EXSYS EX-1345 Manual

EXSYS Kabler til pc'er og periferiudstyr EX-1345

Læs nedenfor 📖 manual på dansk for EXSYS EX-1345 (2 sider) i kategorien Kabler til pc'er og periferiudstyr. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Because the designs of computers are diﬀerent, only general installation instructions are

given. Please refer your computer’s reference manual whenever in doubt.

1. Connect the USB cable to the USB B Connector of the module.

2. Now connect the other end from the USB cable ( A-Plug) to the A-Connector at

your PC.

HARDWARE INSTALLATION :

6 5

EXEXEX-

-134513451345

EnglishEnglishEnglish

EXEXEX-

-134513451345

EnglishEnglishEnglish

Die EX-1345 USB zu Parallel ist zur Umsetzung von USB auf Parallele Schnitt-

stelle für den Anschluss von Drucker geeignet. Wird im Betriebssystem Windows

als „USB Drucker Unterstützung“ installiert. Die EX-1345 ist Hot Plug & Play

fähig. Für die Einstellungen der I/O Adressen und Interrupts sind keine Jumper

und Einstellungen notwendig. Sie werden vom System und beim Installieren des

Betriebssystems automatisch vorgenommen.

BESCHREIBUNG & TECHNISCHE DATEN :

AUFBAU :

Kompatibilität: USB 1.1 & 2.0 Anschluss

Betriebssysteme: WIN XP/Server 2003/Vista/Win 7/MAC

Anschlüsse: 25 Pin Sub-D Buchse, 1 x USB B-Buchse

Lieferumfang: 1 x EX-1345, Anleitung, CD, USB Kabel

Zertiﬁkate:

/ FCC / RoHS / WEEE DE97424562

DRIVER INSTALLATION :

JUMPER EINSTELLUNG & ANSCHLÜSSE :

Windows XP and Server 2003 (32 & 64-bit):

Windows will recognize a new and open the hardware assistant. “USB Parallel Device“

Windows will recognize the device automatically and install it. Follow the hardware

assistant and ﬁnish the installation. Restart Windows in any case after installing the

drivers.

CHECK THE INSTALLED DRIVER:

Click at <> < then enter and click at . In the windows Start Run “compmgmt.msc“ >OK<

that open select And open>Device Manager<. „Universal Serial Bus Controller“ you

should ﬁnd the entry If you see this or similar entries the „USB Parallel Converter“.

module is installed correctly.

INSTALL THE PRINTER DEVICE:

To install a printer please proceed with the following steps:

Click at > < > < > < > < >Start Settings Printer and Fax devices Add printer Next< >Local

printer “USB 001 or USB 002 (Virtual printer port for <. Select one of the new ports

USB)” to install a new printer to the module. Now follow the Hardware assistant to

complete the Installation of your printer.

Windows Vista and Win 7 (32 & 64-bit):

Windows will recognize a new and open the hardware assistant. “USB Parallel Device“

Windows will recognize the device automatically and install it. Follow the hardware

assistant and ﬁnish the installation. Restart Windows in any case after installing the

drivers.

CHECK THE INSTALLED DRIVER:

Click at the < then enter at the “Start Windows Logo “compmgmt.msc“ “search box”

and select it on the top under . In the windows that open select “Programs” >Device

Manager<. „USB Controller“ „USB Parallel And open there you should ﬁnd the entry

Converter“. If you see this or similar entries the module is installed correctly.

INSTALL THE PRINTER DEVICE:

To install a printer please proceed with the following steps:

Click at > < > < > < > < >Start Settings Printer and Fax devices Add printer Next< >Local

printer “USB 001 or USB 002 (Virtual printer port for <. Select one of the new ports

USB)” to install a new printer to the module. Now follow the Hardware assistant to

complete the Installation of your printer.

BedienungsanleitungBedienungsanleitung

Vers. 1.0 / 19.09.12

JUMPER SETTING & CONNECTORS :

25 Pin Buchse

Parallel Port

Pin Signal Pin Signal Pin Signal

1 STROBE 10 ACKNOWLEDGE 19 GROUND

2 DATA 0 11 BUSY 20 GROUND

3 DATA 1 12 PAPER EMPTY 21 GROUND

4 DATA 2 13 SELECT 22 GROUND

5 DATA 3 14 AUTO FEED 23 GROUND

6 DATA 4 15 ERROR 24 GROUND

7 DATA 5 16 INIT 25 GROUND

8 DATA 6 17 SELECT INPUT

9 DATA 7 18 GROUND

Parallel 25 Pin Buchse :

DB 25F:

USB B-Connector:

USB 2.0 B-Connector:

Pin Signal Pin Signal

1 VCC 4 GND

2 DATA-

3 DATA+

Attention!

Never plug in with

force or in wrong

direction.

Produkt Specifikationer

Mærke:	EXSYS
Kategori:	Kabler til pc'er og periferiudstyr
Model:	EX-1345
Bredde:	75 mm
Dybde:	60 mm
Højde:	25 mm
Vægt:	360 g
Produktfarve:	Beige
Opbevaringstemperatur (T-T):	-40 - 75 °C
Driftstemperatur (T-T):	0 - 55 °C
Kabler inkluderet:	USB
Certificering:	CE, FCC, RoHS
Kabellængde:	1.8 m
Kompatible operativsystemer:	- Windows 98SE / ME/ XP/ Vista/Win7/ 8\r\n- Server(2000 & 2003)
Plug and play:	Ja
Stik 1:	USB 1.0 / 2.0 B
Stik 2:	25-pin D-SUB
Stik 1 køn:	Hunstik
Stik 2 køn:	Hunstik
USB påkrævet:	Ja
Relativ luftfugtighed:	5 - 95 %