Emko ECO PID+ Manual

Emko Temperaturregulator ECO PID+

Læs gratis den danske manual til Emko ECO PID+ (4 sider) i kategorien Temperaturregulator. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Emko ECO PID+, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Eco PID+, PID Temperature Control Un t�

- 4 d g t process (PV) and 4 d g t set (SV) d splay� � � � �

- Temperature sensor �nput (TC,RTD)

- Programmable ON/OFF, P, PI, PD and PID control forms

- Adaptat on of PID Coeff c ents to the system w th Self-Tune and Auto-Tune � � � �

- Programmable Heat ng or Cool ng Funct ons for Control Output � � �

- Selectable Alarm Funct ons for Alarm Output�

- Ser al RS485 Commun cat on (opt onal)� � � �

Introduct�on Brochure. ENG EcoPID+ 01 V00 03/22

Easy Access D agram For Program Parameters�

Panel Mount ng�

Enter Password w th ncrement� �

or decrement buttons.

Approve password

w th Enter button�

Password Screen

Eco ser es temperature controllers are des gned for measur ng and controll ng a � � � �

temperature value. They can be used n many appl cat ons w th the r TC and RTD � � � � �

temperature measurement nput, mult -funct on control outputs, selectable alarm � � �

funct ons.�

They are ma nly used � �n glass, plast c, petro-chem stry, text le, automot ve and mach ne � � � � �

product on � � �ndustr es. Accurate and advanced controll ng � �s performed w th selectable �

ON-OFF, P, PI, PD, PID and Self Tune/Auto Tune PID funct ons.�

SPECIFICATIONS

Process Input: Thermocouple (TC): J, K, R, S, T and L (IEC584.1)(ITS90)

Thermores stance (RTD): Cu-50 and PT-100 (IEC751)(ITS90)�

Measurement Range: Please refer to process �nput type select on � �n process menu

parameters sect on.�

Accuracy:

Thermocouple (TC):( ± 0.25% of full scale or ± 3ºC, wh ch one � �s greater) ±1 d g t max. � �

Thermores stance (RTD):( ± 0.25% of full scale or ± 2ºC, wh ch one � � �s greater) ±1 d g t � �

max.

Cold Junct on Compensat on:� � Automat cally ±0.1°C/1°C�

L ne Compensat on:� � Max mum 10 Ohm�

Sensor Break Protect on:� Upscale

Sampl ng Cycle: �0.1 second

Input F lter:� Programmable

Control Form: ON/OFF, P, PI, PD or PID (Control form can be programmed by the user)

OUTPUT

Process Output: Relay (5A@250V at res st ve load) or SSR Dr ver Output V� � �

(Max mum 10mA, Max. 12V )�Z

Alarm Output: Relay (5A@250V at res st ve load)V� �

SUPPLY VOLTAGE (It must be determ ned � �n order)

230V (±15%) 50/60Hz - 4VAV

115V (±15%) 50/60Hz - 4VAV

100-240V 50/60Hz - 4VAV

24V (±%15) 50/60Hz - 4VAV

24V (±%15) 50/60Hz - 4VAW

10...30V - 4W Z

DISPLAY

Process D splay:� 16 mm Red 4 d g t LED D splay� � �

Set Value D splay:� 9 mm Orange 4 d g t LED D splay� � �

Led Ind cators:� PO1 (SSR Process Output Status Led), PO2 (Relay

Process Output Status Led), AL1, AL2 (Alarm Output Status Leds),

ºC, ºF LEDs

ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS

Operat ng Temperature:� 0...50ºC

Hum d ty :� � 0-90%RH (none condens ng)�

Mechan cal Impacts: �1Joule (IK06)

Protect on Class: �NEMA 4X (IP65 at front, IP20 at rear)

We ght:� 150 gr.

D mens on:� � 48 x 48 mm, Depth: 86,5 mm

Panel CutOut: 46 x 46 mm

*1 - ON/OFF Hysteres s parameter s not act ve unless parameter s set as .� � � �

*2 - Soft Start parameters( , , ) s not act ve unless parameter s set as .� � �

*3 - Soft Start Control Output and Soft Start Control T me parameters s not act ve f parameter� � � �

s set as .�

*4 - PID control parameters are not act ve unless parameter s set as .� �

*5 - Alarm-2 parameters are not act ve f parameter s set as .� � �

*6 - Commun cat on parameters are not act ve on dev ces have no commun cat on module.� � � � � �

*7 - If s d fferent from 0 and user enters to program menu w thout enter ng the password� � � �

Prot menu s not shown.�

Note: User can ex t from any parameter screen w thout sav ng the values by press ng button. If � � � �

no operat on for 120 seconds, dev ce automat cally return to ma n screen. � � � �

Easy Access D agram For Sensor Break Output�

Value From Ma n Screen�

Change the sensor break

output value w th ncrement� �

or decrement buttons.

