Electro-Voice EVF-1152S 96 Manual

Electro-Voice Højttaler EVF-1152S 96

Læs nedenfor 📖 manual på dansk for Electro-Voice EVF-1152S 96 (56 sider) i kategorien Højttaler. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/56
EVF/EVH
User Manual
EVF-1121S
EVF-1151S
EVF-1181S
EVF-2121S
EVF-2151D
EVF-1122S (All Patterns)
EVF-1122D (All Patterns)
EVF-1152S (All Patterns)
EVF-1152D (All Patterns)
EVH-1152S (All Patterns)
EVH-1152D (All Patterns)
Electro-Voice EVF/EVH User Manual
Table of Contents
Rigging-Safety Warning 3 ...........................................................................................................................................................................................
1.0 Introduction ........................................................................................................................................................................................................4
1.1 Finishes and Colors Available 9 .........................................................................................................................................................
1.2 EVF Front-Loaded Series 9 ................................................................................................................................................................
1.3 EVH Horn-Loaded Series 9 ................................................................................................................................................................
1.4 Accessories for EVF and EVH Systems .....................................................................................................................................10
2.0 Tool List ......................................................................................................................................................................................................10
3.0 Designing an EVF/EVH Cluster 11 .................................................................................................................................................................
3.1 General Aiming and Placement Guidelines 11 ..............................................................................................................................
3.2 Choosing between the EVF Full-Range and EVH Full-Range Systems 11 ............................................................................
3.21 Directivity Break Frequency Defined 11 ........................................................................................................................
3.3 More on Coverage Patterns, Multiple Coverage Patterns, the Need for Clusters of
Loudspeakers and How Far a Single Cluster Can “Reach” into a Venue 12 .........................................................................
3.31 Basic Clustering Guidelines 12 ......................................................................................................................................
3.4 Coverage-Uniformity Target 13 .........................................................................................................................................................
3.5 Multiple-Source Interference in Clusters 14 ..................................................................................................................................
3.51 Reducing Multiple-Source Interference 16 ..................................................................................................................
4.0 Preparing EVF and EVH Systems for Installation 19 ...................................................................................................................................
4.1 Recommended Preflight Procedures 19 .........................................................................................................................................
4.2 Passive/Biamp Crossover Configuration 19 ..................................................................................................................................
4.3 Rotation of High-Frequency Waveguides (EVF Systems) 20 ....................................................................................................
4.4 Rotation of High-Frequency Waveguides and Mid-Frequency Waveguide
Contours (EVH Systems) 20 ..............................................................................................................................................................
4.5 Digital Signal Processing 21 ..............................................................................................................................................................
4.51 Full-Range Systems in Passive Mode 21 .....................................................................................................................
4.52 Using the EVF-1121S and EVF-1151S Low-Frequency Systems in Full-Range
Clusters that Operate on a Single Power-Amplifier Channel 22 ............................................................................
4.53 DSP (Digital Signal Processor) Loudspeaker Presets for Biamp Operation 22 .................................................
