DSC PG9949 Manual

DSC Fjernudløser PG9949

Læs nedenfor 📖 manual på dansk for DSC PG9949 (14 sider) i kategorien Fjernudløser. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/14

PG9949/PG8949/PG4949

PowerG 2-Button Wireless Key Installation

Instructions

WARNING!

Choking Hazard; Small parts; The pendant and belt

clip are NOT for children under 3 years

Do not submerge the wireless key in any liquid as it

will damage the electronic circuits. Keep this manual for future

reference.

Operation

The PGx949 is a programmable 2-button wireless key. The

PGx949 can be configured to transmit up to three separate com-

mands to the alarm system. Two of the commands are transmit-

ted by pressing one of the buttons separately, and the third is by

pressing them simultaneously. Confirmation of a successful

transmission is indicated by the LED light.

Default Settings

Arm {button 1) - Press for 1 second

Disarm (button 3) - Press for 1 second.

Panic (button 4) - Press and hold both buttons for more than 3

seconds.

Device Setup

Enrollment

To quick enroll:

1. On a keypad press [*] [8] [Installer Code]

[804] [000].

2. Press and hold the [ ] button on the wire-

less key until the LED lights steady and then release the

[ ] button while the LED is still lit and a confirmation

message appears on the keypad.

3. Press [*] on the keypad to confirm the device ID.

4. Enter [3 digit wireless key #]

5. Assign the wireless key to a partition by entering the [three

digit partition #].

6. To assign the wireless key to a user enter the [3 digit user #].

To pre-enroll:

1. Remotely configure the unique ID number into the system.

For more information see the HSM2HOST manual.

2. When on-site, press the button on the wireless key.

Programming Buttons

The buttons are programmable.

To change button programming:

1. From a keypad enter [*] [8] [Installer Code] [804][601] to

[632].

2. Configure button 1 (default arm) using the table below.

Enter the desired two digit option.

3. Configure button 3 (default disarm) by entering the desired

two digit option.

4. Configure button 4 (both buttons pressed simultaneously) by

entering the desired two digit option.

Configuration

To enter the wireless configuration section enter [804][601].

Device Toggles

Assembly

Attaching to a Belt Clip

1. Slide the device into the holder until you feel it snap

securely inside.

2. To attach the belt clip, slide it onto the rails on the rear of the

holder.

Mounting

1. Align the holder on a wall facing up as illustrated.

2. Using two #4 5/8” screws and

appropriate wall anchors, secure

the holder to the wall

3. Slide the device into the holder

until you feel it snap securely

inside.

Maintenance

Warning! Modifications to this wire-

less key not expressly approved by the

party responsible for compliance may

void the user’s authority to operate it.

Replacing the Battery

The required battery is CR2032 Lithium 3V, manufactured by

VARTA or Energizer, purchased from a DSC-approved sup-

plier.

When this wireless key is out of use, remove all batteries and

dispose of them separately. Bring electrical appliances to the

local collecting points for waste electrical and electronic equip-

ment. Batteries are harmful to the environment, please help to

protect the environment from health risks.

Replace the battery at least once every 5 years, or upon observ-

ing that the LED flickers when transmitting.

NOTE: The polarity of the battery must be observed. Improper

handling of lithium batteries may result in heat generation,

explosion or fire, which may lead to personal injuries.

WARNING: Danger of explosion if batteries are installed

incorrectly. Replace only with the same or equivalent type rec-

ommended by the manufacturer. Keep away from small chil-

dren. If batteries are swallowed, promptly see a doctor. Do not

try to recharge these batteries. Disposal of used batteries must

be made in accordance with the waste recovery and recycling

regulations in your area.

1. To replace the battery, insert a coin into the slot on the bot-

tom of the unit and twist it open.

Note: Make sure the elastic pad within the cover remains in

place. Put it back in place if it falls off.

2. Extract the old battery from its holder, and replace it with a

recommended new battery. Ensure that the plus side of the

battery faces up, attaining correct polarity.

3. Test the device by pressing the button. The LED indicator

should light.

4. Reattach the cover securely, verifying that the cover snaps

shut.

Cleaning

The use of abrasives of any kind and solvents such as ker-

osene, acetone or thinner is strictly forbidden.

Clean the wireless key only with a soft cloth or sponge moist-

ened lightly with a mixture of water and mild detergent, and

wipe it dry immediately.

Testing

Always test the system at least once per a year.

1. Ensure the device is enrolled in the system.

2. Stand 3 m (10 ft) away from the control panel and press the

button. Verify that the transmit LED lights and the control

panel responds as programmed.

3. Operate the pendant from various locations within the area

covered by the receiver to determine "dead" locations,

where transmission is blocked by walls and large objects, or

affected by structural materials.

Note: If dead/marginal zones are a problem, relocating the

receiver may improve the performance.

