EXSYS EX-1300 Manual


Læs nedenfor 📖 manual på dansk for EXSYS EX-1300 (2 sider) i kategorien Kabler til pc'er og periferiudstyr. Denne guide var nyttig for 21 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Because the designs of computers are different, only general installation instructions are
given. Please refer your computer’s reference manual whenever in doubt.
1. Connect the USB cable to the USB B Connector of the module.
2. Plug the included power supply into the 5V Connector (optional).
3. Now connect the other end from the USB cable ( A-Plug) to the A-Connector at
your PC.
HARDWARE INSTALLATION :
6 5
EXEXEX---130013001300 EnglishEnglishEnglish EXEXEX---130013001300 EnglishEnglishEnglish
1
Das USB zu Parallel Modul ist zur Umsetzung von USB auf eine Parallele Schnitt-
stelle für den Anschluss von High Speed Parallelen Peripherie Geräten (z.B.
Drucker, Scanner usw.) geeignet. Das Modul ist Hot Plug & Play hig. Für die
Einstellungen der I/O Adressen und Interrupts sind keine Jumper und Einstellun-
gen notwendig. Sie werden vom System und beim Installieren des Betriebssys-
tems automatisch vorgenommen.
BESCHREIBUNG & TECHNISCHE DATEN :
AUFBAU :
Kompatibilität: USB 1.1 & 2.0 Anschluss
Betriebssysteme: WIN 98/ME/2000/XP/Server 2003/Vista/MAC
Anschlüsse: 36 Pin Centronics Buchse, 1 x USB A-Stecker
Lieferumfang: 1 x USB zu Parallel Modul, Anleitung, CD
Zertifikate: / FCC / RoHS / WEEE DE97424562
DRIVER INSTALLATION :
JUMPER EINSTELLUNG & ANSCHLÜSSE:
CLEANING :
For cleaning please use only a dry fluffless cloth and remove the dirt with gently pressu-
re. In the area of the connectors please make sure that no fibres from the cloth remain
in the connectors. Attention! Never use a moist or wet cloth for cleaning!
Windows 98 ME 2000 XP Server 2000 and Server 2003 (32-bit):
Windows will recognize a new “USB Parallel Device“ and open the hardware assistant.
Please choose manual installation and put the driver CD into your CD-Rom drive ( as
sample D:). Now enter the Path "D:\USB_to_IO\ USB_to_Parallel\WIN98_ME_2K_XP”
into the box for the Path/Source and click at >next/continue<. Now Windows will
search for the drivers in the specified directory. Follow the hardware assistant and finish
the installation. If Windows recognizes other new devices repeat the above described
steps. Attention! Restart Windows in any case after installing the drivers.
CHECK THE INSTALLED DRIVER:
Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the window
that opens select >Device Manager<. Under ”Ports (COM and LPT)“ you should find
one more new „USB Parallel Port„ as sample If you see this or similar entries (LPT3).
the module is installed correctly.
CHANGE PORT NUMBER:
If you like to change the port number for example LPT 2 to LPT 3, open the >Device Man-
ager< click at >LPT2<, >Settings< and then >Advance<. There you can choose between
LPT 1 up to 3.
INSTALL THE PERIPHERAL DEVICE:
Now you can install a parallel peripheral device to the module.
Windows XP and Server 2003 (64-bit):
Windows will recognize a new “USB Parallel Device“ and open the hardware assistant.
Windows will recognize the device automatically and install it. Follow the hardware
assistant and finish the installation. Restart Windows in any case after installing the
drivers.
CHECK THE INSTALLED DRIVER:
Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the window
that opens select >Device Manager<. And open „Universal Serial Bus Controller“
you should find the entry „USB Parallel Converter“. If you see this or similar entries
the module is installed correctly.
INSTALL THE PRINTER DEVICE:
To install a printer please proceed with the following steps:
Click at >Start< >Settings< >Printer and Fax devices< >Add printer< > < >Next Local
printer<. Select one of the new ports “USB 001 or USB 002 (Virtual printer port for
USB)” to install a new printer to the module. Now follow the Hardware assistant to
complete the Installation of your printer.
DRIVER INSTALLATION :
Windows Vista (32 & 64-bit):
Windows will recognize a new “USB Parallel Device“ and open the hardware assistant.
Windows will recognize the device automatically and install it. Follow the hardware
assistant and finish the installation. Restart Windows in any case after installing the
drivers.
CHECK THE INSTALLED DRIVER:
Click at the “Start Windows Logo< then enter “compmgmt.msc“ at the “search box”
and select it on the top under “Programs”. In the window that opens select >Device
Manager<. And open „USB Controller“ there you should find the entry „USB Parallel
Converter“. If you see this or similar entries the module is installed correctly.
INSTALL THE PRINTER DEVICE:
To install a printer please proceed with the following steps:
Click at >Start< > < >Settings Printer and Fax devices< >Add printer< > < >Next Local
printer<. Select one of the new ports “USB 001 or USB 002 (Virtual printer port for
USB)” to install a new printer to the module. Now follow the Hardware assistant to
complete the Installation of your printer.
MAC:
There are no MAC OS drivers for this product but the modules are supported by the
most versions of MAC OS. Because each individual version of MAC OS is different,
sadly we cant provide a installation instruction. Please refer to the installation manual for
IO ports from your MAC OS version !
JUMPER SETTING & CONNECTORS:
USB B-Connector:
USB 2.0 B-Connector:
Pin Signal Pin Signal
1 VCC 4 GND
2 DATA-
3 DATA+
Attention!
Never plug in with
force or in wrong
direction.
36 Pin Centronics
Parallel Stecker
USB 1.1
A-Stecker
Pin Signal Pin Signal Pin Signal
1 STROBE 13 SELECT 25 GND
2 DATA 0 14 AUTO FEED 26 GND
3 DATA 1 15 N/C 27 GND
4 DATA 2 16 0 V 28 GND
5 DATA 3 17 Chassis GND 29 GND
6 DATA 4 18 +5V PULLUP 30 Reset GND
7 DATA 5 19 GND 31 RESET
8 DATA 6 20 GND 32 FAULT
9 DATA 7 21 GND 33 0 V
Parallel Centronics 36 Pin :
10 ACKNOWL 22 GND 34 N/C
11 BUSY 23 GND 35 +5V DC
12 PAPER OUT 24 GND 36 SLCT IN
Centronics 36F:
BedienungsanleitungBedienungsanleitung
Vers. 3.0 / 12.02.08


