Eltako EVA12-32A Manual

Eltako Måling EVA12-32A

Læs nedenfor 📖 manual på dansk for Eltako EVA12-32A (1 sider) i kategorien Måling. Denne guide var nyttig for 40 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

! Note: Select english language!*

Maximum current 32 A, standby loss

0.5 watt only.

Modular device for DIN-EN 60715 TH35 rail

mounting. 1 module = 18 mm wide, 58 mm

deep.

The energy consumption indicator EVA12

uses the current between input and out put

to measure active energy in the same way

as a single-phase power meter. It saves

the consumption parameter in a nonvolatile

memory.

Like all meters without declaration of

conformity (e.g. MID), this meter is not

permitted for billing.

Accuracy conforms to Class B MID (1%) like

all Eltako single-phase energy meters, the

inrush current is 20 mA.

In this way the energy consumption indicator

reproduces exactly the reading on the billing

energy meter installed at a different location

in the building.

The display is subdivided into 3 elds.

■

Field 1:

This display refers to the

cumulative value in eld 3.

|||| moving slowly to the right = Field 3

shows the cumulative consumption since

last reset. This is the display standard

mode.

H01 = Field 3 shows the consumption for

the last hour up to H24 = 24 hours ago.

D01 = Field 3 shows the consumption for

the last day up to D31 = 31 days ago.

Energy consumption indicator

EVA12-32A with display

Temperature at mounting location:

-10°C up to +55°C.

Storage temperature: -25°C up to +70°C.

Relative humidity:

annual average value <75%.

28 032 411 - 2

Only skilled electricians may install this

electrical equipment otherwise there is

the risk of re or electric shock!

M01 = Field 3 shows the consumption for

the last month up to M12 = 12 months ago.

Y01 = Field 3 shows the consumption for

the last year up to Y24 = 24 years ago.

■ Field 2:

Instantaneous values of energy

consumption (active power) in watt (W) or

kilowatt (kW). The display arrows on the

left and right show the automatic change

W and kW.

■ Field 3:

Cumulative value in kWh. Dis play

up to 9,999 kWh with 3 decimal digits,

from 10 kWh with 1 decimal digit and from

1000kWh without decimal digit.

* Press the left button MODE to scroll down

the display options which are shown in eld 1:

H01, D01, M01 and Y01 as described above.

Finally, press MODE to show the abbreviation

of the set language, e.g. GB for English, D

for German and F for French.

Press the right button SELECT once within

the display options to increment the indicated

gure by 1. The corresponding value is indi-

cated in eld 3.The last clock hour then

becomes the hour before last, etc.

If the active language was selected with

MODE, press SELECT to switch to a different

language. Exit the new language setting by

pressing MODE to activate the setting.

The program returns to the standard display

mode automatically if MODE or SELECT are

not operated for 20 seconds or if you press

both buttons briey simultaneously.

Reset

To start saving the values to the nearest

hour, we recommend performing a reset at

an opportune moment after installation.

Hold down the buttons MODE and SELECT

simultaneously for a further 3 seconds until

RES appears. Then press SELECT briey to

reset all memories. Afterwards the program

returns automatically to standard display

mode.

Error messages

■ F01 is shown in the display at incorrect

direction of current.

■ If the voltage drops below 170 V, F02 is

shown on the display.

Typical connection

Technical data

Operating voltage, 230 V, 50 Hz,

extended range -20%/+15%

Reference current

ref 5 (32) A

(Limiting current

max)

Internal power consumption 0.5 W

active power

Display active power LC display

Accuracy class for ±1% B

Inrush current according to 2O mA

accuracy class B

Operating temperature -10/+55°C

Protection degree lP50 for mounting in

distribution cabines with

protection class IP51

Maximum conductor 6 mm2

cross section 1)

Recommended 0,8 Nm (max. 1.2 Nm)

torque 2)

1) The carrying capacity of cables and wires is dened

in DIN VDE 0298-4.

2) The torques for screw terminals are mentioned in

DIN EN 60999-1.

To avoid damages at the energy meter, the

recommended torque values for each terminal

must not be exceeded!

Must be kept for later use!

We recommend the housing for

operating instructions GBA14.

Eltako GmbH

D-70736 Fellbach

Technical Support English:

+49 711 94350025

technical-support@eltako.de

eltako.com

13/2021 Subject to change without notice.

The strain relief clamps of the

terminals must be closed, that

means the screws must be

tightened for testing the function

of the device. The terminals are

open ex works.

Produkt Specifikationer

Mærke:	Eltako
Kategori:	Måling
Model:	EVA12-32A
Type:	Elektronisk
Vekselstrømsindgangsfrekvens:	50 Hz
Bredde:	18 mm
Dybde:	58 mm
Produktfarve:	Blå
Skærmtype:	LCD
Indgangsspænding:	230 V
Måleenhed:	kWt
Målefunktioner:	Strømudgang
Anvendelse:	Indenlandsk