Fibaro FGSS-101 Manual

Fibaro Røgdetektor FGSS-101

Læs nedenfor 📖 manual på dansk for Fibaro FGSS-101 (2 sider) i kategorien Røgdetektor. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

ENG

OPERATING MANUAL

SMOKE SENSOR

FGSS-001 v2.1 - v2.3

The Fibaro Smoke Sensor is a universal, optical Z-Wave smoke sensor. The

device can be hard wired (12 or 24 VDC) or battery operated (battery life 3 years*).

Smoke detection is signaled through siren and LED diode blinking. Additionally, the

smoke sensor signal can be sent to an alarm system or fire alarm system hub,

through a NC (normally closed) contact terminals.

The optical sensor detects smoke at an early stage of fire, often before flames

appear and temperature starts to rise significantly. Moreover the device has a

built-in temperature sensor, which can also trigger the alarm once the specified

temperatute threshold is exceeded.

The Fibaro Smoke Sensor is designed to be placed on a wall or ceiling. LED

indicator signals fire, operating mode and used to see if device is within the

Z-Wave network. The smoke sensor is designed to operate in confined spaces,

under normal conditions (lacking smoke, dust, condensed water vapor).

SPECIFICATIONS

Power Supply:

Battery Type:

Power Consumption

(at VDC operation):

Output terminals maximum current

carrying capacity

(SMOKE NC, TAMP NC):

Maximum voltage at output terminals

(SMOKE NC, TAMP NC):

EU standards compliance:

Radio protocol:

Radio frequency:

Range:

Operational Temperature:

Measured Temperature Range:

Temperature Measuring Accuracy:

Dimensions (Diameter x Height):

12 - 24 VDC

CR123A

0,4W

25mA

24V (AC or DC)

EMC 2004/108/EC

R&TTE 199/5/WE

Z - Wave

868,4 MHz EU;

908,4 MHz US;

921,4 MHz ANZ;

869,2 MHz RU;

up to 50m outdoors

up to 30m indoors

(depending on terrain and building

structure)

0 - 40oC

-20 to 100oC

0,5oC (within 0oC - 40oC range)

65 x 28 mm

TECHNICAL INFORMATION

• Compatible with any Z-Wave Controller.

• May be connected to any alarm or fire prevention system by hard wiring NC

output

• Extremely easy installation - simply install it in location prone to fire.

• Battery or VDC powered.

• Built-in tamper switch.

• Alarm is signaled by sound and LED diode.

• Fire detection through air temperature measuring.

• Can trigger alarm just by exceeding temperature threshold.

• 3 levels of sensors sensitivity.

• Automatic efficiency test performed every 5 seconds.

• Built-in “black box” allows the device to report and record smoke and temperature

readouts.

I. Z-WAVE NETWORK INCLUSION

There are two ways to include a Fibaro Smoke Sensor into the Z-Wave network:

1) Automatically, using the auto inclusion function (available in constant current

powering mode), or

2) Manually - using the B-button (option available in both powering modes -

hard wired or battery powered).

Including a Fibaro Smoke Sensor into the Z-Wave network in auto inclusion mode:

1) Make sure the Fibaro Smoke Sensor’s power is disconnected and/or the battery

is removed prior to auto inclusion and located within the direct range of Z-Wave

controller.

2) Set the main controller into the learning mode

(see main controller’s operating manual).

3) Connect the power to the sensor to include it into the Z-Wave network.

4) Fibaro Smoke Sensor will be detected and included into the Z-Wave network.

III. SENSOR INSTALLATION

Fig. 1 - Fibaro Smoke Sensor top view.

BATTERY TIPS

Fibaro Smoke Sensor’s battery life is approximately 3 years when

on optimum settings. The current battery level is displayed in the

Home Center 2 interface. Red battery icon means that battery

needs replacement. In order to avoid triggering tamper alarm while

replacing the battery, 2-nd association group’s associations must

be deleted, and Sensor’s parameters’ configuration set to default.

In addition, the device itself, apart from the main controller,

monitors the battery level and a low battery is signaled with a

yellow blinking LED and an intermittent sound alarm (interval set

in parameter 87). The Fibaro Smoke Sensor can signal a low

battery level for approximately 30 days.

