ECS P55H-A SLI Manual
Læs nedenfor 📖 manual på dansk for ECS P55H-A SLI (90 sider) i kategorien Bundkort. Denne guide var nyttig for 15 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/90
Preface
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufac-
turer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective
owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits governing
this device. Changes or modifications not expressly approved by the system’s manu-
facturer could void the user’s authority to operate the equipment.
ii
Preface
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interfer-
ence that may cause undesired operation
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interference-
causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur
le matériel brouilieur du Canada.
About the Manual
The manual consists of the following:
Describes features of the
motherboard.
Go to Hpage 1
Describes installation of
motherboard components.
Go to H
Provides information on using
the BIOS Setup Utility.
Go to Hpage 27
Go to H
Describes the ATI CrossfireTM
Technology
page 49
Describes the motherboard soft-
wa re
Go to Hpage 53
Chapter 2
Chapter 1
Introducing the Motherboard
Chapter 3
Using BIOS
Chapter 4
Using the Motherboard Software
Chapter 5
ATI CrossfireTM Technology Support
Describes the Intel® Matrix Stor-
age Manager RAID Configura-
tions
Chapter 6
Intel® Matrix Storage Manager
RAID Configurations Go to Hpage 57
Chapter 8
Setting Up eJIFFY
Describes the eJIFFY setting
up
Go to H page 69
page 7
Installing the Motherboard
chapter 9
Provides basic trouble shooting
Trouble Shooting tips H page 79
Go to
Chapter 7
NVIDIA®®®®® Hybrid SLI®®®®® Technology Sup-
port
Provides information about SATA
RAID Setup
Go to page 63
H
iii
Chapter 2 7 7 7 7 7
Installing the Motherboard 7
Safety Precautions...........................................................................7
Choosing a Computer Case............................................................7
Installing the Motherboard in a Case...........................................7
Checking Jumper Settings..............................................................8
Setting Jumpers.......................................................................8
Checking Jumper Settings.......................................................9
Jumper Settings.......................................................................9
Installing Hardware...................................................................10
Installing the Processor.........................................................10
Installing Memory Modules...................................................12
Expansion Slots......................................................................16
Connecting Optional Devices.................................................18
Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive...21
Connecting I/O Devices.................................................................22
Connecting Case Components.....................................................23
Front Panel Header...............................................................26
TT
TTTABLE OF CONTENTSABLE OF CONTENTS
ABLE OF CONTENTSABLE OF CONTENTSABLE OF CONTENTS
Preface i
Chapter 1 1
Introducing the Motherboard 1
Introduction....................................................................................1
Feature.............................................................................................2
Specifications..................................................................................5
Motherboard Components............................................................6
Chapter 3 27
Using BIOS 27
About the Setup Utility........................ ......................................... 27
The Standard Configuration...................................................27
Entering the Setup Utility........................................................27
Resetting the Default CMOS Values.....................................28
Using BIOS......................................................................................29
Standard CMOS Setup..........................................................30
Advanced Setup.....................................................................32
Advanced Chipset Setup.........................................................34
Integrated Peripherals...........................................................34
Power Management Setup.....................................................36
PCI/PnP Setup.......................................................................37
iv
PC Health Status...................................................................38
M.I.B (MB Intelligent BIOS II )........................................42.III I
Load Default Settings............................................................45
Supervisor Password............................................................45
User Password......................................................................46
Save & Exit Setup...................................................................46
Exit Without Saving.................................................................46
Updating the BIOS..................................................................47
Chapter 4 49 49
49 49
49
Using the Motherboard Software 49
About the Software DVD-ROM/CD-ROM..................................49
Auto-installing under Windows XP/Vista/7...............................49
Running Setup..........................................................................50
Manual Installation........................................................................52
Utility Software Reference........................................................52
Chapter 5 53 53 53 53 53
ATI CrossFireTM Technology Support 53
Requirements..................................................................................53
Installing CrossFireTM graphics cards.........................................53
The CatalystTM Control Center Dialog Box.................................55
View...........................................................................................55
To Enable CrossFireTM..............................................................55
Chapter 6 57 57
57 57
57
Intel®
Matrix Storage Manager RAID Configurations 57
Before creating a RAID set...........................................................57
Entering Intel® Matrix Storage Manager RAID BIOS utility....58
Creating a RAID set.......................................................................60
Deleting a RAID set.......................................................................61
Resetting disks to Non-RAID......................................................62
Exiting Setup...................................................................................62
Chapter 7 63 63 63 63 63
NVIDIAÒ Hybrid SLIÒ Technology Support 63
Key Features..................................................................................63
Hybrid SLI Products.....................................................................64
Hybrid Requirements and Constraints......................................65
Installation and Use.......................................................................66
v
Chapter 9 79 79
79 79
79
Trouble Shooting 79
Start up problems during assembly...................................................79
Start up problems after prolong use.................................................80
Maintenance and care tips.................................................................80
Basic Troubleshooting Flowchart....................................................81
POST Code Checkpoints 8383
838383
Chapter 8 69 69 69 69 69
Setting Up eJIFFY 69
Introduction....................................................................................69
Installation and BIOS Setup.........................................................70
Entering eJIFFY......................................................................................73
Features Icons.........................................................................................74
Usage FAQ..............................................................................................75
vi
Memo
1
Introducing the Motherboard
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the P55H-A SLI motherboard. This motherboard is a high
performance, enhanced function motherboard designed to support the LGA1156
socket for Intel® LGA1156 Core i7/i5/i3/Pentium processor for high-end business or
personal desktop markets.
