DeWalt D26441K Manual

DeWalt Rysteplaster D26441K

Læs nedenfor 📖 manual på dansk for DeWalt D26441K (6 sider) i kategorien Rysteplaster. Denne guide var nyttig for 24 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/6

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

D26441, 1/4 Sheet Sander

Ponceuse à 1/4 de bande D26441

D26441, Lijadora de 1/4 de lámina

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. LÉASE ESTE INSTRUCTIVO ANTESADVERTENCIA:

DE USAR EL PRODUCTO.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Instructions

WARNING! Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

•Do not operate power tools in explosive atmospheres, such as in the presence of flam-

mable liquids, gases, or dust. Power tools create sparks which may ignite the dust or

fumes.

•Keep bystanders, children, and visitors away while operating a power tool. Distractions

can cause you to lose control.

ELECTRICAL SAFETY

•Grounded tools must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or

modify the plug in any way. Do not use any adaptor plugs. Check with a qualified elec-

trician if you are in doubt as to whether the outlet is properly grounded. If the tools

should electrically malfunction or break down, grounding provides a low resistance path to

carry electricity away from the user. Applicable only to Class I (grounded) tools.

•Double insulated tools are equipped with a polarized plug (one blade is wider than the

other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully

in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to

install a polarized outlet. Do not change the plug in any way. Double insulation elim-

inates the need for the three wire grounded power cord and grounded power supply system.

Applicable only to Class II (double insulated) tools.

•Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

•Don’t expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

•Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged

cords immediately. Damaged cords increase the risk of electric shock.

•When operating a power tool outside, use an outdoor extension cord marked “W-A”

or “W.” These cords are rated for outdoor use and reduce the risk of electric shock. When

using an extension cord, be sure to use one heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-

ber, the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than 0 - 6 18 16 16 14

PERSONAL SAFETY

•Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may result in serious personal injury.

•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,

clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be

caught in moving parts. Air vents often cover moving parts and should also be avoided.

•Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

•Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

•Do not overreach. Keep proper footing and balance at all times. Proper footing and bal-

ance enables better control of the tool in unexpected situations.

•Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

•Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

•Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

•Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

•Disconnect the plug from the power source before making any adjustments, changing

accessories, or storing the tool. Such preventative safety measures reduce the risk of

starting the tool accidentally.

•Store idle tools out of reach of children and other untrained persons. Tools are dan-

gerous in the hands of untrained users.

•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,

with sharp cutting edges are less likely to bind and are easier to control.

•Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

•Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

SERVICE

•Tool service must be performed only by qualified repair personnel. Service or mainte-

nance performed by unqualified personnel could result in a risk of injury.

•When servicing a tool, use only identical replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized parts or failure to follow mainte-

nance instructions may create a risk of electric shock or injury.

Additional Safety Instructions for Sanders

• Accessories must be rated for at least the speed recommended on the tool warning

label. Wheels and other accessories running over rated speed can fly apart and cause injury.

Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

• Hold tool by insulated gripping surfaces when performing an operation where the cut-

ting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make

exposed metal parts of the tool “live” and shock the operator.

• Always wear eye protection and a respirator when sanding.

• Sanding of lead-based paint is not recommended. Precautions To Take WhenSee

Sanding Paint for additional information before sanding paint.

• Do not operate the unit without the dust collection bag.

• Clean your tool out periodically.

• Empty dust bag frequently, especially when sanding resin coated surfaces such as

polyurethane, varnish, shellac, etc. Dispose of coated dust particles according to the finish

manufacturer’s guidelines, or place in a metal can with a tight-fitting metal lid. Remove coated

dust particles from the premises daily. The accumulation of fine sanding dust particles may

self ignite and cause fire.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with approved

safety equipment, such as those dust masks that are specially designed to filter out microscop-

ic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions and

duration of use, noise from this product may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V ..............volts A................amperes

Hz ............hertz W ..............watts

min............minutes ............alternating current

..........direct current no..............no load speed

..............Class II Construction ..............earthing terminal

..............safety alert symbol .../min ........revolutions per minute

SAVE THESE INSTRUCTIONS

COMPONENTS (Fig. 1)

A. On/Off switch E. Vac-adapter

B. Clamp lever F. Paper clamp

C. Base plate/pad G. Paper-limiting ribs

D. Dust collection bag

Motor

Your DEWALT tool is powered by a D WALT-built motor. Be sure your power supply agrees withE

the nameplate marking (Volts, 120 AC only). A Voltage decrease of more than 10% will cause

loss of power and overheating. All tools DEWALT tools are factory tested; if this tool does not

operate, check the power supply.

Attaching Abrasive Paper (Fig. 1, 2)

CAUTION: Turn off and unplug the tool before making any adjustments or removing

or installing attachments or accessories. Be sure the switch is in the OFF position.

Your sander is designed to use 1/4-sized sanding sheets. Pre-cut 4-1/2" x 5-1/2" sandpaper is

available at extra cost.

TO MAKE 4-1/2" X 5-1/2" SANDPAPER

a. Cut full-sized (9" x 11") sandpaper into 1/4 sheets of 4-1/2" x 5-1/2".

b. Cut 1/2 sheet sandpaper into two 4-1/2" x 5-1/2" sheets.

For normal operation, assemble the abrasive paper to your unit as follows:

1. Soften the stiff sandpaper by pulling it over the 90° edge of a table or other straight edge, as

shown in Figure 2. Concentrate on softening the edges to be clamped.

2. Release the clamp by pulling up on the clamp lever (B) and disengaging it from the tab on the

base plate/pad (C).

3. Insert the 4-1/2" edge of the abrasive paper under the front paper clamp (F) until it hits the

paper-limiting ribs (G). Close the front paper clamp and hook it into the lock position behind

the tab on the base plate/pad.

4. Stretch paper over sanding pad and insert under the opposite clamp in the same way.

5. If you are using the dust extraction feature, perforate the sandpaper (see Paper Punch).

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more DEWALT power tools: the yellow and black color

scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box

configuration; and the array of lozenge-shaped humps on the surface of the tool.

Questions? See us in the World Wide Web at www.dewalt.com

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Rysteplaster
Model:	D26441K

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt D26441K stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Rysteplaster DeWalt Manualer

DeWalt DW421K Manual

15 Maj 2024

DeWalt DWMT70781L Manual

6 Marts 2024

DeWalt D26422 Manual

2 Februar 2024

DeWalt DWE6423 Manual

2 Januar 2024

DeWalt DWMT70780 Manual

27 August 2023

DeWalt DCG413 Manual

8 December 2022

DeWalt DW411K Manual

30 November 2022

DeWalt D26441K Manual

27 November 2022

DeWalt DWE4357 Manual

23 November 2022

DeWalt DWE6421K Manual

21 November 2022

Rysteplaster Manualer

Nyeste Rysteplaster Manualer

Craftsman CMCW223 Manual

15 November 2024

Metabo SM 18 LTX BL Manual

24 September 2024

Prowork PDS 125 Manual

12 September 2024

Prowork PSS 135 Manual

12 September 2024

Prowork PSS 150 Manual

12 September 2024

Prowork PD 150 Manual

12 September 2024

Tryton TMT810A Manual

11 September 2024

Einhell EX-E 125 E Manual

4 September 2024

Skil 7280 DA Manual

11 August 2024

RIKON 50-1428 Manual

2 August 2024