IV. POWERING MODES

There are two powering modes for the Fibaro Smoke Sensor. By default it’s

current, after connecting a 12 / 24 VDC power source to +12/24 and GND

terminals (see diagram #3). Powering mode configuration is carried out

automatically, while sensor is being included into the Z-Wave network. When

battery powered, a Fibaro Smoke Sensor communicates with the Z-Wave network

main controller periodically. Smoke detection is sent immediately. Configuration

parameters and association settings are sent periodically at specified wake up

intervals, or at a manual wake up (triple click B-button). In DC powering mode,

configuration and association parameters are sent when necessary, and

additionally the smoke sensor serves as a Z-Wave signal repeater.

Switching to a constant current powering mode:

1) Exclude a sensor from the Z-Wave network.

2) Disconnect the battery,

3) Install the constant power connecting terminal, observing the diagram #3.

4) Connect the constant current power to the power terminal (12 / 24 VDC) to +12

and GND terminals observing wiring diagram #3.

5) Include Fibaro Smoke Sensor into the Z-Wave network.

NOTE

1. It’s not possible to power the device from a battery and VDC

power source simultaneously. When using a VDC power souce it’s

recommended to use another kind of power back up.

2. Home Center 2 checks the battery level once a day.

NOTE

Read this manual before attempting to install the device. Failure to

observe recommendations included in this manual may be

dangerous or cause a violation of the law. The manufacturer, Fibar

Group Sp. z o.o., will not be held responsible for any loss or

damage resulting from not following the instructions of operating

manual.

NOTE

Work within local code height requirements for installation of the

Fibaro Smoke Sensor. Take special precautions during installation

and use tools and equipment in perfect working order. It’s

recommended to observe ladders, lifts and other obstacles.

NOTE

Maintenance inspections should be perfomed regularly, by a

trained staff member. Fibar Group Sp. z o.o. recommends the

functional and visual checks to be performed at least once a

month. Functional check, includes self test (described below) and

triggering smoke detection.

NOTE

When handled carelessly or used in non-specified environment

conditions, the device may not function properly. It’s highly

recommended to take all safety precautions to ensure safety and

property protection.

NOTE

Depending on the Smoke Sensors internal conditions (e.g. battery

discharge, device failure, etc.) and installation conditions, this

device may not be 100% accurate. This device can significanlty

increase the probability of fire detection. Smoke Sensors must be

tested regularly according to this operating manual and local code.

Ventilation systems, chimneys and potentially dangerous devices

that can cause a fire should be regularly inspected as well.

NOTE

In case the device is not detected, include it manually (as

described below) or reset the sensor and repeat the procedure

above.

In order to turn off the auto inclusion function, press the B-button once after the

power source has been connected to the Fibaro Smoke Sensor.

Manual Fibaro Smoke Sensor inclusion:

1) Connect the power source to the Fibaro Smoke Detctor and/or install the battery.

Make sure the device is located within direct range of the Z-Wave controller.

2) Set the main controller into the learn mode (see main controller’s operating

manual).

3) Quickly, triple click the B-button, located on Fibaro Smoke Sensor’s enclosure.

4) Fibaro Smoke Sensor will be detected and included in the Z-Wave network.

II. EXCLUDING FIBARO SMOKE SENSOR FROM THE Z-WAVE NETWORK

1) Make sure the sensor is connected to power source (battery and/or hard wired).

2) Set the main controller into the learn mode (see main controller’s operating

manual)

3) Quickly, triple click the B-button, located on Fibaro Smoke Sensor’s enclosure.

5) Screw the Fibaro Smoke Sensor into the cover.

6) If the sensor is already included in the Z-Wave network, wake it up by triple

clicking the B-button..

7) Test Fibaro Smoke Sensor’s operation by using a dedicated optical smoke

sensor diagnostic tool.

8) Test the Z-Wave network assuring the device is within range.

NOTE

It’s recommended to install the sensor on the ceiling or upper

portion of wall at least 40 cm (2 feet) from corners and other

objects. Particular attention should be paid to any adjacent objects

or devices which can impede smoke’s access to the sensor. It’s

recommended to install Fibaro Smoke Sensor in all rooms prone

to fire, and in between such rooms as well.

INSTALLATION NOTES:

1) When choosing location of smoke sensor, make sure the alarm sound can be

easily audible in other rooms in the building.