5.0 EVF and EVH Rigging System 23 ....................................................................................................................................................................
5.1 Introduction 23 ......................................................................................................................................................................................
5.11 The Flying EV-Innovation (EV-I) Loudspeaker System 23 ........................................................................................
5.12 Important Details that Apply to the VRK and HRK Rigging Kits 26 .......................................................................
5.2 EV-I Rigging Primer 26 ........................................................................................................................................................................
5.21 Anatomy of an EVF or EVH Flying System Using M10 Eyebolts ....................................................................... 27
5.211 Eyebolt Application Warnings ................................................................................................................. 27
5.212 Eyebolt Installation 28 .....................................................................................................................................
5.213 All-Eyebolt Clusters 29 ...................................................................................................................................
5.22 VRK Kits and Vertically Rigged Clusters 31 ................................................................................................................
5.23 HRK Kits and Horizontally Rigged Clusters 32 ..........................................................................................................
5.24 Assembly Instructions for VRK and HRK Kits 35 .......................................................................................................
6.0 Rigging-Strength Ratings and Safety Factors .........................................................................................................................................37
6.1 Working Load Limit and Safety-Factor Definitions ..................................................................................................................37
6.2 Structural-Rating Overview .......................................................................................................................................................... 38
6.3 All-Eyebolt Structural Ratings ...................................................................................................................................................... 39
6.31 Working Load Limits for Eyebolts ............................................................................................................................. 40
6.32 Suspension-Line Angles 41 .............................................................................................................................................
6.33 Left-to-Right All-Eyebolt Cluster Angles 41 ................................................................................................................
6.4 VRK Rigging Structural Ratings for Vertical Clusters 42 ............................................................................................................
6.41 Working Load Limits for Eyebolts used with VRK Vertical Rigging Kits .......................................................... 44
6.42 Left-to-Right Vertical Cluster Angles 45 .......................................................................................................................
2
Electro-Voice EVF/EVH User Manual
1.0 Introduction
The Electro-Voice series is a group of compact two-way front-loaded full-range systems, available EVF
with 12- or 15-inch woofers, augmented by low-frequency and subwoofer systems. EVF full-range sys-
tems are available in two versions. The “S” versions employ 400-watt SMX low-frequency transducers
and the ND2B medium-format, 1.4-inch exit/2-inch diaphragm compression driver. The “D” versions em-
ploy 500-watt DVX-A low-frequency transducers and the DH7N large-format, 1.4-inch exit/3-inch dia-
phragm compression driver. Both compression drivers have neodymium magnetic structures. In general,
the premium components in the “D” versions provide lower distortion and reduced power compression.
The series is a group of larger two-way horn-loaded full-range systems. Both the “S” and “D” EVH EVH
versions use SMX low-frequency transducers. The “D” versions substitute the DH7N large-format com-
pression driver for the ND2B medium-format driver.
All full-range systems utilize high-order crossover networks that seamlessly integrate the low-frequency
transducers with the high-frequency compression drivers, providing very low distortion and excellent fre-
quency response.
The EVF/EVH systems have many threaded rigging points that can be used with the supplied eyebolt kits
or optional suspension kits to easily create a number of horizontal or vertical cluster configurations. All
enclosures in their normal orientations (long axis vertical) share the same height, just over 30 inches (762
