DoughXpress DX-BMIH-18/36 Manual
DoughXpress
Post maskine
DX-BMIH-18/36
Læs nedenfor 📖 manual på dansk for DoughXpress DX-BMIH-18/36 (2 sider) i kategorien Post maskine. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
MODEL DX-BMIH-36/18/9
Manual Dough Divider
The DoughXpress DX-BMIH Dough Divider is simple to operate, and
very accurate. The removable divider head assemblies can be cleaned
daily, either by hand washing, or by placing into a dish or pan washer.
Instructions for removal of the divider assembly are found inside this
manual. Removal takes only seconds, and without the need for tools.
This Dough Divider will divide a single large piece of dough into either
36, 18 or 9 equal pieces, the weight of each piece being determined by
the weight of the large piece placed into the pan initially, and the head
assembly being utilized.
DOUGH DIVIDING PROCEDURE
A simple formula for determining the size of the initial piece of dough is
to decide what each piece of dough should weigh. Multiply this weight by
36, 18 or 9 depending on head assembly, then divide by 16 (ounces),
and you will have the weight (in pounds) of the initial piece of dough
needed to be placed into the pan.
Example: Each piece needs to weigh 2 ounces.
2 ounces x 36 (pieces) = 72 ounces
72 (ounces) ÷ 16 (ounces) = 4 lbs. 8-ounces.
(See Dough Weight Chart on back for additional examples)
S
T
E
P
1
S
T
E
P
2
S
T
E
P
3
Head Assembly & Parts Description Machine Parts Description w/o Head Ass’y.
LIST OF PARTS
Item Qty. Description Part Number
1 1 36-Part Divider C4-141-0001
1 *18-Part Divider * C4-141-0002
1 * 9-Part Divider * C4-141-0046
2 4 36-Part Center Plug A4-139-0001
2 *18-Part Center Plug * A4-139-0004
1 * 9-Part Center Plug * A4-139-0057
3 12 36-Part Intermediate Plug A4-139-0002
6 *18 Part Intermediate Plug * A4-139-0005
3 * 9 Part Intermediate Plug * A4-139-0058
4 20 36-Part Outer Plug A4-139-0003
10 *18-Part Outer Plug * A4-139-0006
5 * 9 Part Outer Plug * A4-139-0059
5 36 36 & 9-Part Plug Stem B4-054-0003
36 *18-Part Plug Stem * B4-054-0001
6 1 36-Part Divider Plate C4-147-0008-P
1 *18-Part Divider Plate * C4-147-0009-P
7 1 Plug Plate C4-147-0002-P
8 6 Flat Head Phillips Screw 22-E-0407
9 1 Lock Plate C4-147-0003
10 1 Cover Plate C4-147-0004
11 2 Captured Screw P4-927-0001
12 1 Pin 73-E-0620
* 18 or 9-Part Heads (Not Shown)
SHOWN:
36-Part Head
Assembly Drawing;
with 36, 18 & 9-Part
Description and
Part Numbers
Item Qty. Description Part Number
1 1 Yoke C4-088-0001-P
2 2 Bushing P4-909-0001
3 2 Bushing P4-909-0003
4 1 Base C4-030-0001-P
5 4 Capscrew 12-E-0608
6 3 Bushing Half A4-024-0001
7 1 Ram with Rack B4-003-0003
8 1 Ram Pin A4-066-0001
9 2 Bushing P4-909-0002
10 4 Screw 22-E-0407
11 1 Gear Shaft A4-053-0003
12 1 Gear A4-003-0002
13 2 Key S-L-03-03-16
14 2 Spacer A4-023-0002
15 1 Lever w/Counterweight B4-045-0001-P2
16 1 Slotted Set Screw 31-E-0402
17 1 Yoke Cover B4-063-0119
18 2 Socket Set Screw 29-Y-0605
19 1 Socket Set Screw 29-Y-0607
Item Qty. Description Part Number
20 1 Cover A4-063-0002
21 1 Handle A4-092-0001
22 1 Hand Grip P4-939-0001
23 1 Socket Set Screw 29-Y-0610
