Eureka Pine Lodge Manual

Eureka Telt Pine Lodge

Læs nedenfor 📖 manual på dansk for Eureka Pine Lodge (2 sider) i kategorien Telt. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Fan Door
poles
Main
poles
Roof
poles
Wall
poles
Component List:
1 Tent Body with Guy Ropes, 3 Main Poles, 6 Roof Poles, 6 Wall Poles, 4 Fan Door Poles,
1 Carry Bag, 1 Stake Bag/Stakes, 1 Pole Bag
2. Assemble the shock corded
poles and divide according to
size and shape Take care; .
make sure that each pole
section is fully seated into the
next. Do not allow the
sections to snap together as
this can damage the ends.
See fig 2.
1. and separate all the components. Unroll and unfold the Remove from the carry bag
fabric top side up, on a clean, dry space and open the doors. If windy, stake down the
windward corner. See fig 1.
Guy Out: This tent has very large straight walls that act differently in high winds. If there
are high winds, carefully follow the guy out instructions on the back side of this sheet.
Power Port: Open zipper and run extension cord
through opening. Close zipper so that it rests
next to the extension cord. Make sure the
zipper cover is not twisted or tucked The cover .
must lay flat against the outside of the tent to
keep out rain. See fig 15.
Take Down: Remove the poles from the fan door.
Pull up all stakes. Pull wall poles off of the pins
and remove poles. Remove roof poles. Collapse
all poles and sto Fold the tent onto itself then w.
roll up towards the open door and stow.
Options: Floor Saver and Fly/Awning.
Assembly Instructions for
the Pine Lodge Tent
YOUR TENT IS READY !
C
B
A
E
F
D
fig 2
fig 1
fig 5
fig 6
fig 7 fig 8
fig 3
fig 13
fig 14
fig 15
fig 12 fig 14
fig 9
fig 10
3. Build the roof frame. Inset three black roof poles into the nylon elbows on one of
the main poles at and This forms the outer ridge. Move to the opposite side A, B C.
and again fit the same three poles into the nylon elbows of a second main pole at , D
E F. and This forms one half of the roof. See fig 3 and 4.
3. with the remaining three roof poles Continue
and main pole on the opposite side to
complete the roof assembly.
See fig 5.
4. Attach the fabric to the roof
frame. Hook the shockcorded
J-hooks to the brass rings
and to the holes in the
elbows.
Snap the web clips to the poles. It is best to start in the center and work your way out You .
must do this now because you won’t be able to reach the clips and hooks once the walls
are raised. See fig 6, 7 and 8.
NOTE: If you intend to install the optional fly/awning, do no It is far easier to attach the w.
fly/awning while the roof is still on the ground.
Installation of the Optional Fly/Awning:
Step I: Lay the Fly out on the ground in front of the tent, with the awning to the far front.
Step II: With 2 people, grab the rear corners of the Fly & walk it over the top of the frame
from front to back.
Step III: There are 6 frame extensions, 1 each at the ends of the center ridge and eave
poles front and rear. See fig 9 positions A,B, D, E, F- position C not visible. At the rear of
the Fly, slide the 3 extensions in to the pockets sewn on the Fly (positions A, B, C).
Repeat this step along the front of the tent at positions D, E & F. [Continue with tent
set-up at number 5 'Raise the tent'.]
Step IV: Once the tent is completely set up and staked out, insert the awning poles and
stake them out. See fig 11.
NOTE When properly seated, the small :
spring on the pole will click into place.
5. Start on one side and insert Raise the tent.
gray wall poles into the elbows. Locate the web
ring/pins attached to the floor of the tent. Insert
a pin into the base of each pole. See fig 9 & 10.
Repeat on the other side until the tent is at full
height and freestanding.
7. Assemble the fan door frame. Slide the
fiberglass fan door poles, rubber end up, into
the bottom of the door sleeves. Insert pins
from the web loop into the bottom of these
poles. See fig 12 & 13 Tuck the door into its .
perimeter envelope.
There is a web loop on each side of the fan
door, stake these down.
8. Attach the splash guard. To provide an
extra layer of protection, there is a flap that
runs across the bottom near the inside of
the door. Attach the J-hooks from this flap to
loops at the front corners. See fig 14.
6. . Stake Stake the tent down
out the corner rings first As .
you work your way around the
tent apply tension to square
the tent and pull out any floor
wrinkles Align the center .
poles with the corners and
stake out web side rings. See
fig 12. [If you have the
Fly/Awning option, now
complete 'Step IV'.]
Important: Make sure the
bottom front of the tent is in a
straight line, from corner to
corner.
Rev.D 4.09
D
A
BE
F
fig 11


Produkt Specifikationer

Mærke: Eureka
Kategori: Telt
Model: Pine Lodge

Har du brug for hjælp?

Hvis du har brug for hjælp til Eureka Pine Lodge stil et spørgsmål nedenfor, og andre brugere vil svare dig




Telt Eureka Manualer

Telt Manualer

Nyeste Telt Manualer

De Waard

De Waard Zeester Manual

7 Oktober 2024
SereneLife

SereneLife SLTET30 Manual

1 Oktober 2024
Calima

Calima 46074 Manual

1 Oktober 2024
SereneLife

SereneLife SLPTSR107 Manual

30 September 2024
Vaude

Vaude Badawi Long 6 Manual

29 September 2024
De Waard

De Waard Stormmeeuw Manual

25 September 2024
Vrijbuiter

Vrijbuiter Stormvogel Manual

22 September 2024
Crivit

Crivit IAN 86428 Manual

20 September 2024