Produkt Specifikationer

Mærke: EXSYS
Kategori: Kabler til pc&#39;er og periferiudstyr
Model: EX-1300
Vægt: 170 g
Produktfarve: Grå
Kabellængde: 1.8 m
Stik 1: USB 1.1
Stik 2: IEEE1284

Har du brug for hjælp?

Hvis du har brug for hjælp til EXSYS EX-1300 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Kabler til pc'er og periferiudstyr EXSYS Manualer

EXSYS

EXSYS EX-1303 Manual

11 September 2024
EXSYS

EXSYS EX-1311-2 Manual

29 August 2024
EXSYS

EXSYS EX-1300 Manual

29 August 2024
EXSYS

EXSYS EX-2311-2F Manual

29 August 2024
EXSYS

EXSYS EX-1322 Manual

29 August 2024
EXSYS

EXSYS EX-K1552V Manual

29 August 2024
EXSYS

EXSYS EX-47995 Manual

29 August 2024
EXSYS

EXSYS EX-49010 Manual

29 August 2024
EXSYS

EXSYS EX-1309-9 Manual

29 August 2024
EXSYS

EXSYS EX-1401 Manual

29 August 2024

Kabler til pc'er og periferiudstyr Manualer

Nyeste Kabler til pc'er og periferiudstyr Manualer