Drayton Erie Digistat + Manual

Drayton Erie Termostat Digistat +

Læs nedenfor 📖 manual på dansk for Drayton Erie Digistat + (2 sider) i kategorien Termostat. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Digistat+ & Digistat+RF

Room Thermostat

Models:

30002 / RF601

Invensys Controls Europe

Technical Helpline: +44 (0) 845 130 7722

www.draytoncontrols.co.uk

Installation / User Guide 06490056001 (09/05)

User Guide

What is a room thermostat?

... An explanation for householders

A room thermostat simply switches the heating system on

and off as necessary. It works by sensing the air temperature,

switching on the heating when the air temperature falls below

the thermostat setting, and switching it off once this set

temperature has been reached.

Turning a room thermostat to a higher setting will not make

the room heat up any faster. How quickly the room heats up

depends on the design of the heating system, for example, the

size of boiler and radiators.

Neither does the setting affect how quickly the room cools

down. Turning a room thermostat to a lower setting will result

in the room being controlled at a lower temperature, and saves

energy.

The heating system will not work if a time switch or programmer

has switched it off.

The way to set and use your room thermostat is to ﬁnd the

lowest temperature setting that you are comfortable with,

and then leave it alone to do its job. The best way to do this

is to set the room thermostat to a low temperature – say 18ºC

– and then turn it up by one degree each day until you are

comfortable with the temperature. You won’t have to adjust the

thermostat further. Any adjustment above this setting will waste

energy and cost you more money.

If your heating system is a boiler with radiators, there will

usually be only one room thermostat to control the whole

house. But you can have different temperatures in individual

rooms by installing thermostatic radiator valves (TRVs) on

individual radiators. If you don’t have TRVs, you should choose

a temperature that is reasonable for the whole house. If you do

have TRVs, you can choose a slightly higher setting to make sure

that even the coldest room is comfortable, then prevent any

overheating in other rooms by adjusting the TRVs.

Room thermostats need a free ﬂow of air to sense the

temperature, so they must not be covered by curtains or

blocked by furniture. Nearby electric ﬁres, televisions, wall or

table lamps may prevent the thermostat from working properly.

Your new thermostat with digital display.

LCD Display

Dial

Set button Battery Compartment

Thermostat Display – Features & Characters

2 22

ºc

SET

ºc

f6 0

ºc

C2 5

ºc

A demand for heat is

shown by a flame

symbol on the display,

i.e. the thermostat is

calling for heat to bring

the room up to or

maintain it at the

desired temperature.

During normal

operation the display

shows the actual room

temperature.

When the desired

temperature is being

adjusted the word 'SET'

is shown on the

display.

The display designates the model type selected, i.e.

Low battery warning

is shown by a flashing

battery symbol on the

display.

An RF Model is shown

by an antenna symbol

on the display. (No

symbol denotes a

wired model).

2 1

ºc

F = Frost Thermostat, C = Cylinder Thermostat, P = Pipe Thermostat

Room Thermostat

FEATURES

This product has the following user adjustable settings

• Required room temperature (temperature setpoint)

• Preset temperature setting - Advanced feature

• Minimum & Maximum temperature settings - Advanced feature

Simple Setting or Operating

To set the required room temperature

• The display normally shows the current room

temperature to within 0.5ºC

• To adjust the required temperature, turn the

dial clockwise to increase or anti-clockwise to

decrease, (1 click = 1ºC), the LCD will display

the temperature setpoint as it is being adjusted

and ‘SET’ will be displayed. After a few seconds

the display will return

to normal operation and

will display the actual room temperature.

While adjusting the temperature during normal

operation, when you reach the maximum or

minimum possible setting the display will ﬂash to

indicate you cannot adjust the product further.

ADVANCED FEATURES

Adjusting the Setpoint using the Preset Temperature Mode

Change the temperature at the press of a button, for example, if

you are going out to the shops for an hour you can reduce the

temperature to save energy and then when you press the button

again on your return the setpoint will return to the previous level.

• To adjust the setpoint to the preset (or Setback) temperature,

press the ‘Set’ button during normal operation and the product

will go into Preset mode.

NB. This feature can be used to quickly adjust the temperature

setpoint to a setback temperature for economy operation if for

example, ‘Preset Temperature = 15ºC’. Or alternatively to a comfort

setpoint if ‘Preset Temperature = 21ºC’.

• Once the setpoint has been changed to the preset (or setback)

temperature by pressing ‘Set’ the display will show the ‘Preset

Temperature’ and ‘SET’ will be ﬂashing in the display as shown,

ºc

p I

H i

E S

E I

E 2

E L

C Y

i 0

ºc

i 5

ºc

2 4

ºc

9 0

ºc

6 0

ºc

4 0

ºc

3 0

ºc

2 0

ºc

7 0

ºc

p I

0 0

C Y

E S

E L

SET

i 5

ºc

SET

2 2

ºc

‘SET’ will ﬂash for approximately 5 seconds and during this time

the ‘Preset Temperature’ can be altered by rotating the dial.

