CyberPower PR1500LCDRT2UTAA Manual

CyberPower Uafbrydelig strømforsyning (UPS) PR1500LCDRT2UTAA

Læs nedenfor 📖 manual på dansk for CyberPower PR1500LCDRT2UTAA (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

The LCD displays detailed

information on the UPS status

and current power conditions

to alert you to potential power

problems before the affect

your equipment. Note! All

related UPS information is

based on that you should turn

on the UPS.

Smart App Sinewave Series

PR1000LCDRT2U/PR1000LCDRTXL2U

PR1500LCDRT2U/PR2200LCDRT2U

User’s Manual

K01-0000057-05

This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Please read

and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install,

or operate.

CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection. DO NOT plug the UPS into an

outlet that is not grounded. If you need to power-drain this equipment, turn off and unplug the unit.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! Under no circumstances this unit should be used for medical

applications involving life support equipment and/or patient care.

CAUTION! The battery can power hazardous components inside the unit, even when the AC input power is disconnected.

CAUTION! The UPS should be near the connected equipment and easily accessible.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area, free of conductive

contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of an electric shock, do not remove the cover, except to service the battery. There are no user serviceable parts

inside, except for the battery.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a

computer component.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not use with or near aquariums. Condensation from

the aquarium can come in contact with metal electrical contacts and cause the machine to short out.

CAUTION! DO NOT USE WITH LASER PRINTERS! The power demands of laser printers are too large for a UPS.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following.

(1) UPS Unit; (1) User's Manual for UPS; (2) Rack mount Brackets; (2) Stands; (2) Skids; (1) Telephone Cable (black); (1) Emergency Power Off

Cable (gray); (1) PowerPanel® Business Edition Software CD; (2) Serial Interface Cable (DB-9); (1) USB A+B type cable; (1) Warranty

Registration Card.

OVERVIEW

The provides automatic PR1000LCDRT2U/PR1000LCDRTXL2U/PR1500LCDRT2U/PR2200LCDRT2U

voltage regulation for inconsistent utility power. The features 2060 Joules, and PR1000LCDRTXL2U

PR1000LCDRT2U / PR1500LCDRT2U/PR2200LCDRT2U features 1874 Joules of surge protection, and

provides battery backup during power outages. The PR1000LCDRT2U/PR1000LCDRTXL2U/

PR1500LCDRT2U/PR2200LCDRT2U ensures consistent power to your computer system and its included

software will automatically save your open files and shutdown your computer system during a utility power

loss.

AUTOMATIC VOLTAGE REGULATOR(AVR)

The can stabiliz the consistent utility power. The utility power PR1000LCDRT2U/PR1000LCDRTXL2U/PR1500LCDRT2U/PR2200LCDRT2U

may be damaging to important data and hardware, but Automatic Voltage Regulation helps the computer not experience dangerous voltage

levels. Automatic Voltage Regulator automatically regulates low or high voltages to keep equipment working at safe AC power levels (110/120V)

without switching to battery. Your equipment can operate normally even meet the power problems, such as, shout brownouts and blackouts. The

unit’s powerful sealed lead-acid batteries will provide power only if the incoming voltage drops below 80V or increases above 150V.

SYSTEM BLOCK DIAGRAM

HARDWARE INSTALLATION GUIDE

1. Battery charge loss may occur during shipping and storage. For the first time the UPS is used, it’s strongly

recommended to charge batteries for at least eight hours is recommended to ensure that the batteries’ maximum

charge capacity. To recharge the batteries, simply make the UPS plugs into an AC outlet.

2. When you use the included software, connect either the serial or the USB cable between the computer and

the corresponding port on the UPS. Note: If the USB port is used, the serial port will be disabled. They cannot be

used simultaneously. The computer with the PowerPanel® Business Edition S/W connects to the USB port or the

Serial port on the UPS. It can control the operating schedule, battery test, outlet, etc. and get information on the

UPS status. However, other computers with PowerPanel® Business Edition S/W can only get UPS status

information via a LAN connection.