mm), promoting attractive clusters. Six coverage patterns, all rotatable, are available in each family, as
shown in Table 1a. The EVF-1121S and EVF-1151S low-frequency systems have integral low-pass filters
that allow paralleling them with up to two full-range systems, offering a cost-effective way to augment the
low-frequency output of EVF full-range systems.
4
The model number scheme denotes the number of woofers, the diameter of the woofers, the number of
band passes in the system, the woofer series used and, following a forward slash, the coverage pattern.
An example is the EVF-1122S/96, which has a single SMX series 12-inch woofer in a two-way configura-
tion and a 90° x 60° pattern. Another example is the EVF-1181S subwoofer, which has a single EVS-18S
18-inch woofer in a “one way” configuration and without a specific coverage pattern (essentially omnidi-
rectional in the very-low-frequency range in which it is usually operated).
Table 1a:
Coverage patterns available in the EVF and EVH series (all rotatable)
Horn Pattern: 40° x 30° 60° x 40° 60° x 60° 90° x 40° 90° x 60° 90° x 90° 120° x 60°
EVF 12-inch ••••••
EVF 15-inch ••••••
EVH ••••••
Electro-Voice EVF/EVH User Manual 5
Typical EVF and EVH systems are shown in Figure 1, with key dimensions, suspension points, weights
and centers-of-gravity. Engineering data sheets for each model, containing full specifications and dimen-
sional drawings, are shipped with each loudspeaker and are downloadable from the Electro-Voice Web
site (www.electrovoice.com).
Table 1b:
Model number scheme, showing the meaning of each individual model number
Model Name
(As Shown) EVF-1122S/96 (example)
Model Name
(Separated) EVF - 1 2 S /12 96
Description
Loudspeaker
Family/Series
(EVF Series)
Number of
Woofers
(1 Woofer)
Woofer
Diameter
(12-inch)
Number of
Band Passes
(Two-Way)
Woofer
Series Used
(SMX Series)
Coverage
Pattern
(90° x 60°)
1.0 Introduction (cont.)
Figure 1a:
Key dimensions, suspension points, weight, and center-of-gravity for EVF-1122 (all coverage patterns)
Figure 1b:
Key dimensions, suspension points, weight, and center-of-gravity for EVF-1152 (all coverage patterns)
Front ViewEnd View Side View Rear View
“S” System Weight -
60.0 lb (27.2 kg)
Front ViewEnd View Side View Rear View
“S” System Weight -
70.1 lb (31.8 kg)
“D” System Weight -
65.5 lb (29.7 kg)
“D” System Weight -
75.7 lb (34.4 kg)
Electro-Voice EVF/EVH User Manual
1.0 Introduction (cont.)
Figure 1c:
Key dimensions, suspension points, weight, and center-of-gravity for EVF-1121S
Front ViewEnd View Side View Rear View
System Weight -
57.7 lb (26.2 kg)
Figure 1d:
Key dimensions, suspension points, weight, and center-of-gravity for EVF-1151S
Figure 1e:
Key dimensions, suspension points, weight, and center-of-gravity for EVF-1181S
System Weight -
62.6 lb (28.4 kg)
Front ViewEnd View Side View Rear View
System Weight -
101.2 lb (46.0 kg)
Front ViewEnd View Side View Rear View
6
Electro-Voice EVF/EVH User Manual
Figure 1f:
Key dimensions, suspension points, weight, and center-of-gravity for EVF-2121S
Figure 1g:
Key dimensions, suspension points, weight, and center-of-gravity for EVF-2151D
Figure 1h:
Key dimensions, suspension points, weight, and center-of-gravity for EVH-1152 (all coverage patterns)
System Weight -
82.4 lb (37.4 kg)
Front ViewEnd View Side View Rear View
System Weight -
117.0 lb (53.1 kg)
Front ViewEnd View Side View Rear View
“S” System Weight -
143.0 lb (64.9 kg)
Front ViewEnd View Side View Rear View
1.0 Introduction (cont.)
7
“D” System Weight -
145.5 lb (66.1 kg)
Electro-Voice EVF/EVH User Manual
1.0 Introduction (cont.)
Figure 1h:
Key suspension point dimensions for EVF or EVH loudspeakers as indicated in table below
Figure 1g:
Key dimensions for washers and eyebolts included with each loudspeaker
Washer (x4) Eyebolt (x4)
End View Side View Rear View
Table 2:
Key suspension point dimensions as shown in figure above
Dimension: A B C D E°
EVF 12-inch 4.176” [106.07mm] 14.301” [363.24mm] N/A 16.129” [409.67mm] 15°
EVF 15-inch 4.176” [106.07mm] 14.301” [363.24mm] N/A 18.353” [466.16mm] 15°
EVF Subs 3.957” [100.50mm] 13.889” [352.77mm] 23.857” [605.97mm] 28.255” [717.68mm] 10°
EVH 3.957” [100.50mm] 13.889” [352.77mm] 23.857” [605.97mm] 26.409” [670.79mm] 10°
8
Electro-Voice EVF/EVH User Manual
1.0 Introduction (cont.)
1.1 Finishes and Colors Available
The standard EVF/EVH indoor versions are finished in tough EVCoat. In addition, all models are available
in two levels of weather resistance, indicated by letters following the coverage-pattern numbers. The FG
versions, e.g., EVF-1152S/64-FGB, are designed for full weather exposure and feature a fiberglass-
finished enclosure, stainless-steel hydrophobic grille and the CDG dual-gland-nut input-panel cover. The
PI versions, e.g., EVF-1152S/64-PIW, are rated for indirect outdoor exposure only in protected areas,
such as under a roof overhang, and feature a stainless-steel hydrophobic grille and CDG
dual-gland-nut input-panel cover on an enclosure finished in standard EVCoat. External fasteners on all
systems are stainless steel.
All EVF and EVH systems are available in black or white. Black is indicated by BLK or B at the very end of