24 3 Set Screw Plug A4-139-0007
25 1 Trip Lever B4-045-0004-P
26 2 Wear Plate A4-147-0006-P
27 2 Screw 22-E-0304
28 2 Bushing P4-909-0005
29 2 Pivot Bolt A4-033-0001
30 2 Spindle A4-145-0001
31 2 Retaining Ring P4-957-0001
32 2 Spindle Spring A4-082-0002
33 1 Trip Plate C4-147-0005-P
34 2 Pivot Tab A4-146-0001-P
35 2 Knob P4-939-0002
36 1 Pan (Not Shown) B4-149-0001
37 1 Plug A4-139-0024
38 1 Bushing P4-909-0031
39 4 Yoke cover Screw 23-E-0406
LIST OF PARTS
Page 5 Page 6
OPERATING INSTRUCTIONS
Step 1: Place the large dough piece to be divided into a lightly dusted
Pan then place the Pan into the Machine. Before placing the PanNote:
into the Machine, press the dough by hand so it completely covers the
bottom of the Pan.
Step 2: After placing the Pan into the Machine, pull down on the
Handle and exert a firm pressure for 3-4 seconds to uniformly flatten the
dough inside the Pan.
Step 3: Slightly relax the pressure on the Operating Handle and push
down on the Trip Lever to release the Cutting Knives from the Head
Assembly. Next, push the Operating Handle all the way down, and the
Knives will cut the dough into evenly divided pieces.
Raise the Operating Handle to the start position, remove the Pan and
dump out the divided dough pieces. You are ready to repeat the
procedure.
Tip: For sticky dough products, line the bottom of the Pan with a
circular piece of parchment paper. The paper can be used repeatedly.
1201 E. 27th Terrace • Pittsburg, KS 66762 • U.S.A.
Ph: (620) 231-8568 • Fax: (620) 231-1598 • E-Mail: mail@hixcorp.com • Website: www.doughxpress.com
Produkt Specifikationer
| Mærke: | DoughXpress |
| Kategori: | Post maskine |
| Model: | DX-BMIH-18/36 |
Har du brug for hjælp?
Hvis du har brug for hjælp til DoughXpress DX-BMIH-18/36 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Post maskine DoughXpress Manualer
19 August 2024
14 August 2024
13 August 2024
12 August 2024
12 August 2024
11 August 2024
10 August 2024
Post maskine Manualer
- Post maskine Bosch
- Post maskine SilverCrest
- Post maskine Philips
- Post maskine Rommelsbacher
- Post maskine Kenwood
- Post maskine Witt
- Post maskine Ernesto
- Post maskine Livoo
- Post maskine Klarstein
- Post maskine Bartscher
- Post maskine Ariete
- Post maskine C3
- Post maskine Cuisinart
- Post maskine CaterChef
- Post maskine G3 Ferrari
- Post maskine Gourmetmaxx
- Post maskine Hamilton Beach
- Post maskine Unold
- Post maskine Bellini
- Post maskine Imperial
- Post maskine Laica
- Post maskine Trebs
- Post maskine Beper
- Post maskine Emeril Lagasse
- Post maskine Arendo
- Post maskine Waring Commercial
- Post maskine Manta
- Post maskine Nutrichef
- Post maskine Farberware
- Post maskine Marcato
- Post maskine Ronco
- Post maskine Girmi
- Post maskine Riviera And Bar
- Post maskine CombiSteel
- Post maskine Proluxe
- Post maskine Estella
- Post maskine Weston
- Post maskine Imperia
- Post maskine Stilfer
- Post maskine Tescoma
Nyeste Post maskine Manualer
13 September 2024
6 September 2024
3 September 2024
3 September 2024
1 September 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
30 August 2024