3. With the UPS off and unplugged, connect your computer, monitor, and any externally powered data storage

device (Hard drive, Tape drive, etc.) into the outlets. DO NOT plug a laser printer, copier, space heater, vacuum,

paper shredder or other large electrical device into the UPS. The power demands of these devices will overload

and possibly damage the unit.

4. To protect a fax, telephone, modem line or network cable, connect the telephone or network cable from the

wall jack outlet to the jack marked “IN” of the UPS. Then, connect a telephone cable or network cable from the

jack marked “OUT” on the UPS to the modem, computer, telephone, fax machine, or network device.

5. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air

conditioner, refrigerator, copier, etc.). Avoid using extension cords.

6. Press the power switch to turn the UPS on. The Power-On indicator light will illuminate. If an overload is

detected, an audible alarm will sound and the UPS will emit one long beep. In order to reset it, turn the unit off

and unplug some equipment from outlets. Make sure your equipment carry a load current within the unit’s safe

range, (refer to the technical specifications), and then turn the unit on.

7. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the battery will

be automatically charging, even when the unit is switched off!

8. To always maintain an optimal battery charge, leave the UPS plugged into an AC outlet at all times.

9. Before storing the UPS for an extended period of time, turn the unit OFF. Then cover it and store it with the

batteries fully charged. Recharge the batteries every three months or so, to ensure good battery capacity and

long battery life; further, this might also prevent damage to the unit from an unlikely battery leakage.

10. The unit provides one Primary Serial Port (I), Secondary Serial Port (II), and one USB port, (paired with the

Primary Serial Port), to allow connection and communication between the unit and any attached computers. The

Primary Serial Port (I) as well as its paired USB port allow for bi-directional communication among the UPS and

the primary connected computer running the PowerPanel

® Business Edition S/W provided. The UPS can control

the computer’s shutdown in case of an emergency, and at the same time, the computer can monitor the UPS and

alter its various programmable parameters. On the other hand, secondary Serial Port II only allows the UPS to

initiate the connected computer’s graceful auto-shutdown in case of an emergency.

11. EPO (Emergency Power Off) Port:

Use the provided gray cable to connect to a special EPO contact switch. Follow the appropriate circuit diagram

below to wire the cable to your EPO configuration. The EPO remote switch is a switch installed in an outside area,

connected to the unit via an ordinary RJ-11 phone line. In case of an emergency, it can be used to immediately

cut-off power from the UPS.

FRONT / REAR PANEL DESCRIPTION

1 Power Switch.

Master on/off switch for equipment connected to the UPS.

2. Power On Indicator

Indicates that the AC utility input power’s condition is normal and

that the UPS outlets are providing power, free of surges and spikes.

3. LCD Module Display

LCD shows all the UPS information with icons and messages.

4 LCD Display Toggle Button .

Used to select among a variety of information the LCD can display.

5 Battery Backup Protected Outlets .

The unit provides a total of eight outlets with battery backup and

surge protection. They ensure that connected equipment will keep

an uninterrupted operation over a period of time, during a power

failure.

Critical /Non-critical

It is possible to program the unit in a way so that the outlet block

marked as “non-Critical”, (4 ports), will stop the provision of power

to connected equipment after a certain period of time, thus making

more runtime available for the equipment connected on the outlets

marked as “Critical”, (2 ports). In other words, the user can

establish runtime priority for certain connected equipment,

maximizing its “availability” during a prolonged power outage. This

type of control takes place with the use of the provided

PowerPanel® Business Edition S/W.

6 Input Power Cord .

Connect the AC Power cord to a properly wired and grounded

outlet.

7 Output Circuit Breaker.

This circuit breaker serves to provide output overload and fault

protection.

8 Input Circuit Breaker .

This circuit breaker serves to provide input overload and fault

protection.

Contact your dealer or call the number in this manual for information on battery replacement. The part numbers of internal battery are for RBP832

PR1000LCDRT2U/PR1000LCDRTXL2U/PR1500LCDRT2U RBP842 for PR2200LCDRT2U PR1000LCDRTX2U, . For external battery pack of ,

the part number is . BP48V45ART2U

Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery. Service the battery under the supervision of

personnel knowledgeable of batteries and their precautions . Servicing the battery can only be performed by trained personnel.