the complete model number and white is indicated by WHT or W at the very end of the complete model
number, e.g., EVF-1152/94-BLK and EVF-1152S/94-PIW.
1.2 EVF Front-Loaded Series
Note that engineering data sheets with complete specifications are packed with each system and
downloadable at www.electrovoice.com.
EVF-1122S/64, EVF-1122S/66, EVF-1122S/94, EVF-1122S/96, EVF-1122S/99, EVF-1122S/126,
EVF-1122D/64, EVF-1122D/66, EVF-1122D/94, EVF-1122D/96, EVF-1122D/99, EVF-1122D/126:
two-way 12-inch full-range systems with six different rotatable waveguides ranging from 60° x 40° to
120° by 60°, as detailed in Table 1.
EVF-1152S/43, EVF-1152S/64, EVF-1152S/66, EVF-1152S/94, EVF-1152S/96, EVF-1152S/99,
EVF-1152D/43, EVF-1152D/64, EVF-1152D/66, EVF-1152D/94, EVF-1152D/96, EVF-1152D/99:
two-way 15-inch full-range systems with six different rotatable waveguides ranging from 40° x 30° to
90° by 90°, as detailed in Table 1.
EVF-1121S: 12-inch low-frequency system.
EVF-1151S: 15-inch low-frequency system.
EVF-1181S: 18-inch subwoofer system.
EVF-2121S: Dual 12-inch low-frequency system.
EVF-2151D: Dual 15-inch subwoofer system.
1.3 EVH Horn-Loaded Series
Note that engineering data sheets with complete specifications are packed with each system and
downloadable at www.electrovoice.com.
EVH-1152S/43, EVH-1152S/64, EVH-1152S/66, EVH-1152S/94, EVH-1152S/96, EVH-1152S/99,
EVH-1152D/43, EVH-1152D/64, EVH-1152D/66, EVH-1152D/94, EVH-1152D/96, EVH-1152D/99:
two-way 15-inch full-range systems with six different rotatable high-frequency waveguides ranging from
40° x 30° to 90° x 90° and mid-frequency waveguide contours, as detailed in Table 1.
9
Electro-Voice EVF/EVH User Manual
2.0 Tool List
Listed below are the tools required to prepare EVF and EVH systems for installation:
1. 3/16-inch flat-blade screwdriver (for attaching signal wires to input-panel connectors).
2. Phillips #2 screwdriver (for grille removal to rotate waveguides, removal of high-frequency
waveguides for rotation, and removal of input panel to install the optional TK-150
70.7/100-volt transformer).
3. 4-mm Allen (hex) wrench (for removal and reorientation of the EVH hard foam
mid-frequency waveguide contours to rotate the mid-frequency coverage pattern).
4. 6-mm Allen (hex) wrench (for working with all rigging points).
1.0 Introduction (cont.)
1.4 Accessories for EVF and EVH Systems
Note that some accessories are supplied with certain system versions, as noted.
CDG: optional dual-gland-nut input-panel cover to protect the input connections from water. Note that
this cover is supplied with the weather-resistant versions.
CSG: optional single-gland-nut input-panel cover to protect the input connections from water.
CDNL4: optional input-panel cover equipped with dual Neutrik Speakon® NL4M connectors, providing a
quick-disconnect alternative to the standard Phoenix screw-terminal input connectors.
HRK and VRK: a series of horizontal (HRK) and vertical (VRK) rigging kits that accommodate a number
of horizontal and vertical system aiming angles. See section 5.0 EVF and EVH Rigging System for details.
TK-150: optional 70.7/100-volt transformer kit mounts on the inside of the EVF and EVH input panels,
offering 37.5, 75 and 150 watts at 70.7 volts and 75 and 150 watts at 100 volts. Installation instructions
come with the TK-150.
EVF-UB: optional U-bracket kit for mounting single EVF full-range and low-frequency (not subwoofer)
systems to a wall or ceiling. Installation instructions come with the EVF-UB.
EVI-M10K: optional eyebolt kit, consisting of four M10 shoulder eyebolts and four fender washers, used
when additional eyebolts are needed to suspend loudspeakers. See section 6.3 for details. One EVI-
M10K eyebolt kit is supplied with each loudspeaker system.
EVI-AC: optional access card which allows diagnostic access to the transducers and protection circuitry
inside the enclosure. Use of this accessory does not require any disassembly or disconnections beyond
removal of the plug-in switch card.
10
Electro-Voice EVF/EVH User Manual
3.0 Designing an EVF/EVH Cluster
3.1 General Aiming and Placement Guidelines
Loudspeakers should be “pointed at the people” and away from reflective room surfaces. Since people
are excellent absorbers of sound and room surfaces are often not, this practice insures not only that the
audience will receive the high frequencies necessary for good voice intelligibility and musical clarity but
also that the reflective surfaces do not energize the room with intelligibility-robbing reverberation.
Loudspeakers for sound reinforcement are usually located high above a stage or platform and aimed
down and out into the audience. This minimizes the difference between the longest throws to the rear of
a venue and the shortest throws to the front rows, promoting coverage uniformity. Note that the typical
portable loudspeaker on a short, 6-foot stand cannot duplicate such uniformity since the distant seats are
so much farther away than the front rows. The direct sound from a loudspeaker drops 6 dB every time the
distance from it doubles, according to the formula:
Level loss (dB) = 20log10(closest distance/farthest distance).
