CyberPower Smart App OR1500LCDRT2U Manual

CyberPower Uafbrydelig strømforsyning (UPS) Smart App OR1500LCDRT2U

Læs nedenfor 📖 manual på dansk for CyberPower Smart App OR1500LCDRT2U (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne guide var nyttig for 25 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

OR1500LCDRT2U / OR2200LCDRT2U

User’s Manual

K01-0000307-02

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions that must be followed during installation and maintenance of the UPS and batteries. Please read and

follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or

operate your UPS.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive

contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. Turn off and unplug the unit before

servicing the batteries. There are no user serviceable parts inside except for the battery.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.

CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not

grounded. If you need to de-energize this equipment, turn off and unplug the unit.

CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a computer

component.

CAUTION! Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment,

ANSI/NFPA 75.

CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit over current protection in

accordance with the National Electric Code, ANSI/NFPA 70.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical

applications. use in any circumstance that would affect the operation and safety of life support equipment, medical applications, or DO NOT

patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium. Condensation

from the aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of fire or electric shock, do not use the unit on any transportation

such as airplanes or ships. The effect of shock or vibration caused during transit and the damp environment can cause the unit to short out.

INTRODUCTION

Thank you for selecting a CyberPower Systems UPS product. This UPS is designed to provide unsurpassed power protection, operation and

performance during the lifetime of the product.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS unit (b) User’s manual (c) Rack mount brackets (d) Stands (e)Telephone cable (f) Serial cable (DB-9) (g) USB A+B type cable

OVERVIEW

The OR1500LCDRT2U/OR2200LCDRT2U provides complete power protection from utility power

that isn't always consistent. The OR1500LCDRT2U/OR2200LCDRT2U features surge protection

against power surges and maintenance free batteries for long lasting battery backup during power

outages. In addition to ensuring consistent power to your computer system and the

OR1500LCDRT2U/OR2200LCDRT2U also includes software that will automatically save your open

files and shutdown your computer system during a utility power loss.

AUTOMATIC VOLTAGE REGULATOR

The OR1500LCDRT2U/OR2200LCDRT2U stabilizes inconsistent utility power voltage to nominal

levels that are safe for equipment. Inconsistent utility power may be damaging to important data files

and hardware, but with Automatic Voltage Regulation (AVR), damaging voltage levels are corrected

to safe levels. AVR automatically increases low utility power and decreases high utility power to a consistent

and safe 110/120 volts.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

Ensure that the equipment plugged into the outlets does not exceed the UPS unit’s rated capacity

(1500VA/900W for OR1500LCDRT2U, 2000VA/1320W for OR2200LCDRT2U). If the rated capacities of the

unit are exceeded, an overload condition may occur and cause the UPS unit to shut down or the circuit breaker to

trip.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, to ensure the battery’s maximum charge

capacity, it is recommended that you charge the battery for at least 8 hours. Your UPS is equipped with an

auto-charge feature. When the UPS is plugged into an AC outlet, the battery will automatically charge

whether the UPS is turned on or off.

2. With the UPS unit turned off and unplugged, connect your computer, monitor, and any other peripherals

requiring battery backup into the battery power supplied outlets. DO NOT plug a laser printer, paper

shredder, copier, space heater, vacuum, sump pump or other large electrical devices into the “Battery

and Surge Protected Outlets”. The power demands of these devices may overload and damage the

unit.

3. To protect a fax, phone or modem, connect a telephone cable or network cable from the wall jack outlet to

the IN jack of the UPS. Connect a telephone cable or network cable from the OUT jack of the UPS to a fax

machine, telephone, modem, or network devices.

4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air

conditioner, copier, etc…). The warranty prohibits the use of extension cords, outlet strips, and surge strips.

5. Press the power switch to turn the unit on. The Power On indicator light will illuminate and the unit will “beep”.

If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this,

turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets. Make

sure the circuit breaker is depressed and then turn the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store the UPS for an extended period, cover it and store with the battery fully charged. While in storage, recharge the battery every three

months to ensure battery life.

8. Ensure the wall outlet and UPS are located near the equipment being attached for proper accessibility.

9. Professional Rack Mount UPS provides one serial port, one dry contact and one USB port to allow connection and communication between

the UPS and computers or equipment. USB port and Serial Port l (Primary) allow the simultaneous shutdown of two computer systems. Serial

port ll produces the basic information for the equipment that can utilize a dry contact ups. The Primary computers (with PowerPanel

Business Edition installed) are the computers that you will use to control the UPS and make any changes to the operation of the UPS. When

there is a power failure, the computer which connects to Primary port will start to shut down after a user controlled delay. PowerPanel

Business Edition will save and close any open files to shutting the system down.

DESCRIPTION

1. Power Switch

Used as the master on/off switch for equipment

connected to the battery power supplied outlets.

2. Power On Indicator

This LED is illuminated when the utility power is

normal and the UPS outlets are providing

power, free of surges and spikes.

3. LCD module display

High resolution and intelligent LCD display

shows all the UPS information using icons and

messages. For more information please review

the “Definitions for Illuminated LCD Indicators”

section below.

4. LCD function selection switch

The switch can be used to select the LCD

display contents including input/output voltage

and estimated run time, etc.

5. Battery and Surge Protected Outlet

The unit has eight batteries powered/surge suppression outlets for connected equipment to ensure temporary uninterrupted operation of

your equipment during a power failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum, sump pump or

other large electrical devices into the “Battery and Surge Protected Outlets”. The power demands of these devices may overload

and damage the unit.)

6. AC Input Power Cord

Heavy-duty power cord.

7. Output Circuit Breaker

Resettable circuit breakers provide output optimal overload protection.

8. Input Circuit Breaker

Resettable circuit breakers provide input optimal overload protection.

9. USB Port

The USB port allows connection and communication between the computer and the UPS unit.

10. Communication Protection Ports

Communication protection ports will protect any standard modem, fax, telephone line, network or Ethernet connection (RJ11/RJ45).

11. Wiring Fault Indicator (red)

This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or reversed wiring. If

this is illuminated, disconnect all electrical equipment from the outlet and have an electrician verify the outlet is properly wired. The unit will

not provide surge protection without being plugged into a grounded and properly wired wall outlet.

12. Coax/Cable/DSS Surge Protection

The Coax/Cable/DSS surge protection ports will protect any cable modem, CATV converter, or DSS receiver.

13. Serial Port I (Primary)

The serial port allows connection and communication between the UPS and the computer.

14. Serial Port II (Dry Contact)

Dry contact produces information for equipment that can utilize dry contact signals.

15. SNMP/HTTP Network Slot

Remove the cover panel to install an optional RMCARD to remotely monitor and manage your UPS over a network.

REPLACING THE BATTERY

Replacement of batteries located in an OPERATOR ACCESS AREA.

When replacing batteries, replace with the same number of the following battery: CyberPower / RB1270X4J for the OR1500LCDRT2U,

CyberPower / RB1290X4L for the OR2200LCDRT2U.

CAUTION! Risk of Energy Hazard, 24V, maximum 18 Ampere-hour battery. Before replacing batteries, remove conductive jewelry such as

chains, wrist watches, and rings. High energy conducted through these materials could cause severe burns.

CAUTION! Do not dispose of batteries in a fire. The batteries may explode.

CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It may be toxic.

CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATT ERIES ACCORDING

TO LOCAL REGULATIONS.

 BATTERY REPLACEMENT PROCEDURE:

REMINDER: Batteries are considered HAZARDOUS WASTE and must be di sposed of properly. Most retailers that sell lead-acid batteries

collect used batteries for recycling, as required by local regulations.

1. INPUT voltage meter:

This meter measures the AC voltage that the UPS system is receiving from the utility wall outlet. The UPS is designed, through the use of

automatic voltage regulation, to continuously correct output voltage to connected equipment to a safe 110/120 voltage output range. In the

event of a complete power loss, severe brownout, or over-voltage, the UPS relies on its internal battery to supply consistent 110/120

output voltage. The INPUT voltage meter can be used as a diagnostic tool to identify poor-quality input power.

2. OUTPUT voltage meter:

This meter measures, in real time, the AC voltage that the UPS system is providing to the computer, such as normal line mode, AVR mode,

and battery backup mode. (Note: The OUTPUT voltage meter shows the status of the battery backup outlets.)

3. ESTIMATED RUNTIME:

This displays the run time estimate of the UPS with current battery capacity and load.

4. NORMAL icon:

This icon appears when the UPS is working under normal conditions.

5. BATTERY icon:

During a severe brownout or blackout, this icon appears and an alarm sounds (two short beeps followed by a pause) to indicate the UPS is

operating from its internal batteries. During a prolonged brownout or blackout, the alarm will sound continuously (and the

BATT.CAPACITY meter shows one 20% capacity segment shaded) to indicate the UPS’s batteries are nearly out of power. You should

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY INSTRUCTIONS

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

1. Remove the right side front panel. 2. Remove four screws from battery compartment cover 3. Disconnect the black and red cable

and remove the cover completely off the unit.

4. Insert the new battery pack. Assemble the 5. Install the replacement batteries by connecting the

screws, cover, cable and front panel in the red and the black wire to the same color wires

reverse sequence of above steps. from the battery pack.

Recharge the unit for at least 8 hours to ensure

the UPS performs expected runtime.

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	Smart App OR1500LCDRT2U
Bredde:	438.1 mm
Dybde:	400 mm
Højde:	88.9 mm
Vægt:	21953 g
Produktfarve:	Sort
Skærmtype:	LCD
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Reolbeslag/tårn
Responstid:	4 ms
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 35 °C
Udgangseffekt:	900 W
LED-indikatorer:	Ja
Kabellængde:	0.2 m
Antal understøttede batterier:	4
Opladningstid for batteri:	8 t
Indgangsfrekvens:	47/63 Hz
Antal serielle porte:	2
Strømstik:	NEMA 5-15P
Kølingstype:	Passiv
Modem-porte (RJ-11):	1
AC udgange, antal:	8 AC stikkontakt(er)
AC stikkontakt typer:	NEMA 5–15R
Overspænding energivurdering:	1840 J
Indgående driftsspænding (maks.):	140 V
Rackkapacitet:	2U
Output strømkapacitet (VA):	1.5 kVA
Indgående driftsspænding (min.):	90 V
Udgangs driftsspænding (min.):	- V
Udgangs driftsspænding (maks.):	120 V
UPS topologi:	Interaktivt indgangsstik
Beskyttelsesfunktioner mod strømstød:	Network,Telephone
Beskyttelse ved overspænding:	Ja
Typisk backup tid ved halv styrke:	18 min.
Typisk backup tid ved fuld styrke:	6 min.
Automatisk spændingsregulering (AVR):	Ja