Specifications

Frequency Band (MHz): CE Listed PG4949: 433-434MHz;

CE/EN listed PG8949: 868MHz; FCC/IC/UL/ULC listed

PG9949: 912-919MHz

Communication Protocol: PowerG

Battery type: For UL/ULC listed installation use only Varta or

Energizer 3V CR-2032 Lithium battery consumer grade

Battery Life Expectancy: 5 years (not verified by UL/ULC)

Low Battery Threshold: 2.05 V

Note: If transmission is still possible despite the battery condi-

tion, the unit will send a low battery signal to the control panel.

Temperature Range: -10°C to +55°C (UL/ULC only verified

the range 0ºC-49ºC)

Humidity: up to max. 93%RH, non-condensing

Dimensions (LxWxD): 53 x 33 x 11 mm (2.1 x 1.3 x 0.43 in)

Weight: 15 g (0.5 oz)

Weight (including battery): 20 g (0.7 oz)

Note: To be used in non-hazardous locations only.

Compatible Receivers

433MHz Band: HSM2HOST4; HS2LCDRF(P)4;HS2IC-

NRF(P)4; PG4920

868MHz Band: HSM2HOST8; HS2LCDRF(P)8; HS2IC-

NRF(P)8;PG8920

912-919MHz Band: HSM2HOST9; HS2LCDRF(P)9; HS2IC-

NRF(P)9; PG9920

Note: Only devices operating in band 912-919MHz are UL/

ULC listed.

UL/ULC Notes

Only model PG9949 operating in the frequency band 912-

919MHz is UL/ULC listed. The PG9949 has been listed by UL

for commercial and residential burglary applications and by

ULC for residential burglary applications in accordance with

the requirements in the Standards UL1610/UL1023/ULC-

ORD-C1023 and ANSI/SIA CP-01-2010 Control Panel

Standard – Features for False Alarm Reduction.

Note: For UL commercial burglary applications:

• After arming the system via the wireless key the user should verify the

closing confirmation has been indicated at the keypad.

• Panic button must be disabled.

For UL/ULC installations use these device only in conjunction

with compatible DSC wireless receivers: HSM2HOST9,

HS2LCDRF(P)9, HS2ICNRF(P)9 and PG9920. After

installation verify the product functionality in conjunction with

the compatible receiver used.

Europe: The PG4949 and PG8949 are compliant

with the RTTE requirements - Directive 1999/5/EC

of the European Parliament and of the Council of 9

March 1999. The PG8949 is certified by Applica

Test and Certification to the following standards: EN50131-3,

EN50131-1 GRADE 2, CLASS II, EN50131-6 Type C.

Applica Test and Certification has certified only the 868 MHz

variant of this product. According to EN 50131-1:2006 and

A1:2009, this equipment can be applied in installed systems up

to and including Security Grade 2, Environmental Class II. UK:

The PG8949 is suitable for use in systems installed to conform

to PD6662:2010 at Grade 2 and environmental class 2 BS8243.

The Power G peripheral devices have two- way communication

functionality, providing additional benefits as described in the

technical brochure. This functionality has not been tested to

comply with the respective technical requirements and should

therefore be considered outside the scope of the product’s certi-

fication

FCC COMPLIANCE STATEMENT

WARNING! Changes or modifications to this unit not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in residential installations.

This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio and tele-

vision reception.

However, there is no guarantee that interference will not occur

in a particular installation. If this device does cause such inter-

ference, which can be verified by turning the device off and on,

the user is encouraged to eliminate the interference by one or

more of the following measures:

– Re-orient or re-locate the receiving antenna.

– Increase the distance between the device and the receiver.

– Connect the device to an outlet on a circuit different from the

one that supplies power to the receiver.

– Consult the dealer or an experienced radio/TV technician.

This equipment complies with FCC and IC RF radiation expo-

sure limits set forth for an uncontrolled environment.

This device complies with FCC Rules Part 15 and with Industry

Canada licence-exempt RSS standard(s). Operation is subject

to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any inter-

ference that may be received or that may cause undesired oper-

ation.

Le present appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence. L'exploita-

tion est autorisee aux deux conditions suivantes :(1) l'appareil

ne doit pas produire de brouillage, et (2) l'utilisateur de l'appar-

eil doit accepter tout brouillage radioelectrique subi, meme si le

brouillage est susceptible d'en compromettre le fonctionne-

ment.

PG9949/PG8949/PG4949

Instructions d'installation de la clé sans fil

à 2 boutons PowerG

AVERTISSEMENT !

Risque d'électrocution ; Pièces de faibles dimen-

sions ; La clé sans fil et l'attache de ceinture NE

conviennent PAS à des enfants de moins de 3 ans.

Ne pas plonger la clé sans fil dans aucun liquide car les circuits

électroniques risquent de s'endommager. Conserver ce manuel

pour une consultation future.

Fonctionnement

La clé PGx949 est une clé sans fil à 2 boutons programmables.

Elle est configurable pour transmettre jusqu'à trois commandes

séparées au système d'alarme. Deux des commandes sont trans-

mises en appuyant séparément sur l'un des boutons, et la

troisième est transmise en y appuyant simultanément. La con-

firmation d'une transmission établie avec succès est signalée

par le voyant lumineux.