See comments on the audibility of different dB differences in section 3.4 Coverage-Uniformity Target.
3.2 Choosing between the EVF Full-Range and the EVH Full-Range Systems
When the reverberation time of a room (formally called T60 and the time it takes sound, once the source
has stopped, to decay by 60 dB) exceeds 2-2.5 seconds at mid frequencies, the horn-loaded EVH series
should be used. The EVH’s low-frequency horn mouth is large enough to control the rated coverage
pattern down to 500 Hz, which promotes clarity by keeping more sound off of reflective surfaces than can
the smaller, 12-inch-square horns and direct-radiating woofers of the EVF series. This concept is explored
in more detail below.
3.21 Directivity Break Frequency Defined
Below a certain frequency, the mouth size of a waveguide is no longer large enough to maintain the
nominal coverage angle and the coverage angle gets wider and wider as frequency is decreased. The
frequency at which this occurs is called the “directivity break frequency” (fb) and is inversely proportional
to the size of the waveguide mouth and the nominal coverage angle of the waveguide. The directivity break
frequency can be approximated by the following formula:
fb (Hz) = 1,000,000/[angle (degrees) x dimension (inches)].
11
Electro-Voice EVF/EVH User Manual
3.0 Designing an EVF/EVH Cluster (cont.)
3.3 More on Coverage Patterns, Multiple Coverage Patterns, the Need for Clusters of Loud-
speakers and How Far a Single Cluster Can “Reach” into a Venue
The coverage patterns or angles mentioned previously are defined where loudspeaker output is 6 dB
down from maximum, usually on-axis level. In order to help cover only the absorptive audience with sound,
given different trim heights and the wide variety of venue shapes, the EVF and EVH series are offered in
the many coverage patterns listed in Table 1 (above). Even with this wide choice, it is relatively unlikely that
a single loudspeaker will cover the audience uniformly. Therefore, two or more loudspeakers are often as-
sembled into clusters and aimed in different directions in order to reach the entire audience.
3.31 Basic Clustering Guidelines
The aiming angles of systems in a cluster are related not only to room geometry but also to the particular
coverage patterns selected. A rough design can be based on the plan and elevation views of a room, rep-
resenting the loudspeakers by the angles of their horizontal and vertical coverage patterns, e.g., 60° x 40°.
A wide or “short throw” coverage pattern, such as 120° x 60°, is good for aiming down into the front rows
of a rectangular venue to reach all of the seats left to right. Narrower patterns, such as 60° x 40° and
40° x 30°, are appropriate as “long throw” devices that send sound to the rear of the audience without
also “blasting out” the front rows.
For more accurate coverage modeling, EASE data is available on product pages and in the download
section of the Electro-Voice website, www.electrovoice.com.
A common practice is to widen the horizontal coverage of a single loudspeaker by placing two systems
side by side and aiming them in such a way that their horizontal patterns do not overlap. Individually, each
system will be 6 dB down at the overlap point. Together at the overlap point, they will sum coherently to
the 0-dB on-axis level. A specific example is two 60° horizontal systems clustered together with their axes
placed 60° apart.
If these two systems are “underlapped,” with, say, their axes 75° apart, the overall coverage angle will be
wider but the level near the array axis will drop. If the two systems are overlapped to any great degree,
e.g., their axes only 45° apart, the overall coverage angle will be reduced and the interference discussed
in section 3.5 Multiple-Source Interference in Clusters will be worsened.
The degree to which long-throw devices can extend the region of uniform coverage is limited. A single
loudspeaker will typically “reach” to the rear a distance that is about twice that of the distance to the clos-
est front row. See Figure 2.
12
Electro-Voice EVF/EVH User Manual 13
Figure 2:
Typical “reach” of a single loudspeaker
into a venue (DI ) in order to maintain
the desired ±3 dB coverage is about
two times the distance to the closest
seats (DS )
3.0 Designing an EVF/EVH Cluster (cont.)
Adding a long-throw device will typically extend this reach to about three times the closest distance. See
Figure 3.
Figure 3:
Adding a long-throw device extends the reach to about three times the distance to the closest seat
For reaches beyond this, loudspeakers can be suspended over the audience, with their signal delayed
with respect to the front or source loudspeakers so that the sound image will appear to come from the
front of the room. The details of these design tips are beyond the scope of this manual and should be left
to experienced design personnel.
3.4 Coverage-Uniformity Target
A good uniformity target is ±3 dB throughout the audience area, particularly in the 2,000- and 4,000-Hz
octave bands, the bands most important for intelligibility. Such coverage should also be achieved in the
8,000-Hz band, important for “sparkle.” As a reference, a 1-dB level difference is nearly imperceptible, a
