Drayton Digistat+1 Manual

Drayton Termostater Digistat+1

Læs gratis den danske manual til Drayton Digistat+1 (4 sider) i kategorien Termostater. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Drayton Digistat+1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

50 mm

minimum

clearance

40 mm

minimum

clearance

40 mm

N L 1 2 3 4

clearance

70 mm

minimum

clearance

N L 1 2 3

230V a.c.

Fused 3A

Common

Heating

satised

or call for

cooling

Call for

heat

Volt free contacts

Room Thermostat

Models:

RF710/22190/2219

If you do not have the knowledge to install the SCR safely then you

must arrange for a competent electrician to install it for you. Wiring

must conform to the current IEE wiring regulations.

Prior to commencing the installation you must ensure the mains

supply is switched o.

The system wiring must be able to be fully disconnected from the

mains supply by a switch incorporated in the ﬁxed wiring having a

contact separation of at least 3mm on both poles. Fused at 3A.

The Digistat SCR (receiver) should be mounted in a convenient

position, close to the boiler or central heating system wiring centre.

(Care should be taken not to mount the SCR in a position where it

is surrounded by metal objects or mains voltage cable, as this may

interfere with the radio signal).

For the best performance install in an open space, at least 30cm

distance from any metal objects including wall boxes and boiler

housing.

It is recommended that the SCR is mounted on the wall nearest the

ﬁnal location of the Digistat +RF room thermostat and not less than

30cm from the boiler side panel.

mounting single conduit box using M3.5 x 14 screws. Minimum

wallplate clearances are shown.

1. Loosen the securing screws, remove the wallplate, and if surface

wiring is to be used, snap out the cable entry strip on the bottom

edge of the wallplate with a pair of pliers.

2. Fix the wallplate, terminals at the top, either direct onto the ﬂat

wall using wall plugs and no 6 x1” wood screws or on a ﬂush

3. Complete the wiring to the SCR wallplate in accordance with the

relevant diagram, to comply with current IEE wiring regulations.

4. Place the SCR onto the wallplate and tighten the securing screws.

This product is double insulated and does not require an earth connection.

The SCR should be wired to the combi boiler or central heating wiring using

the correct type of cable or ﬂex. The SCR should be wired in to replace

hard wired room or programmable thermostats shown on the system or

boiler wiring diagrams. Always check other manufacturers instructions for

compatibility.

BOILER

30cm Min

Preferred side of boiler

The range may be aected by

composition/density and number of walls

between the Digistat +RF and SCR

Radio Signal Range:

30m Typically

SCR

Override

Receive / Alarm

Learn

Mode

Digistat

SCR

Wireless System

Digistat

1 &

Digistat

1RF

Drayton Controls reserve the right

to make changes without notice

and cannot accept liability for errors.

06515065001 ISS G

Room Thermostat

User Guide

Models:

RF710/22190/2219

also come on. Check to see if the boiler and/or motorised valve

are working.

Standard for all models

IMPORTANT: MULTIZONE INSTALLATIONS ONLY

If more than one ‘wireless system’ is ﬁtted within the same property.

ie. for controlling 2 or more zones (multi-zone) it is essential that the

Digistat RF units are matched correctly to the relevant SCR. This is easily

achieved by commissioning each Digistat and SCR in turn.

1. Install (see installation instructions) and turn power on to the

SCR (receiver). If a separate programmer is ﬁtted, ensure that it is

switched on. The red LED should come on.

2. Push the ‘override’ button on the SCR once. The green LED should

than one metre).

3. To enter ‘learn’ mode push the button marked 1 followed by 2

(OVERRIDE) and hold both depressed together. The red LED

ni si RCS eht gniyfingis tuo og neht dna sdnoces 2 rof hsaﬂ dluohs

.snottub htob esaeleR .edom nrael

4. The red and green LED’s should both now be on.

5. Take the Digistat RF and hold it within sight of the SCR (no closer

11.

12.

The red LED on the SCR should ﬂash for 7 seconds. This conﬁrms

that the radio signal is being sent and received. After 7 seconds the

red LED should go out and the green one come on.

Check to conﬁrm that the boiler and/or motorised valves are

working.

6. Remove the battery cover and ﬁt the batteries.

7. The Digistat RF should now display the actual room temperature.

If the unit has been stored in a cold place, it may take time to warm

up.

8. As soon as the batteries are ﬁtted, the red LED on the SCR should

ﬂash for 7 seconds and then go out.

erutarepmet moor eht no gnidneped ffo ro no eb yam DEL neerg ehT

at the time of commissioning.

9. If the red LED remains on, remove the batteries on the Digistat RF,

check the battery positions are correct, and once the display has

faded, repeat steps 6 to 8.

10. Increase the ‘SET’ temperature on the Digistat RF by pressing the

+ button until a ﬂame symbol appears, in the left hand segment of

the display.