Replacement of batteries located in an OPERATOR ACCESS AREA.

CAUTION! When replacing batteries, replace with the same number of the following battery: BP7-12(BB) for PR1000LCDRT2U/

PR1500LCDRT2U/ PR1000LCDRTXL2U, PR2200LCDRT2UHR9-12(BB) for

CAUTION! Risk of Energy Hazard, 12 V, maximum 7 Ampere-hour(BP7-12) or 9 Ampere-hour battery(HR9-12). Before replacing batteries,

remove conductive jewelry such as chains, wrist watches, and rings. High energy through conductive materials could cause severe burns.

CAUTION! Risk of battery explosion, if battery is replaced by an incorrect type. Dispose of used battery according to the instructions.

CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit overcurrent protection in

accordance with the National Electric Code, ANSI/NFPA 70.

CAUTION! PR1000LCDRTXL2U For model can be provided with a maximum of four extension battery packs.

CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.

CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in a fire, as they may explode. Follow all local

ordinances regarding proper disposal of batteries.

CAUTION! Do not open or mutilate the batteries. Release electrolyte is harmful to the skin and eyes and may be toxic.

CAUTION! A battery can present a high risk of short circuit current and electrical shock.

Take the following precautions before replacing the battery:

1. Remove all watches, rings or other metal objects.

2. Only use tools with insulated handles.

3. Do not lay tools or metal parts on top of battery or any terminals.

4. Wear rubber gloves and boots.

5. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source of ground. CONTACT WITH A GROUNDED

BATTERY CAN RESULT IN ELECTRICAL SHOCK! The likelihood of such shock will be reduced if such grounds are removed during installation

and maintenance (applicable to a UPS and a remote battery supply not having a grounded circuit)

INPUT voltage meter: This meter measures the AC voltage from the wall outlet. The INPUT voltage readout

is used to identify the input voltage information. This can be used as a diagnostic tool to identify poor-quality

input power. Units are listed in V (Volts). When the UPS connect to any equipment, the AVR can provide a

stable 110/120V power output. In the event of a complete loss of power, severe brownout, or over voltage,

the UPS relies on its internal battery to back up to supply a consistent 110/120V output.

OUTPUT voltage meter: The Output Voltage screen measures, in real time, the AC voltage that the UPS is

providing to your connected equipment via the UPS outlets. Units are listed in V (Volts).

ESTIMATE RUN TIME: The Estimated Runtime Screen displays how many minutes of runtime can be

expected of the UPS if it were to experience a power outage. When runtime becomes shorted, the battery

capacity will decrease; (battery capacity bar indicator will be falling.) Note: The number displayed may be

less than actual runtimes for low loads.

NORMAL icon: This icon illuminates when the UPS is working under normal conditions.

BATTERY icon: When there is a severe brownout or blackout, this icon will appear followed by an alarm,

(two short beeps), indicating that the UPS is now working using its internal batteries. Once the batteries are

run out of power, (over a period of time), a constant alarm will sound. If this happens and main power has not

been restored, it is recommended that you save your files and turn off your equipment manually as soon as

possible.

Automatic Voltage Regulation (AVR) icon: This icon will appear when the unit is automatically regulating

low or high AC input line voltage conditions, without resulting to the use of battery power.

SILENT MODE icon: This icon appearing indicates that the buzzer will not be beeping while in battery operating mode. During Silent mode, the

unit’s alarm does not sound until the Battery Capacity falls to < 20%.

OVER LOAD icon: This icon will appear followed by an alarm, indicating that an overload condition has been reached. To recover from the

overload condition, start unplugging your equipment from the UPS outlets until the icon disappears and the alarm stops.

FAULT icon: When activated indicates a system fault error. Please refer to the troubleshooting table for possible causes and solutions.

BATT. CAPACITY meter: BATT. CAPACITY is shown as a bar chart; each segment indicates approximately a 20% of battery capacity.

LOAD CAPACITY: Load CAPACITY is shown as a bar chart; each segment indicates approximately a 20% of load capacity.