3-dB difference is noticeable but not a large change, a 6-dB change is clearly noticeable and a 10-dB
change is twice or half as loud. The ±3-dB uniformity target is related to these perceptual differences.
Electro-Voice EVF/EVH User Manual14
3.5 Multiple-Source Interference in Clusters
Whenever two or more sources serve a single venue, some seats will receive strong signals from multiple
sources. Consider two EVF-1122S/64 60° x 40° systems clustered side by side with their axes 60° apart
to form a 120° x 40° cluster. If these systems maintained their rated coverage patterns into the low-
frequency range, there would be essentially no interference. But the 12-inch-square waveguides used in
the EVF series will begin to “balloon out” at about 2 kHz and below, an effect discussed in Section 3.21
Directivity Break Frequency Defined, above.
On the axis of the cluster, the output of both systems sums perfectly, since the listener is equidistant from
each system and the output of both reaches the listener at the same time. This is the axis-of-cluster line
shown in Figure 4. If the listener moves to the left (as viewed in the figure), the left loudspeaker will be
closer and the sound will arrive sooner. At some angle and at some frequency, the time difference will be
equivalent to reversing the polarity of one signal, causing a complete cancellation of cluster output at that
frequency.
Figure 4:
The two loudspeaker sources sum perfectly only on the axis of the cluster (as shown);
to the left and right of this axis, distance differences produce arrival-time differences
that cause cancellation of some frequencies (see text for more details)
3.0 Designing an EVF/EVH Cluster (cont.)
Electro-Voice EVF/EVH User Manual 15
Figure 5:
Typical response off the array axis of the two loudspeakers shown in Figure 4,
showing cancellations due to arrival-time differences
This effect is shown in the frequency-response of Figure 5. Given the dimensions of the typical compact
loudspeaker systems and when they are clustered in close proximity to one another, the first several
interference nulls occur right in the middle of the vocal range. A frequency response with these ever-
more-closely spaced nulls is known as a “comb filter” response, after the visual appearance of the
response.
3.0 Designing an EVF/EVH Cluster (cont.)
If one of the null frequencies is chosen and the horizontal polar response is measured, the result is shaped
like the blue polar response in the center lower graph of Figure 6. In this view, the cluster axis points up
(+X). Full output is achieved on this axis, since both signals arrive at the same time. But there are off-axis
problems. While the overall coverage of the cluster is about 120° (6 dB down), two deep nulls occur at
about 20° on either side of the cluster axis.
Figure 6:
Horizontal polar response (blue center
plot) of two closely clustered 60° x 40°
loudspeakers aimed 60° apart, showing
the off-axis nulls at 1,250 Hz caused by
multiple-source interference
(see text for more details)
NORMALIZED
Electro-Voice EVF/EVH User Manual16
At higher frequencies, the interference patterns become more densely packed, which essentially elimi-
nates their audibility. Figure 7 shows this effect at 8,000 Hz.
3.51 Reducing Multiple-Source Interference
Multiple-source interference cannot be eliminated but it can be substantially reduced. Systems which
have radiating devices large enough to hold their rated coverage angles down to relatively low frequen-
cies, such as the horn-loaded EVH series that hold their coverage angles down to 500 Hz, will exhibit
less interference in clusters. Also, doubling the distance between the two systems of Figure 8 produces
multiple interference nulls which are more densely packed than those of Figure 6, reducing the audibility of
the interference.
Figure 7:
Horizontal polar response (blue center
plot) of two closely clustered 60° x 40°
loudspeakers aimed 60° apart, showing
multiple, densely packed off-axis nulls
at 8,000 Hz caused by multiple-source
interference (see text for more details)
3.0 Designing an EVF/EVH Cluster (cont.)
Figure 8:
Horizontal polar response (blue cen-
ter plot) of two 60° x 40° loudspeakers
aimed 60° apart but with double the
distance between grille centers compared
to Figures 6 and 7, showing the more
densely packed 1,250-Hz off-axis nulls
caused by multiple-source interference
(see text for more details)
Electro-Voice EVF/EVH User Manual 17
One clustering technique that accomplishes this separation without putting a physical space between two
full-range systems is putting a low-frequency or subwoofer system between two full-range systems. Such
a cluster is shown in Figure 9, assembled with the optional HRK rigging kits.
Figure 9:
A way of separating two full-range loudspeakers to reduce the audibility of multiple-source interference
by separating them with a subwoofer (see text for more details)
3.0 Designing an EVF/EVH Cluster (cont.)
Note: Loudspeakers
are non-specific and
shown as an example.
EVF Full-Range
System
EVF Subwoofer
EVF Full-Range
System
HRK-2 Kit
(Sold Separately)
HRK-2 Kit
(Sold Separately)