During normal operation the red LED on the SCR will ﬂash for 7 seconds

each time a radio signal is received from the Digistat RF. This will occur

approximately every 5 minutes.

The green LED on the SCR denotes a call for heat (ON).

13. Decrease the ‘SET’ temperature on the Digistat RF by pressing the

- button until the ﬂame symbol disappears.

14. The red LED on the SCR should ﬂash for 7 seconds. After 7 seconds

both the red and green LEDs should go out. Check that the boiler

and/or motorised valve have powered down.

15. Place the Digistat RF in the chosen operating position, (see Digistat

RF location section) and repeat steps 10 to 14. Once you have

conﬁrmed the sy stem oper ates correctly, ﬁ t and secure the Digistat RF

to the wall (see installation instructions).

L N 1 2 3

L -

SCR

N -

Digistat + RF

Radio signals

to SCR - no wiring

Switched

230 a.c.V

fused 3A,

Internal

boiler

electro cs ni

External

controls

connections

L N 1 2 3

SCR

Switched live

from wiring

Motorised valve

centre

and/or

To boiler

pump

Radio signals

to SCR - no wiring

230V a.c.

Digistat + RF

fused A 3

Dig tat is

1RF

Digistat

1RF

and cannot accept liability for errors.

Drayton Controls reserve the right

to make changes without notice

Digistat

1 &

Digistat

1RF

What is a room thermostat?

... An explanation for householders

A roo th mostat simply sw ches the hea nm er it ti g system on

an o as necessary. It works by sensind  g th air temperature, e

switchin on the heatin when thg g e ai temperature falls below r

the thermostat setting, an s tchind wi g  s it o once thi set

temperature ha been reached. s

Turning a roo thermostat to a highe settin wil no m e m r g l t ak

the roo heat up an faster. Ho quickly th oo he s up m y w e r m at

depends on the design of th heatin sy em fo example, the e g st , r

size of boile an radiators.r d

Neither does th settin aect hoe g w quickly th oo cools e r m

down. Turning a roo thermostat to a lowem r set ng wil esult ti l r

in th oo bein cone r m g

trolled at a lower temperature an saves , d

en y.erg

Th heatin system will not work if a time s tc o pro ammer e g wi h r gr

ha switched it o.s

Th wa to set an us your roo th mostae y d e m er t is to ﬁn he d t

lowest temperat e settin that yo are comfo able with, ur g u rt

an then leave i alone to do its job. Th be wa o do this d t e st y t

i to set th roo thermostat to a los e m w temperat e – sa 18ºC ur y

– and the turn t up by one de ee each da until yo aren i gr y u

comfortable with the temperat e. You won’ have to adjus theur t t

thermostat fu her. Any adjustment above th s tin will wastert is et g

en y an cost yo m e money.erg d u or

I yo heating system is a boiler wf ur

ith adiators, there w l r il

usually be only on oo th mostat to co ole r m er ntr the whole

house. But yo ca hav diere temperat es in individual u n e nt ur

rooms b installing thermostatic radiat va es (TRVs) on y or lv

individual a at s. f you don’t hav TRVs yo should choose r di or I e , u

a temperat e that is easonable four r r th whole house. If yo do e u

hav TRVs, yo can choose a sl htly h he setting to make sure e u ig ig r

that even th coldest oo is comfortable, the prevent any e r m n

o rheating in other rooms by adjusting th TRVs.ve e

Roo thermostats need a fre ﬂo of air to sense he m e w t

temperature so they mus no be cov ed by cu ains or , t t er rt

blocked by furn

iture. Nearby electric ﬁres televisions wall or , ,

table lamps may prevent th thermosta from w n properly.e t orki g

06515065001 ISS G

Produkt Specifikationer

Mærke:	Drayton
Kategori:	Termostater
Model:	Digistat+1

Har du brug for hjælp?

Hvis du har brug for hjælp til Drayton Digistat+1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostater Drayton Manualer

Drayton Digistat+3 Manual

15 Januar 2025

Drayton Digistat+1 Manual

8 Oktober 2024

Termostater Manualer

Nyeste Termostater Manualer

Grässlin Famoso 555 Manual

15 Januar 2025

Emerson 1F83C-11PR Manual

14 Januar 2025

Heatmiser PRT Manual

13 Januar 2025

Emerson 1F85U-42NP Manual

13 Januar 2025

Fantini Cosmi CH116 Manual

12 Januar 2025

Watts BT 050 Chrono Battery Manual

15 Oktober 2024

Siemens RDH10RF Manual

14 Oktober 2024

Heatmiser Touch-N Manual

13 Oktober 2024

Heatmiser PRT-TS Manual

10 Oktober 2024

Xavax 00111971 Manual

10 Oktober 2024