Réglages par défaut

Armement (bouton 1) : Appuyez sur pendant 1 sec-

onde

Désarmement (bouton 3) : Appuyez sur pendant 1 sec-

onde

Demande d'aide (bouton 4) : Appuyez de façon prolongée les

deux boutons pendant plus de 3 secondes.

Réglage du dispositif

Attribution

Pour une attribution rapide :

1. Sur un clavier, appuyez sur [*] [8] [Code de

l'installateur] [804] [000].

2. Appuyez et maintenez la touche sur la clé sans fil

jusqu'à ce que la LED s'allume stable et puis relâchez le bou-

ton [ ] pendant que le voyant est toujours allumé et un

message de confirmation apparaît sur le clavier.

3. Appuyez sur [*] sur le clavier pour confirmer l'ID de l'appa-

reil.

4. Entrez [3 chiffres sans clé #]

5. Attribuez la clé sans fil à une partition en entrant le [trois

chiffres partition #].

6. Pour attribuer la clé sans fil à un utilisateur d'entrer le [3

chiffres utilisateur #].

Pour une attribution préalable :

1. Configurez à distance le numéro ID unique dans le système.

Pour plus d'informations, consultez le manuel HSM2HOST.

2. Sur site, appuyez sur le bouton [*] de la clé sans fil.

Boutons de programmation

Les boutons sont programmables.

Pour changer la programmation des boutons :

1. Depuis le pavé numérique, entrez la commande [*] [8]

[Code de l'installateur] [804][601] à [632].

2. Configurez le bouton 1 (armement par défaut) en utilisant le

tableau ci-dessous. Entrez l'option à deux chiffres souhaitée.

3. Configurez le bouton 3 (désarmement par défaut) en entrant

les deux chiffres de l'option souhaitée.

4. Configurez le bouton 4 (les deux boutons appuyés simul-

tanément) en entrant les deux chiffres de l'option souhaitée.

Configuration

Pour accéder à la section de configuration sans fil, entrez la

commande [804][601].

Commutateurs du dispositif

Assemblage

Fixation de l'attache de ceinture

1. Faites glisser le dispositif dans l'étui jusqu'à ce qu'il

s'enclenche solidement à l'intérieur.

2. Pour fixer l'attache de ceinture, faites-la glisser dans les rails

sur l'arrière de l'étui.

Fixation

1. Alignez le support sur le mur, vers le haut comme illustré.

00 Disabled 16 Quick Exit

01 Disarm 17 Arm Interior

02 Instant Stay Arm 21 Comm. Output 1

03 Stay Arm 22 Comm. Output 2

04 Away Arm 23 Comm. Output 3

05 [*][9] No Entry 24 Comm. Output 4

06 Chime On/Off 29 Bypass Group Recall

07 System Test 33 Bypass Recall

09 Night Arm 51 Aux. Alarm

12 Global Stay Arm 52 Panic

13 Global Away Arm

14 Global Disarm

[011][01] Supervision - Default [N]

Enables supervision of the device.

00 Désactivé 16 Sortie rapide

01 Désarmer 17 Armement en intérieur

02 Armer en mode à

domicile à effet

instantané

21 Communication Sortie 1

03 Armer en mode à

domicile

22 Communication Sortie 2

04 Armer en mode

d'absence

23 Communication Sortie 3

05 [*][9] Sans entrée 24 Communication Sortie 4

06 Carillon Activé/

Désactivé

29 Rappel de groupe de

suspension

07 Essai du système 33 Rappel de suspension

09 Armer en mode nuit 51 Alarme Alarme

12 Armer globalement en

mode à domicile

52 De demande d'aide

13 Armer globalement en

mode absence

14 Désarmer globalement

[011][01] Supervision : Valeur par défaut [O]

Active la supervision

D-305049

Produkt Specifikationer

Mærke:	DSC
Kategori:	Fjernudløser
Model:	PG9949

Har du brug for hjælp?

Hvis du har brug for hjælp til DSC PG9949 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernudløser DSC Manualer

DSC PG9949 Manual

20 August 2024

DSC WT4989 Manual

5 August 2024

DSC PG9938 Manual

23 Juli 2024

Fjernudløser Manualer

Nyeste Fjernudløser Manualer

Vimar 16622 Manual

15 December 2024

Vimar ELVOX EDS3 Manual

15 December 2024

Vimar 20173.B Manual

15 December 2024

Protector AS-5030 Manual

11 December 2024

Angler RC-16-T Manual

10 December 2024

Angler RC-16-R Manual

10 December 2024

Vello FreeWave Flash Trigger LR Manual

1 Oktober 2024

Vello FreeWave Fusion Basic 2.4 GHz Manual

1 Oktober 2024

Vello FB-TTL-C Manual

30 September 2024

Vello FWIRC-C Manual

30 September 2024