This motherboard is based on Intel® P55 Express Chipset for best desktop platform
solution. P55 is a single-chip, highly integrated, high performance Hyper-Threading
peripheral controller, unmatched by any other single chip-device controller. This
motherboard supports up to 16 GB of system memory with dual channel DDR3
1333/1066 MHz. Two PCI slots are supported, fully compliant with PCI rev 2.3
specification at 33MHz. High resolution graphics via two PCI Express slots, in-
tended for Graphics Interface, is fully compliant to the PCI Express Base Specifica-
tion revision 2.0. Additionally, one PCI Express p7-x4 slot is supported, fully compliant
to the PCI Express Base Specificaiton. It implements an EHCI compliant interface
that provides fourteen USB 2.0 ports (eight USB ports and three USB 2.0 headers
support additional six USB ports). It supports the ATI CrossFire
TM Technology and
NVIDIA SLI that allows you to install two GPU graphics cards. It also supports Intel®
Matrix Storage Technology, providing both AHCI and RAID 0, 1, 5 and 10 configu-
ration.
The motherboard is equipped with advanced full set of I/O ports in the rear panel,
including PS/2 mouse and keyboard connectors, one CLR_CMOS button, one eSATA
ports, one LAN port, eight USB ports, one optical SPDIFO port and audio jacks for
microphone, line-in and 8-ch line-out.
In addition, this motherboard comes with an LED for debug, a power on button and
a reset button. The processor can be overclocked when CPU Over-clocking Func. is
set to Enabled in M.I.B.III (MB Intelligent BIOS III).
2
Introducing the Motherboard
Feature
• Accommodates Intel® LGA1156 Core i7/i5/i3/Pentium processor
• Supports “Hyper-Threading” technology CPU
“Hyper-Threading” technology enables the operating system into thinking
it’s hooked up to two processors, allowing two threads to be run in parallel, both
on separate “logical” processors within the same physical processor.
The motherboard uses an LGA1156 type of socket that carries the following
features:
Processor
The Intel P55 Express Chipset is a single-chip with proven reliability and per-
formance.
Chipset
• Supports DDR3 1333/1066 DDR3 SDRAM with Dual-channel architec-
ture
• Accommodates four unbuffered DIMMs
• Up to 4 GB per DIMM with maximum memory size up to 16 GB
• Supports 1 Gb, 2 Gb and 4 Gb DDR3 DRAM technologies for p8-x8 and x16
devices (It is not recommended to use 512 Mb DDR3 memory device on
this motherboard)
Memory
• Support Intel® Matrix Storage Technology, providing both AHCI and RAID
0, 1, 5 and 10 configuration.
• Two x16 PCI Express Gen2 ports each supporting up to 8 GB/s direc-
tion peak bandwidth
• An additional p8-x4 PCI Express Gen1 port configuration to 2 p8-x2 interface
• Compliant with PCI Rev 2.3 interface at 33 MHz
• Integrated SATA 3.0 Gb/s Host Controller
• Fourteen USB 2.0 ports supported
• Serial Peripheral Interface (SPI) support
• Enhanced DMA Controller, interrupt controller, and timer functions
Audio
• 7.1 + 2 channel High Definition Audio Codec
• All DACs Support 192k/96k/48k/44.1kHz DAC sample rate
• High –quality analog differential CD input
• Meets Microsoft WHQL/WLP 3.0 audio requirements
• Direct Sound 3DTM compatible
Onboard LAN
• Supports PCI ExpressTM 1.1
• Integrated 10/100/1000 transceiver
• Wake-on-LAN and remote wake-up support
4
Introducing the Motherboard
Special Features
Intelligent Power Saving (IPS)
Equipped with IPS indicator to indicate advanced
power system that provides better energy ef-
ficiency for Intel® processors. The energy can
be greatly saved during idle operation or other
low load conditions which can be confirmed
through IPS indicator.
