Eureka Bonavista 100 Manual

Eureka Tent Bonavista 100

Læs nedenfor 📖 manual på dansk for Eureka Bonavista 100 (2 sider) i kategorien Tent. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Bona Vista 9 Instructions Bona Vista 9 Instructions
Component List
Tent Body
Tent Fly sheet
Equal length main frame poles (2)
Tent bag with 1 internal pole bag
1 bag of stakes and guy lines
Important
It is recommended to set up your tent prior to your first
trip and at the beginning of each camping season to
ensure you are familiar with the set up and the tent is in
proper condition.
Be sure when selecting a tent site that rain water will
drain away from the tent location
Inspect the site and remove any sharp or protruding
objects that could damage the tent floor.
Instructions
1. Unroll the tent separating the components. Assemble the
poles ensuring ferrules are fully connected. You will have
four (4) equal length long main frame poles and one (1)
shorter vestibule pole.
2. Lay out the tent body and slide two frame poles through
the pole sleeves on top of the tent. Always push poles
through sleeves (even when taking down) to ensure fer-
rule connections are complete. Pulling can separate at
ferrules with potential pole breakage when flexing. Poles
when inserted through sleeves will form an X pattern on
the still flat tent.
3. Move to a corner and insert a corner pin into the base
of the pole. Follow the corner seam up to the first tent
clip and attach to the frame. Move to the other end of
the pole, slowly flex the pole and insert the corner tent
ring into this pole end. (If a second person is available
they can hold the pole as it is flexed reducing the stress
on the pole) Follow up this corner seam and attach the
first tent clip to the frame.
4. Repeat step #3 for the second pole.
5. Attach all remaining tent clips to the frame.
6. The inner tent is now up and can be staked down in the
desired location.
7. Take one of the two remaining main poles and position
this horizontally above one of the doors. Note it will
position between the tent body and the already set poles
from previous steps. Nothing has been connected at this
stage. Take one loose end of the pole and flex down
towards the ground. You will locate the ring and pins
along the side of the tent, 2 locations. Use the ring and
pin that is furthest away from the door that the pole is
crossing above. Insert into the pole end. Do the same
procedure with the other end of the pole. Attach all the
tent clips along the pole seam to the pole.
8. Repeat step 7 with the remaining main pole at the other
end of the tent.
9. Stretch the fly sheet over the tent. Connect the fly sheet
and tent at the four corners using the attachments pro-
vided.
Component List
tente
double toit
4 arceaux solidarisés d’armature et 1 arceau solidarisé
pour vestibule
sac pour tente avec un sac interne pour armature
1 sac de piquets et haubans
Important
Il est recommandé de monter la tente avant une pre-
mière sortie et au début de chaque saison de camping
pour se familiariser avec le montage et pour s’assurer
que la tente est en bon état.
Choisissez toujours un site offrant un bon écoulement
des eaux à l’écart de la tente.
Inspectez le site et enlevez tout objet pointu, tranchant
ou protubérant qui pourrait endommager le tapis de
sol.
Montage
1. Dérouler la tente et séparer les composants. Assembler
les arceaux en s’assurant que les bouts sont insérés à
fond dans les viroles. Il s’agit de quatre (4) longs
arceaux d’égale longueur formant l’armature principale
et d’un (1) arceau court pour le vestibule.
2. Étendre la tente puis glisser deux arceaux principaux
dans les gaines d’armature situées sur le dessus de la
tente. Toujours pousser les arceaux (même lors du
démontage) pour assurer l’intégrité du raccordement
dans les viroles. Le fait de tirer les arceaux pourrait
causer la séparation des joints et le bris des arceaux.
Une fois insérés, les arceaux forment un X sur la tente
qui est alors toujours à plat.
3. À l’un des coins, insérer la goupille dans le bout de
l’arceau. Longer la couture depuis le coin jusqu’au pre-
mier crochet d’armature et le fixer à l’arceau. De son
autre extrémité, arquer lentement l’arceau et y insérer
la goupille du coin dans le bout. (Si une seconde per-
sonne est disponible, elle peut tenir l’arceau pendant
qu’il est arqué, pour réduire les contraintes qu’il subit.)
Longer la couture depuis ce coin et fixer le premier
crochet d’armature.
4. Répéter l’étape 3 avec le deuxième arceau.
5. Fixer à l’armature tous les autres crochets.
6. La tente intérieure est maintenant montée et peut être
fixée au sol, à l’aide de piquets, à l’endroit désiré.
7. Placer horizontalement, au-dessus de l’une des portes,
l’un des deux arceaux principaux restants. Noter qu’il se
place entre la tente et les arceaux préalablement mon-
tés. À ce stade-ci, rien n’est raccordé. Fléchir une
extrémité de l’arceau vers le sol. Repérer les 2 emplace-
ments, au côté de la tente, d’un anneau à goupille.
Utiliser l’anneau à goupille qui est le plus éloigné de la
porte au-dessus de laquelle l’arceau se trouve.
Raccorder l’extrémité de l’arceau à la goupille. Répéter
la procédure avec l’autre extrémité de l’arceau. Fixer à


Produkt Specifikationer

Mærke: Eureka
Kategori: Tent
Model: Bonavista 100

Har du brug for hjælp?

Hvis du har brug for hjælp til Eureka Bonavista 100 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Tent Eureka Manualer

Tent Manualer

Nyeste Tent Manualer