IMPORTANT SAFETY WARNINGS

INSTALLING YOUR UPS SYSTEM

LCD STATUS DEFINITION

BATTERY REPLAC

MENT

9. USB port.

This is a connectivity port allowing communication and control among

the UPS and the connected computer. You should install on your

computer the PowerPanel® Business Edition S/W appropriate to the

operating system you are using.

10. Protected Communication Ports RJ11/RJ45

Ports protect standard single line modem, fax, telephone line or network

cable.

11. Site Wire Fault Indicator

This LED will illuminate to warn the user that a wiring problem exists

within the AC receptacle, such as a bad ground or reversed wiring. If

illuminated, disconnect all equipment and contact an electrician to

ensure outlet is properly wired.

12. Coax/Cable/DSS Surge Protection

The Coax/Cable/DSS surge protection ports will protect any cable

Modem, CATV converter or DSS receiver.

13. Serial Port I

Serial port allows connection and communication between the UPS and

the computer.

14. Serial Port II

Serial Port II relays information to equipment that can utilize a contact

closure UPS.

15. SNMP/HTTP Network slot

Remove the cover panel to install optional SNMP that allows remote

monitoring and control of your UPS on a network.

16. EPO (Emergency Power Off) Port:

Allow for an emergency UPS Power-Off from a remote location.

BASIC OPERATION

When you first receive the

unit, plug in the unit to fully

charge the battery.

The primary computer with

PowerPanel® Business

Edition software connected

to the UPS with either a

serial cable or a USB cable.

The equipment can

read information

via dry contact.

Dry connect is controlled by the PowerPanel

Software, please

go to www.cyberpowersystems.com for free download.

* Both USB and Serial cannot be used simultaneously. NOTE:

Unplug the unit and turn Power

Off when first connecting your

computer and peripherals.

1. Remove the front panel on the

right side. 2. Remove the two retaining screws of

the cable protection cover then remove

the cover.

3. Remove the two retaining screws of

the cable connectors.

4. Disconnect the black and red

cable

5. Remove the three retaining screws. 6. Pull out the old battery pack and replace.

Reassemble the retaining screws, covers, black and

red cable, and front panel in the reverse sequence

of the above steps. Recharge the unit for 4-8 hours

to ensure maximum UPS battery runtime.

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	PR1500LCDRT2UTAA
Bredde:	438.15 mm
Dybde:	400.05 mm
Højde:	88.9 mm
Vægt:	25401 g
Produktfarve:	Sort
Skærmtype:	LCD
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Reolbeslag/tårn
Opbevaringstemperatur (T-T):	-15 - 45 °C
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Antal USB 2.0-porte:	1
Driftstemperatur (T-T):	0 - 35 °C
Udgangseffekt:	1000 W
Certificering:	UL1778, cUL 107.1, FCC DOC Class B
LED-indikatorer:	Ja
Kabellængde:	3 m
Batteritype:	12V/7AH
Opladningstid for batteri:	8 t
Bæredygtighedscertifikater:	RoHS
Medfølgende software:	PowerPanel
Driftshøjde:	0 - 3000 m
Ikke-drift højde:	0 - 15000 m
Indgangsfrekvens:	50/60 Hz
Antal battericeller:	4
Lydalarmer:	Ja
Antal serielle porte:	2
Strømstik:	NEMA 5-15P
Nominel udgangsspænding:	120 V
Administrationsplatform:	SNMP/HTTP
Beskyttelse mod overspænding:	Ja
AC udgange, antal:	8 AC stikkontakt(er)
AC stikkontakt typer:	NEMA 5–15R
Overspænding energivurdering:	1780 J
Indgående driftsspænding (maks.):	150 V
Rackkapacitet:	2U
Output strømkapacitet (VA):	1.5 kVA
Indgående driftsspænding (min.):	80 V
Udgangs driftsspænding (min.):	- V
Udgangs driftsspænding (maks.):	- V
Beskyttelsesfunktioner mod strømstød:	Coax, Network, Telephone
Beskyttelse ved overspænding:	Ja
Typisk backup tid ved halv styrke:	18 min.
Typisk backup tid ved fuld styrke:	6 min.
Hot-swap batteri:	Ja
Nødstrøm Off (EPO):	Ja
EMI/RFI støjfiltrering:	Ja