FLIR N233ZD Manual

FLIR Overvågningskamera N233ZD

Læs nedenfor 📖 manual på dansk for FLIR N233ZD (1 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 2 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/1
PACKAGE CONTENTS:
1x CD
1x Micro PT IP Camera
Quick Start Guides
Installing the Camera
A
2.1MP HD IP Micro PT Camera
N233ZD
Quick Connection Guide
B
• Use an appropriate low voltage power cable to prevent fire or electrical
shock.
• Make sure to install the camera in an area that can support the camera
weight.
• There are no user serviceable parts inside the camera. Please do not
disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning material. Please use
a lint free micro-fiber cloth to clean the lens cover.
• Camera is rated for outdoor use (IP66), but is not intended for submersion
in water.
Safety PrecautionsWeights & Dimensions
C
Installing the Camera Connecting the Camera (continued)
0.6lbs / 0.3kg
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Notice
1 2 3
1x Allen Key
1. Ethernet Port: Connect the camera to an NVR or a router or
switch on your network using Cat5e or better Ethernet cable
(not included). PoE Class 3 supported.
2. Power Input: If not using PoE, connect the camera to a 12V
DC power source (300mA or higher required).
Remove the vinyl film from the camera lens once installation is
complete.
Information in this document is subject to change
without notice. As our products are subject to continuous
improvement, FLIR Systems, Inc. and our subsidiaries reserve
the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE © 2014 FLIR Systems, Inc. All rights reserved.
www.flirsecurity.com/pro
For support, visit
Latest software and manuals available on
www.flirsecurity.com/pro
N233ZD_QCG_EN_R1
Weight
2.3” /
58mm
Connect cables as shown in the section “Connecting the Camera”.
D
Align the 3 notches on the side of the dome camera with the
3 corresponding pegs on the mounting plate. Push the camera
gently into the mounting plate until you hear a ‘click‘.
3x Mounting Screws
Use the included mounting template to mark holes for the
mounting screws and camera cable.
Drill holes for the mounting screws and camera cable.
NOTE: Use the included drywall anchors if installing on a drywall
surface.
Align the metal mounting plate so that the 3 screw holes in the
plate line up with the 3 holes drilled in the wall.
Attach the flat side of the mounting plate to the surface using the
included mounting screws (3x).
1
2
3x Drywall Anchors
Inserting the microSD Card
Resetting the Camera
5.1” /
130mm
ERemove the M2x5 screw from the side of the camera using the
included Allen key.
Drywall anchors (3x)
Mounting surface
Mounting plate
Mounting screws (3x)
M2x5 screw
F
H
I
J
NOTE: The pegs and notches only align one way. Do not force
the camera to fit into the mounting plate.
Notches (x3)
Pegs (x3)
Re-insert the M2x5 screw removed in Step E. Tighten firmly using
the included Allen key.
G
Ensure the camera is grounded with the
pre-inserted M2x5 screw.
A
B
Separate the camera from the mounting plate if needed.
Remove the 2 screws from the compartment
cover using a Phillips screwdriver (not included).
C
D
Slide the microSD carriage cover to open, then
lift upward.
Place a microSD card (not included) into the
carriage with the metal contacts facing down.
OPEN
LOCK
A
B
C
Separate the camera from the mounting plate
if needed.
Remove the 2 screws from the compartment
cover using a Phillips screwdriver (not included).
Press and hold the reset button for 4 seconds.
OPEN
LOCK
Close and lock the carriage cover. Replace the
compartment cover on the camera base.
E
Reset button
Replace the compartment cover on the
camera base.
D
1x Mounting Plate 1x Mounting Template
GND port

Produkt Specifikationer

Mærke: FLIR
Kategori: Overvågningskamera
Model: N233ZD

Har du brug for hjælp?

Hvis du har brug for hjælp til FLIR N233ZD stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera FLIR Manualer

FLIR

FLIR M42046 Manual

13 September 2024
FLIR

FLIR PT-117 Manual

8 September 2024
FLIR

FLIR Saros DH-390 Manual

4 September 2024
FLIR

FLIR T4350BN Manual

2 September 2024
FLIR

FLIR M500 Manual

25 August 2024
FLIR

FLIR Cloud N233BE Manual

25 August 2024
FLIR

FLIR Pinnacle DPV74TLUX Manual

19 August 2024
FLIR

FLIR G300 pt Manual

18 August 2024
FLIR

FLIR F-304 Manual

15 August 2024
FLIR

FLIR FB-393-O Manual

13 August 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Sony

Sony SNC-DH160 Manual

16 November 2024
Bresser

Bresser DL-30MP Manual

15 November 2024
D-Link

D-Link DCS-6500LHV2 Manual

14 November 2024
D-Link

D-Link DCS-2803KT Manual

13 November 2024
D-Link

D-Link DCS-2804KT Manual

13 November 2024
D-Link

D-Link DCS-931L Manual

13 November 2024
D-Link

D-Link DCS-6100LHV2 Manual

13 November 2024
Philips

Philips Series 3000 HSP3800 Manual

13 November 2024
Emos

Emos H4060 Manual

13 November 2024
Philips

Philips Series 3000 HSP3500 Manual

13 November 2024