Erica Synths Sequential Switch Manual

Erica Synths Ikke kategoriseret Sequential Switch

Læs nedenfor 📖 manual på dansk for Erica Synths Sequential Switch (3 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/3
3
4
5
6
7
8
1
2
MAN. STEP
SHIFT
PLAY MODE
MAN. RESET
IN/OUT
RESET
CLK IN
CLK OUT
GATE
IN/OUT
FWD
RND
8PING
PONG
2FWD
1REW
3FWD
1REW
2STEP
PING
PONG
REW
SEQUENTIAL SWITCH
THANK YOU FOR PURCHASING
ERICA SYNTHS MODULE
Erica Synths 8 channel SEQUENTIAL
SWITCH is unique module that allows you
to sequence up to eight sound sources
in advanced ways or route one sound
source sequentially to eight dierent
sound modifiers – VCFs, waveshapers,
VCAs, etc. With Sequential Switch CV
Expander (sold separately) added you get
one of most advanced 8 step sequencers
arround. Enjoy!
Erica Synths Sequential Switch (SS)
unique control interface allows you
to pause, skip and merge steps, set
sequence length, but what really sets it
apart from other sequential switches is
Gate output – when used with ADSR and
VCA, you get really powerful sequencer
with real time control over each sound
source in the sequence. Use Sequential
Switch with random clock source and
you get a heart of insane random, self-
generating patches!
NB! Input signal level for SS should not
exceed 20Vptp (that is rare occasion
in modular synths). Nothing bad will
happen, but you will hear some unwanted
signal on unused outputs.
FEATURES:
8 inputs/outputs sequentially routed to
one input/output
Manual Step and Reset
Gate output (reacts on merged and
paused steps)
8 dierent play modes
Piano mode
TECHNICAL SPECIFICATIONS:
Max input level -10V - +10V ..........................
Power consumption .....................................
......................... +50mA (all LEDs on), -13mA
Module width ....................................... 10HP
Module depth 20mm ...................................
Push Man. Step button to advance
to the next Active step. Push and
hold for 2” Manual Step button,
and the module will go to MANUAL
SELECT mode – you can push any
channel button and manually select
ANY channel, you wish, ignoring
the sequence. LEDs on indicates the
active channel. Gate Out stays high
until you select another channel.
If you are patching Sequential
Switch output to VCA, controlled by
envelope generator, make sure EG
is in ADSR mode with sustain on. To
exit MANUAL SELECT mode, push
Manual Step button promptly.
Push Man. Step and Man. Reset
buttons simultaneously and hold
those for 2” to select PIANO mode –
it works similar to Manual Select
mode, the Gate Out is high only till
you hold the channel button. Patch
the module OUT into VCA and Gate
Out into ADSR envelope generator,
and you have 8 completely dierent
sound keyboard! To exit PIANO
mode, push Manual Step button
promptly
Use buttons to control step states
and sequence length. Initially all
steps are ACTIVE.
Push the button once and relevant
step will go in PAUSE mode – the
signal from relevant input will not
be routed to the output, but the step
will be silenced for one clock period.
You can activate the step again by
pushing the button again.
Push the button quickly twice the
relevant led will go o and the step
will be SKIPEDthe sequencer will
advance immediately to the next
active step.
Hold the button and push another
button next to it – the steps will be
MERGED. In this case the GATE
out will be extended to one Clock
period. Exit the MERGE mode by
pressing any of merged buttons.
Relevant step will become ACTIVE.
SEQUENCE LENGTH (2-8 steps) is
determined by the LAST ACTIVE
step. So, if you want 6 step long
sequence, deactivate steps 7 and 8
(push relevant buttons twice)
Button LEDs indicate the state of
each step:
Bright LED the step is ON
Half-dimmed LED the step is
PAUSED
LED is o – the step is SKIPED
Blinking LED currently active step
Two blinking adjacent LEDs – two
steps are merged
Plug in dierent signal sources, you
want to sequence! If you intend to
use MERGE mode, it’s wise to split
same signal to several Inputs. Also,
if you wish to route one Input to one
of 8 Outputs (one VCO going to
several VCFs/waveshapers step by
step!), feel free to do so!
Push Man. Reset button to reset
sequence to the first step. Push and
hold this button and then push one
of the step buttons to select play
mode
SS will automatically reset to the
first step, when pulse signal is
applied here
Apply Clock signal here (+5V pulse).
On the each rising edge of the
signal, SS will advance to the next
active step
This is Clock Thru jack you can
save on clock dividers and use the
same Clock signal to control other
devices
+5V 20ms gate appears here on
each ACTIVE step. For MERGED
steps the Gate length is equal to one
step length + 20ms
Use this as OUTPUT if you want
to take signals from 8 inputs
sequentially OR use this as INPUT
if you want to route one signal
sequentially to one of 8 outputs
SEQUENTIAL SWITCH AND CV EXPANDER


Produkt Specifikationer

Mærke: Erica Synths
Kategori: Ikke kategoriseret
Model: Sequential Switch

Har du brug for hjælp?

Hvis du har brug for hjælp til Erica Synths Sequential Switch stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Erica Synths Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlona

Atlona AT-DVIF30S-IR Manual

29 December 2024
Atlona

Atlona AT-PRO3HD66M Manual

29 December 2024
Atlona

Atlona AT-3GSDI500 Manual

29 December 2024
BlueBuilt

BlueBuilt BBMAG2M Manual

29 December 2024
Atlona

Atlona AT-3GSDI-14 Manual

28 December 2024
Atlona

Atlona AT-COMP10SS Manual

28 December 2024
Atlona

Atlona AT-2VGA300SL Manual

28 December 2024
Atlona

Atlona AT-HD-V216 Manual

28 December 2024
Atlona

Atlona AT-VGA11S Manual

28 December 2024
True

True TC900 Manual

28 December 2024