DPW Design Limit Manual


Læs nedenfor 📖 manual på dansk for DPW Design Limit (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Limit L-2, Triple Limiter
The L-2 is a three individual soft knee limiter module in Eurorack format. An all analog unit.
It can be used for audio signal manipulation or as a utility module for control voltages. The three
channels can be AC or DC coupled.
It can be used for normal limiting/compression but also for creative wave shaping.
Compared to the previous L-1 module the only change is added noramling between the channels.
The soft knee of the limiter is actually 8 consecutive soft knees for each channel starting at -6dB
compared to 5V and spread evenly up to 5V.
The limiter will brick wall limit to +/- 5V both in AC and DC mode.
In other words it gradually increase the compression from +8dBu and brick wall limits at +14dBu.
Controls
For each channel there is a volume control that sets how hard the limiter
is driven.
When the knob is at 9 o'clock what passes through is almost unaffected only
compressing high peaks. Turning the the knob to full on will give 5 times
amplification drive in to the limiter, giving a rounded distorted sound.
The three channels are completely independent.
AC/DC coupling for Lim1 and Lim2 is done with the switch on the panel.
AC/DC coupling for Lim3 is done by a jumper on the back of the module.
When the jumper is mounted Lim3 is DC coupled.
The module is delivered with the jumper mounted.
If you want higher compression than just one limiter you can chain
several limiters, this is pre-patched via normaling.
If nothing is connected to IN on channel 2 or 3 they will get their input
from the channel above as shown by the dotted lines on the front
panel. This is also so you easily can get tree different compressed
versions of the same sound out.
Connecting something in on 2 or 3 will disconnect the noramling.
Device specs
Module size: 6 hp wide, 32 mm deep with power connector.
Input impedance: 20 kohm
Output impedance: 1 kohm
Power requirements: +/- 12V. Max power consumption +/- 20 mA
Connect the power cable with the red stripe (-12V) down.
The unit is protected for reverse power.
DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden
www.dpw.se MAN-L-2 Rev B


Produkt Specifikationer

Mærke: DPW Design
Kategori: Ikke kategoriseret
Model: Limit

Har du brug for hjælp?

Hvis du har brug for hjælp til DPW Design Limit stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret DPW Design Manualer

DPW Design

DPW Design Zero 2 Manual

24 August 2024
DPW Design

DPW Design Shape Manual

24 August 2024
DPW Design

DPW Design Switch Manual

24 August 2024
DPW Design

DPW Design Limit Manual

24 August 2024
DPW Design

DPW Design AV2 Manual

24 August 2024
DPW Design

DPW Design Mix Manual

24 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Philips

Philips Senseo HD7002 Manual

24 December 2024
Philips

Philips GoGear PAC009 Manual

24 December 2024
Koenic

Koenic KVRWD 21624 Manual

24 December 2024
Koenic

Koenic KAP 2523 Manual

24 December 2024
Koenic

Koenic KWC 13725 Manual

24 December 2024
Koenic

Koenic KAF 2110 W Manual

24 December 2024
Philips

Philips HD9921 Manual

24 December 2024
Philips

Philips Senseo HD7008 Manual

24 December 2024