4E Innovation
4E innovation representing “Easy Attach”,
“Easy Button” “”Easy Clear” and “Easy
Debug”, P55H-A SLI provides great conve-
nience for system installation and performance
tweaking that meets the demand from hard-
ware extremists.
6
Introducing the Motherboard
Motherboard Components
Table of Motherboard Components
LABEL COMPONENTS
1. CPU Socket LGA1156 socket for Intel® LGA1156 Core
i7/i5/i3/Pentium processor
2. CPU_FAN CPU cooling fan connector
3. DDR3_1~4 240-pin DDR3 SDRAM slots
4. CASE_FAN Case cooling fan connector
5. ATX_POWER Standard 24-pin ATX power connector
6. SYS_FAN System cooling fan connector
7. CLR_CMOS Clear CMOS jumper
8. SATA1~6 Serial ATA connectors
9. PWR_BTN Power on button
10. RST_BTN Reset button
11. F_PANEL Front panel switch/LED header
12. F_USB1~3 Front panel USB headers
13. IDE Primary IDE connector
14. COM Onboard serial port header
15. SPDIFO SPDIF out header
16. CD_IN Analog audio input connector
17. F_AUDIO Front panel audio header
18. PCI1~2 32-bit add-on card slot
19. PCIE16X_1~2 PCI Express slots for graphics interface
20. PCIE4X1 PCI Express p12-x4 slot
21. PCIE1 PCI Express p12-x1 slot
22. ATX4P Auxiliary power connector for graphics card
23. PWR_FAN Power cooling fan connector
24. ATX12V 8-pin +12V power connector
This concludes Chapter 1. The next chapter explains how to install the motherboard.
7
Installing the Motherboard
Chapter 2
Installing the Motherboard
Safety Precautions
• Follow these safety precautions when installing the motherboard
• Wear a grounding strap attached to a grounded device to avoid dam-
age from static electricity
• Discharge static electricity by touching the metal case of a safely
grounded object before working on the motherboard
• Leave components in the static-proof bags they came in
• Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case
There are many types of computer cases on the market. The motherboard complies
with the specifications for the ATX system case. Some features on the motherboard
are implemented by cabling connectors on the motherboard to indicators and switches
on the system case. Make sure that your case supports all the features required.
Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O
template in the case matches the I/O ports installed on the rear edge of the
motherboard.
This motherboard carries an ATX form factor of 305 x 244 mm. Choose a case that
accommodates this form factor.
Installing the Motherboard in a Case
Refer to the following illustration and instructions for installing the motherboard in
a case.
Most system cases have mounting brackets installed in the case, which correspond
the holes in the motherboard. Place the motherboard over the mounting brackets
and secure the motherboard onto the mounting brackets with screws.
Ensure that your case has an I/O template that supports the I/O ports and expansion
slots on your motherboard.
Produkt Specifikationer
| Mærke: | ECS |
| Kategori: | Bundkort |
| Model: | P55H-A SLI |
Har du brug for hjælp?
Hvis du har brug for hjælp til ECS P55H-A SLI stil et spørgsmål nedenfor, og andre brugere vil svare dig
Bundkort ECS Manualer
12 Januar 2025
12 Januar 2025
12 Januar 2025
12 Januar 2025
11 Januar 2025
11 Januar 2025
16 November 2024
18 August 2024
17 August 2024
17 August 2024
Bundkort Manualer
- Bundkort Asus
- Bundkort Gigabyte
- Bundkort Asrock
- Bundkort MSI
- Bundkort NZXT
- Bundkort Sapphire
- Bundkort Intel
- Bundkort Sharkoon
- Bundkort Supermicro
- Bundkort Biostar
- Bundkort Evga
- Bundkort Foxconn
- Bundkort Advantech
- Bundkort Elitegroup
- Bundkort EPoX
- Bundkort AOpen
- Bundkort Raspberry Pi
Nyeste Bundkort Manualer
27 Marts 2025
6 Marts 2025
15 Februar 2025
15 Februar 2025
15 Februar 2025
15 Februar 2025
15 Februar 2025
15 Februar 2025
15 Februar 2025
12 Februar 2025