2) It’s recommended to install the sensor in already decorated, painted rooms.

3) It’s recommended to install the sensor at least 1,5m from air conditioners.

4) Do not install the sensor in insolated places. Keep at least 0,5m distance from

light sources.

5) Do not install the sensor in places prone to draughts.

6) Do not install the sensor in places with high water vapor condensation, e.g.

above stoves, ovens, kettles, etc.

Diagram 1 - DC Power adapter connection.

Diagram 2 - Alarm system hub connection.

DIAGRAMS DESCRIPTION:

+12V - constant power supply terminal, 12/24VDC

-GND - ground terminal

SMOKE NC - potential free, smoke sensor connecting terminals

(for wired systems)

TAMP NC - potential free, tamper connecting terminals (for wired systems).

V. SMOKE DETECTION

Fibaro Smoke Sensor responds to the physical presence of smoke. Smoke

presence is required for the device to react. Fibaro Smoke Sensor performs a self

test every 5 seconds (see section VII) and checks for smoke presence. When

smoke is detected, the sensor checks 3 more times, at 1 second interval to see,

whether the smoke is actually present. Once the smoke presence is confirmed,

Fibaro Smoke Sensor triggers an alarm.

Smoke alarm is signaled by sending an appropriate alarm frame to devices and the

Z-Wave controller, opening NC contact, and also by a constant sound signal and

LED diode blinking red. Once the smoke alarm has ceased, the sensor checks 3

times, at 1 second interval, whether the smoke has actually disappeared before

getting back to normal operation, i.e. performing a self test each 5 seconds and

checking for presence of smoke.

NOTE

As described in section V, the Fibaro Smoke Sensor checks for

smoke presence every 5 seconds. In addition, the device checks

for damage and tests the Z-Wave network communication at each

wake up interval (see section VIII).

NOTE

Fibaro Smoke Sensor is a multiple use device, however, for

greater safety, it’s recommended to replace the device with a new

one after a fire occurance.

VI. DETECTING FIRE THROUGH TEMPERATURE ALARM

Apart from detecting smoke presence, Fibaro Smoke Sensor can detect fire by

recording a rapid temperature rise. Temperature alarm threshold is user defined

(parameter 81). Temperature alarm is signaled by the blinking red LED signaling

diode blinking red and an intermittent sound signal.

NOTE

Parameter 81 value is set to 54ºC by default. Any modification of

this parameter may cause the Fibaro Smoke Sensor not to work

within the valid safety regulations of your country.

VII. MALFUNCTION DETECTION

The Fibaro Smoke Sensor can automatically detect a malfunction. As described in

section V, the Fibaro Smoke Sensor performs a self test every 5 seconds. If a malfunction

is detected (e.g. damaged smoke chamber) an intermittent sound alarm will start, LED

diode will blink red and alarm will be sent to the Z-Wave network controller and

associated devices.

Once a malfunction has been detected, it’s recommended to:

• check the power source (replace battery or check VDC adapter’s voltage),

• check whether the Smoke Sensor is exposed to direct light.

If a malfunction is continually reported, it’s recommended to replace a the Fibaro Smoke

Sensor with new one.

Self test may be triggered manually:

1) Make sure the device is being powered.

2) Press and hold the B-button untill the LED glows white and short alarm sounds.

3) Keep holding the B-button for an additional 3 seconds from the first beep to check the

smoke chamber operation.

LED indicator colour changing to green and beep mean the positive result. If the LED

indicator changes its colour to red, the sensor is malfunctioning.

NOTE

Any service or repair must be carried out by the manufacturer.

VIII. DETECTING LACK OF Z-WAVE RANGE

When included in the Z-Wave network, Fibaro Smoke Sensor tests the network

communication. The Z-Wave network communication test is performed in both hard wired

and battery powering modes during every temperature report. By default, once the

ambient temperature changes by 2ºC, according to parameters 10 and 12 settings. In

addition, in battery mode, the Z-Wave network communication test is performed at device

polling. In constant power mode, the Z-Wave network communication test is performed in

time intervals defined by parameter 80 settings. Lack of the Z-Wave network communica-

tion is signaled by an intermittent alarm sound and LED blinking pink.