•

The product will remain in the Preset mode. Once 5 seconds

have elapsed (since the last dial adjustment) the word ‘SET’ will

stop ﬂashing on the display as shown,

ºc

p I

H i

E S

E I

E 2

E L

C Y

i 0

ºc

i 5

ºc

2 4

ºc

9 0

ºc

6 0

ºc

4 0

ºc

3 0

ºc

2 0

ºc

7 0

ºc

p I

0 0

C Y

E S

E L

SET

i 5

ºc

SET

2 2

ºc

The product is still in the Preset mode.

06490056001 ISS E 06490056001 ISS E

Tear hereTear here

Location

Room Thermostat

1.5m

Care should be taken to mount the thermostat in a position which

is not subject to direct sunlight or draughts. Preferably it should be

mounted on an inside wall about 1.5m (5ft) above the ﬂoor in a

position where it can respond to room temperature but away from

the direct inﬂuence of radiators or other appliances giving off heat.

Before Installation

If you do not have the knowledge to install the thermostat safely then

you must arrange for a competent electrician to install it for you.

Wiring must conform to the current IEE regulations.

Prior to commencing the installation you must ensure the mains

supply is switched off.

Remove battery

compartment

Loosen screw

Standard cable entry is from the rear, but if surface wiring, from the

top or bottom, is to be used, or extra space for cabling is required,

use the optional Pattress box (sold separately).

WIRING

Room Thermostat (not RF models)

External

Sensor

OFF ON L

Not required for RF models

Off On COM N

FOR FIXED WIRING ONLY

Heating

satisfied

or call for

cooling

Not

required

Call

for

heat'

Common

/switched

live from

Time Control

FAULT DIAGNOSIS (All Models)

If the display shows E1, the following faults could have occurred

1. Internal temperature sensor has failed.

2. Ambient temperature is outside product operating temperature

range.

ºc

p I

H i

E S

E I

E 2

E L

C Y

i 0

ºc

i 5

ºc

2 4

ºc

9 0

ºc

6 0

ºc

4 0

ºc

3 0

ºc

2 0

ºc

7 0

ºc

p I

0 0

C Y

E S

E L

SET

i 5

ºc

SET

2 2

ºc

Digistat+ & Digistat+RF

Room Thermostat

Models:

30002 / RF601

Invensys Controls Europe

Technical Helpline: +44 (0) 845 130 7722

www.draytoncontrols.co.uk

Installation / User Guide 06490056001 (09/05)

Installation Guide

Technical Data

DIGISTAT+, DIGISTAT+RF

ROOM UNIT

Power Supply: 2 x AA Size, 1.5V alkaline batteries

Switch Type & Rating:

Relay version: SPDT 2(1)A 12-240V AC(DC) Volt free

Radio frequency:

RF version: 433 MHz

Radio Signal Range: 30m typically. The range may be affected by

(RF Version) the composition / density and number of

walls between the Digistat RF and SCR.

Temperature Range: 5 to 30ºC

Control Accuracy: + 0.5K @ 20ºC

Ambient Temperature: Operating 0ºC to 50ºC /

Storage –20ºC to 55ºC

Applicable Standards: EN60730-1:2001; EN60730-2-7:1992

73/23/EEC Low Voltage Directive

89/336/EEC EMC Directive

EN300220-1

Mounting: Suitable for surface or conduit box

mounting

Wiring:

Relay: Designed for ﬁxed wiring only, to comply

with current IEE regulations.

RF: No wiring required

SINGLE CHANNEL

RECEIVER (SCR)

Power Supply: 230V AC 50Hz

Switch Type & Rating: SPDT (voltage free) 2(1)A 230V AC or

23V AC (DC)

Wiring: Designed for ﬁxed wiring only, to comply

with current IEE regulations.

Reception Frequency: 433 MHz

Insert screwdriver

and unlatch

the clip

Pull back plate

straight off

When changing an existing

product and there is a

neutral wire present, use the

neutral (N) terminal on the

product.

06490056001 ISS E.indd 1 20/9/06 10:59:40

Produkt Specifikationer

Mærke:	Drayton Erie
Kategori:	Termostat
Model:	Digistat +

Har du brug for hjælp?

Hvis du har brug for hjælp til Drayton Erie Digistat + stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Drayton Erie Manualer

Drayton Erie Digistat 3 Manual

25 August 2024

Drayton Erie Digistat + Manual

24 August 2024

Drayton Erie Digistat +3 Manual

24 August 2024

Drayton Erie Digistat 2 Manual

24 August 2024

Drayton Erie Digistat RF2 Manual

23 August 2024

Termostat Manualer

Nyeste Termostat Manualer

ATTACK OT80 Manual

17 December 2024

Warmup +Kit Manual

17 December 2024

Warmup 5iE Manual

17 December 2024

Tru Components TX4S-14R Manual

17 December 2024

EQ-3 CC-RT-O-CnL-W-R5-2 Manual

16 December 2024

EQ-3 HmIP-WTH-2 Manual

16 December 2024

EQ-3 HMIP-WTH Manual

16 December 2024

EQ-3 HMIP-eTRV Manual

16 December 2024

EQ-3 HM-TC-IT-WM-W-EU Manual

16 December 2024

EQ-3 HM-CC-RT-DN Manual

16 December 2024