersystems.com.

The serial cable is not

connected.

Connect the serial cable to the UPS unit and an open serial port on the back

of the computer. You must use the cable that came with the unit.

The serial cable is connected to

the wrong port.

Check the back of the computer for an additional serial port. Move the

cable to this port.

The unit is not providing battery

power.

Shutdown your computer and turn the UPS off. Wait 10 seconds and turn the

UPS back on. This should reset the unit.

PowerPanel Plus™ is

inactive (all icons are gray).

The serial cable is not the cable

that was provided with the unit.

You must use the cable that was included with the unit for the software and

the unit to be able to communicate.

TECHNICAL SPECIFICATIONS

Model PP800 PP1100 PP1500T

Capacity (VA) 800VA 1100VA 1500VA

Capacity (Watts) 550W 700W 1000W

Input

Input Voltage Range 85Vac-150Vac

Frequency Range 50/60 Hz +/- 3Hz

Output

On Battery Output Voltage Pure Sine Wave at 120Vac +/- 7%

On Battery Output Frequency 47-53Hz for 50Hz nominal, 57-63Hz for 60Hz nominal

Overload Protection On Utility: Circuit Breaker, On Battery: Internal Current Limiting

Surge Protection and Filtering

Lightning / Surge Protection Yes

Network Protection RJ45 (One In/One Out)

Physical

Total # of UPS Receptacles (7) NEMA 5-15R

Maximum Dimensions 30.9cm*14.1cm*18.4cm

Weight (Kg) 12.8 14.6 15.5

Battery

Sealed Maintenance Free Lead Acid Battery 12V / 8AHx2 12V / 10AHx2 12V / 10AHx2

Hot Swappable Battery Yes

Typical Recharge Time 8 Hours

Warning Diagnostics

Indicators Power On, Using Battery, Boost, Buck

Audible Alarms On Battery, Low Battery, Overload

Environmental

Operating Temperature +32°F to 95°F ( 0° °C to 35 C )

Operating Relative Humidity 0 to 95% NON-CONDENSING

Communication

PowerPanel Plus

TM Software Windows 98/ME/2000/NT/XP, Server 2003, Mac OSX, Linux

Management

Auto-Charger/ Auto-Restart/ USB Yes

SNMP/HTTP Network Optional

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	PP1100SW
Vægt:	14514 g
Responstid:	4 ms
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Ethernet LAN-porte (RJ-45):	1
Antal USB 2.0-porte:	1
Driftstemperatur (T-T):	32 - 95 °F
Dimensioner (BxDxH):	140 x 317.5 x 184 mm
Udgangseffekt:	700 W
Certificering:	UL1778, cUL, FCC DOC Class B
Indgangsfrekvens:	50/60 Hz
Lydalarmer:	Ja
Input forbindertype:	NEMA 5-15P
Antal serielle porte:	1
Vægt (efter britisk standard):	32 Pund
Output-forbindere:	NEMA 5-15R
Dimensioner (BxDxH) (efter britisk standard):	5.5 x 12.5 x 7.25 "
Modem-porte (RJ-11):	1
Overspænding energivurdering:	1796 J
Output strømkapacitet (VA):	1.1 kVA
Typisk backup tid ved halv styrke:	18 min.
Typisk backup tid ved fuld styrke:	7 min.
Udskiftningsbatteri:	BB - BP10-12