Eltako FT55R Manual


Læs nedenfor 📖 manual på dansk for Eltako FT55R (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
GB
Wireless pushbutton internal frame
dimensions 55x55mm with radius, 15mm
high. Generates the power for wireless
telegrams itself when the button is pressed,
therefore there is no connecting wire and no
standby loss.
For Busch Reflex and Duro cover frames.
The scope of supply comprises a rocker,
a double rocker, a mounting base (all
same colour), the wireless module and
one adhesive foil.
Wireless pushbuttons with one rocker can
transmit two evaluable signals: press rocker
up and press rocker down. Wireless
pushbuttons with double rocker can transmit
four evaluable signals: press two rockers up
or down.
The mounting base can be screwed onto a
flat surface or glued to the wall, on glass or
on furniture using the enclosed adhesive foil.
Use the sleeves in the 55 mm socket box
forscrew mounting. Then the wireless push-
button lighting FTB can be snapped into the
mounting plate from the rear.
The double rocker is snapped onto the
wireless module at the factory. If the double
rocker is replaced by the large rocker, remove
the rocker halves by pulling off to the front.
Do not bend towards the middle. Then snap
the large rocker so that the markings 0 and I
on the back line up with the same markings
on the wireless module.
Adhesion: First adhere the set comprising
the mounting base, frame and attachment
frame - with the latches pointing at the top
and bottom. Then snap on the set comprising
the wireless module and rocker - with the
marking 0 on the back always pointing up.
30 000 225 - 1
Wireless sensor
Pushbutton FT55R-
Teaching-in wireless sensors in wireless
actuators
All sensors must be taught-in into the
actuators so that they can detect and
execute commands.
The teach-in process is described in the
operating instruction of the actuators.
08/ 2012 Subject to change without notice.
Before screwing, remove the mounting base
from the frame and the attachment frame. To
do this, press the latches on the mounting
base outwards. Then screw the mounting
base - with the latches at top and bottom -,
snap on the frame with the attachment frame
and snap on the set comprising the wireless
module and rocker - with the marking 0 on
the back always pointing to the top.
We recommend sheet metal countersunk
screws 2.9x25mm, DIN 7982 C, for
screw connections. Both with rawl plugs
5x25mm and with 55mm switch boxes.


Produkt Specifikationer

Mærke: Eltako
Kategori: Ikke kategoriseret
Model: FT55R

Har du brug for hjælp?

Hvis du har brug for hjælp til Eltako FT55R stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Eltako Manualer

Eltako

Eltako MS Manual

31 August 2024
Eltako

Eltako FT4F-rw Manual

30 August 2024
Eltako

Eltako FT4F-wg Manual

30 August 2024
Eltako

Eltako FTN14 Manual

30 August 2024
Eltako

Eltako FT55R Manual

30 August 2024
Eltako

Eltako FUD71L Manual

30 August 2024
Eltako

Eltako FTS14EM T Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024