Press Enter button to save

new sensor break output value

and ex t.�

Ma n Screen Ma n Screen� �

Note1: User can ex t from parameter screen w thout sav ng the � � �

values by press ng button. If no operat on for 120 seconds, dev ce � � �

automat cally ex ts from parameter screen.� �

Note2: Sensor break output value can be adjusted on programm ng �

sect on too.�

Tune Operat on�

Start ng the Tune operat on� �

1- Enter to the parameter n menu and select �

or ,then press button for sav ng parameter and turn to ma n � �

screen. Or eas ly press button for 3 seconds* n ma n screen.� � �

2- Observe that bl nks n set d splay.� � �

*Only Self Tune can be started by th s way.�

Cancel ng Tune operat on:� �

1- If sensor breaks;

2- If tune operat on can not be completed n 8 hours;� �

3- Wh le heat ng self tune s runn ng, f process value becomes � � � � �

greater than process set value;

4- Wh le cool ng self tune s runn ng, f process value becomes less � � � � �

than process set value;

5- Wh le tune operat on s runn ng, f user changes the process set � � � � �

value;

6- Wh le tune operat on s runn ng, f user changes the � � � � �

parameter n menu; �

Then tune operat on s canceled, dev ce cont nues to run w th former � � � � �

PID parameters w thout chang ng PID parameters.� �

PID TEMPERATURE CONTROL UNIT

PID+

Eco

D mens ons� �

48 mm / 1.89 nch�

6 mm / 0.24 nch�80,52 mm / 3.17 nch�

Max mum 9 mm / 0.35 nch� �

1- Before mount ng the dev ce n your panel, � � �

make sure that the cutout s of the r ght s ze.� � �

2- Check front panel gasket pos t on.� �

3- Insert the dev ce through the cutout. If the �

mount ng clamps are on the un t, put out them � �

before nsert ng the un t to the panel.� � �

4- Insert the mount ng clamps to the two of �

des gnated holes that located four s des of � �

dev ce. �

5- Drag the mount ng clamps n d rect on 5 � � � �

unt l the dev ce completely mmob le w th n the � � � � � �

panel.

6- In order to remove dev ce push on the �

mount ng clamp as shown w th arrow 6 and � �

pull back.

Access and Change Set Values

Press ncrement or decrement�

button to change process set value.

Press Enter button to save new

set value and return the ma n screen.�

Ma n ScreenMa n Screen ��

Temperature Set Value Parameter (Default: 200) MODBUS ADDRESS: 40000

Note-1: User can ex t from set value sect on w thout sav ng the values by press ng button. If no � � � � �

operat on for 120 seconds, dev ce automat cally ex ts from Set Value sect on.� � � � �

Note-2: Set value can be adjusted between Set Value Low and H gh L m t ( - ).� � �

Press Program button

to access password screen.

Electr cal W r ngs� � �

To reduce the effect of electr cal no se on dev ce, low voltage l ne (espec ally sensor� � � � �

� � � � � �nput cable) w r ng must be separetely from h gh current and voltage l ne. If poss ble,

use sh elded cable and sh eld must be connected to ground only one s de.� � �

Note-1: External Fuse s recommended.�

Note-2: Stranded cable cross sect on: 1,5mm², Sol d cable cross-sect on: 2,5mm²� � �

The str pp ng length s 7mm to 9mm.� � �

Note-3: Supply cables must comply w th the requ rements of IEC 60277 or IEC 60245.� �

It s adv sed to use a two-pole supply sw tch, des gnated for th s dev ce, w th open/� � � � � � �

closed pos t ons marked, n order to cut the power. It must be placed on the supply � � �

� � �nput of the dev ce at a place where the user can eas ly reach.

V External fuse must be on phase connect on of the supply nput.� �

Z External fuse must be on (+) l ne connect on of the supply nput.� � �

Make sure that the power supply voltage range s su table for the dev ce.� � �

Sw tch on the power supply only after all the electr cal connect ons are n place.� � � �

PO1

(Process Output 1)

SSR Output

12V

Max. 10mA

AL1

(Alarm Output 1)

AL2 / PO2

(Alarm Output 2 or

Process Output 2)

Process

Input

5A@250V

Ser al Commun cat on� � �

(RS485, Modbus RTU) A+

B-

PID+

Eco

PT-100

Supply

Sw tch�

Supply

Voltage

1A T

Fuse

NOTE-1

AL1 / PO2

(Alarm Output 1 or

Process Output 2)

Process

Input

5A@250V

PT-100

The Dev ce �

w th Two Relays�

The Dev ce �

w th One Relay�

Çal ma Ekranış ı

*2,3

*7*6

Produkt Specifikationer

Mærke:	Emko
Kategori:	Temperaturregulator
Model:	ECO PID+

Har du brug for hjælp?

Hvis du har brug for hjælp til Emko ECO PID+ stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Temperaturregulator Emko Manualer

Emko ESM-9420 Manual

7 September 2025

Emko ESM-1520-N Manual

30 August 2024

Emko ECO PID+ Manual

30 August 2024

Emko Eco PID Manual

30 August 2024

Emko Eco Lite Manual

30 August 2024

Emko CHANNEL8A-N Manual

28 August 2024

Emko ESM-7720 Manual

28 August 2024

Emko ESM-3711-CN Manual

28 August 2024

Emko ESM-4410 Manual

27 August 2024

Emko ESM-4435 Manual

27 August 2024

Temperaturregulator Manualer

Nyeste Temperaturregulator Manualer

SRS PTC10 Manual

3 September 2025

Fluke 1504 Manual

2 September 2025

Festo SOEG-S-M18-S-L Manual

18 August 2025

Mueller GS 70.00 knx Manual

18 August 2025

Daikin KRCS01-8B Manual

11 August 2025

Daikin BRC4C61 Manual

11 August 2025

9 August 2025

9 August 2025

9 August 2025

3 August 2025