Once a Fibaro Smoke Sensor has reported no Z-Wave network communication, it’s

recommended to wake up the device by triple clicking the B-button. If it doesn’t stop the

alarm, Z-Wave networks operation and the main controllers operation need to be verified.

The Fibaro Smoke Sensor will cancel the Z-Wave network communication alarm once it

communicates with the network after manual or automatic wake up.

NOTE

It’s not recommended to deactivate the Z-Wave network communication

test.

IX. SENSOR’S SENSITIVITY LEVEL CONFIGURATION

There are 3 sensitivity levels of the optical smoke detector used in Fibaro Smoke Sensor.

By default, the detector is set to the middle sensitivity level. Sensitivity level depends on

the parameter 82 settings.

X. RESETTING THE FIBARO SMOKE SENSOR

The Fibaro Smoke Sensor reset erases the EPROM memory, including all information on

the Z-Wave network and the main controller.

Fibaro Smoke Sensor reset procedure:

1) Make sure the device has the power connected.

2) Press and hold the B-button for 3 seconds. LED will glow white.

3) Short signal will sound.

4) Release the B-button.

5) Wait until the LED glows yellow, signaling entering the 4th menu level.

6) Press the B-button briefly to confirm menu level choice.

Successful reset will be confirmed with the LED changing colour to red and fading. At the

same time, short beep will sound, same as at the power connection.

XI. OPERATING THROUGH THE Z-WAVE NETWORK

Fibaro Smoke Sensor has a built in smoke detector and a temperature sensor, which

makes it a multi channel device. In the Home Center 2 menu it will be presented as two

devices, depending on the main controller software version*:

Fig. 2 - Constant current or alarm system hub

connecting terminals installation.

AUX COM Z1 Z2

ALARM

SYTEM HUB

+12/24

GND

SMOKE

TAMP

12/24 VDC

ADAPTER

GND

+12/24

GND

SMOKE

TAMP

NOTE

It’s not recommended to change Fibaro Smoke Sensor’s sensitivity

level.

B - button

and LED indicator

TMP

NOTE

When the self test is triggered manually, the Fibaro Smoke Sensor sends

the command frame to the Z-Wave network controller and to the 1st

Association group devices. After 3 seconds from releasing the B-button,

the alarm cancelling command frame will be sent and the procedure will

be finished.

Installing Fibaro Smoke Sensor

1) Include the device into the Z-Wave network (see p.I). Note the inclusion process

may be performed ONLY in direct range of the main controller.

2) If the sensor is hard wired to power source, drill holes in sensor’s cover. Note the

sensor may be connected to a wired alarm system controller or fire prevention

system.

3) Install the sensor’s cover in desired location.

4) If the sensor is to be VDC powered, connect wires observing diagram # 3. If the

sensor is to be connected to an alarm system or fire prevention system, connect

it observing the diagram # 4.

* Depending on the parameters settings.

Drill holes here

NOTE

Device reset will not remove it from the Z-Wave network main

controller’s memory. Before resetting the device, it must be excluded

from the Z-Wave network.

Produkt Specifikationer

Mærke:	Fibaro
Kategori:	Røgdetektor
Model:	FGSS-101

Har du brug for hjælp?

Hvis du har brug for hjælp til Fibaro FGSS-101 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Røgdetektor Fibaro Manualer

Fibaro Smoke Sensor 2 Manual

14 August 2024

Fibaro FGSD-002 Manual

13 August 2024

Fibaro FGCD-001 Manual

10 August 2024

Fibaro Smoke Sensor FGSD-002-NL-A-v1.01 Manual

8 August 2024

Fibaro FGSS-101 Manual

8 August 2024

Røgdetektor Manualer

Nyeste Røgdetektor Manualer

First Alert HD6135FB Manual

14 Oktober 2024

TFA AirCo2ntrol Life Manual

8 Oktober 2024

Elro FS151021M Manual

8 Oktober 2024

Elro 2001-023 Manual

3 Oktober 2024

FireHawk FHB10 Manual

2 Oktober 2024

Smartwares RM149 1YR Manual

2 Oktober 2024

First Alert SA410 Manual

1 Oktober 2024

König SAS-SA2002 Manual

1 Oktober 2024

FireAngel ST-622 Manual

30 September 2024

Alecto SA-49/1 Manual

29 September 2024