Produkt Specifikationer

Mærke: Electro-Voice
Kategori: Højttaler
Model: EVF-1152S 96

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro-Voice EVF-1152S 96 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Electro-Voice Manualer

Electro-Voice

Electro-Voice EVH-1152S/99 Manual

22 Januar 2025
Electro-Voice

Electro-Voice XLE191-FG Manual

8 Januar 2025
Electro-Voice

Electro-Voice Sx600 Manual

8 Januar 2025
Electro-Voice

Electro-Voice Sb122 Manual

8 Januar 2025
Electro-Voice

Electro-Voice Tour X TX1122FM Manual

2 Oktober 2024
Electro-Voice

Electro-Voice EVID C10.1 Manual

2 Oktober 2024
Electro-Voice

Electro-Voice EVID-40C Manual

19 September 2024
Electro-Voice

Electro-Voice EVA-1151D Manual

16 September 2024
Electro-Voice

Electro-Voice EVC-1082-00 Manual

7 September 2024
Electro-Voice

Electro-Voice Sx100+ Manual

4 September 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Klipsch

Klipsch Synergy KSF-C5 Manual

10 April 2025
Klipsch

Klipsch Synergy KSF-S5 Manual

10 April 2025
Panasonic

Panasonic SC-BMAX10 Manual

9 April 2025
Audiofrog

Audiofrog GB40 Manual

8 April 2025
JBL

JBL Stage 250 Manual

7 April 2025
JBL

JBL Conceal C62 Manual

7 April 2025
JBL

JBL Conceal C83 Manual

7 April 2025
Grundig

Grundig Jam 2 Manual

6 April 2025
Elipson

Elipson W35 Manual

5 April 2025
Turbosound

Turbosound Manchester MC15-RS Manual

4 April 2025