Edision Digital Satellite Finder DSF-1 Manual

Edision Ikke kategoriseret Digital Satellite Finder DSF-1

Læs nedenfor 📖 manual på dansk for Edision Digital Satellite Finder DSF-1 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
Input frequenc y 950-2150MHz
Input level min . -40dBm
Input level max . -10dBm
Input impedanc e , r75Ohm F-connecto
Output impedance 75Ohm F-connecto , r
Power supply DC 13-18 V
Operating range
)(LNB gain 52 B60d
DIGITAL SA R TELLITE FINDE DSF-1
Owners Manua l
Overview:
The digital TFINDER is microprocesso controlled, making it very reliable and accu ate. Signal strength presented SA r r is
graphically on th LCD-display in for of thermometer-scales an in numbers (0-99) It can als present pitch tone (the higher e m d . o s
tone the ette signal on buzze di ital SATFINDE is very sensitiv and can detec the weakest signals, stron b r ) a r. The g R e t of g
incoming signals (powerful satellite, big dishe can easil be attenuated fo better readout l s ) y r .
Controls/Functions:
1. LNB Connectin Por g t
2. Receiver Connectin Por g t
3. Compass
4. Buzzer Contro Ke l y
5. LED Backligh Control Ke t y
6. TT Increasin Ke A g y
If the incomin signal is to strong, (the thermometer-scale shows max an the signal strengt value shows 99 it can easil g o s d h ) y
be attenuated enabling this attenuatio function, it reduce the incoming signa to lowe level. Ther are four ste by n” s l a r e p
attenuation totall y.
7. TT Reducin Key(The function contrary to abov item A g is e )
8. LCD Graphi Displa c y
It can displa various measured parameter for the functio you selected. has LED Backligh which user ca freely turn y s n It t n on
or turn off.
9. Adjustable knob
How to :connect
1. connect jumper cable fro the LNB the Satellit port on th digital TFINDER a m to e” e SA .
2. connect th cable from you satellite receiver the Receive port on th digital TFINDER e r to r” e SA
Operation:
1. Switch th satellite receiver on the digital TFINDER will tur on by itself e , SA n .
2. Set you dish to th proper azimuth an elevation settings.(The informatio should be supplie with your satellit dish) r e d n d e .
3. Adjus the knob unti the signal strengt display at 0%(th critical point) t l h e .
4. Peak th signal by slowl moving the azimut and elevation your dish. The higher values the better signal If the e y h of , .
digital TFINDER's reading become full scale, yo can adjust th to reduce th incoming signal lower SA s u e “ ATT” e to a
level. Continue move the dis until you hav the highest possibl meter reading an the highest possibl buzzer pitch to h e e d e .
5. Remove th jumper cable an digital TFINDER, and reconnec the LNB/LNBF your receiver e d SA t to .
IMPOR ANT NOTEST :
To a e t l R t .avoid continuous full scal reading, do no use the digita SATFINDE directly in fron of the dish
When a n , a B e e using LNB with gai higher than 60dB insert 5d attenuator between th LNB/LNBF and th digital TFINDER SA .
In case satellite receiver at hand 13-18V DC powe supply with F-connecto can be connecte on the Receive side no is a r r d r” of
the digital TFINDER to powe the TFINDER SA r SA .
Under the followin test condition:LNB gai =55dB, the carrie C/N=15dB g n r .
Insert 5d attenuator when operatin with LNB gai =6 65dB a B g n 0 ~ .
Note:all specifications cite in this leafle are subject change without notic d t to e .


Produkt Specifikationer

Mærke: Edision
Kategori: Ikke kategoriseret
Model: Digital Satellite Finder DSF-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Edision Digital Satellite Finder DSF-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Edision Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer