Focal FDP 6.900 V2 Manual

Focal Modtager FDP 6.900 V2

Læs nedenfor 📖 manual på dansk for Focal FDP 6.900 V2 (8 sider) i kategorien Modtager. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/8
1
POWER PER CHANNEL
6 x 150w RMS into 4 ohms @ 1% THD
6 x 200w RMS into 2 ohms @ 1% THD
4 x 150w RMS into 4 ohms + 1 x 500w RMS into 4 ohms (Ch 5+6 Bridged) @ 1% THD
4 x 200w RMS into 2 ohms + 1 x 500w RMS into 4 ohms (Ch 5+6 Bridged) @ 1% THD
Do NOT bridge into 2 ohms.
All power ratings are at 14.4v DC.
INPUTS SWITCH
2 = Use input 1+2 and route them to channels 3+4 and 5+6
4 = Use input 1+2 and 3+4
1+2 and 3+4 are attenuated by -6dB and routed to 5+6.
This allows constant bass loudness when you fade between 1+2 and 3+4.
6 = Use all six inputs.
CHANNELS 1 & 2 CROSSOVER CONFIGURATION
Flat: Full Range Signal. No crossover activated.
HP: Activates the High Pass Filter for a midbass or tweeter.
Copy 3 & 4: Copies the signals and filters from channels 3 & 4 to channels 1 & 2. Use this mode when you need
a band pass filter on all four channels. Recommended when bridging channels 1, 2, 3, 4.
CHANNELS 3 & 4 CROSSOVER CONFIGURATION
Flat: Full Range Signal. No crossover activated.
HP: Activates the High Pass filter.
LP/BP: Activates the selection of either a Low Pass filter for woofer or a Band Pass filter for midrange.
CHANNELS 5 & 6 CROSSOVER CONFIGURATION
Flat: Full Range Signal. No crossover activated.
HP: Activates the High Pass filter.
LP/BP: Activates the selection of either a Low Pass filter for woofer or a Band Pass filter for midrange.
Sub Mode: Inputs 5+6 are mixed to mono for bridge mono operation. Crossover slopes become 24dB.
The subwoofer remote volume control is activated. There is a clip distortion light on the remote volume control.
If you see this light is on, reduce volume until the light goes out so that you do not damage your speaker.
AUTOMATIC POWER TURN ON/OFF
1. The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio
connected to the REM amplifier terminal.
2. If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn
on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not
necessary.
FDP 6.900 V2: 6-CHANNEL AMPLIFIER
OPERATION / CONFIGURATION MANUAL


Produkt Specifikationer

Mærke: Focal
Kategori: Modtager
Model: FDP 6.900 V2

Har du brug for hjælp?

Hvis du har brug for hjælp til Focal FDP 6.900 V2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Modtager Focal Manualer

Focal

Focal FDP 1.900V2 Manual

28 August 2024
Focal

Focal FPX 1.100 Manual

21 August 2024
Focal

Focal FPS 4160 Manual

21 August 2024
Focal

Focal FDP 6.900 Manual

20 August 2024
Focal

Focal FDP 6.900 V2 Manual

19 August 2024
Focal

Focal FDS 2.350 Manual

19 August 2024
Focal

Focal FPS 2160 Manual

19 August 2024
Focal

Focal FDP 4.600 Manual

19 August 2024
Focal

Focal FDP 1.2000 Manual

19 August 2024
Focal

Focal FDS 1.350 Manual

19 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Onkyo

Onkyo TX-RZ30 Manual

23 November 2024
Sony

Sony STR-DE185 Manual

23 November 2024
QSC

QSC PowerLight 9.0 Manual

20 November 2024
Ashly

Ashly FX-125.4 Manual

20 November 2024
Harman Kardon

Harman Kardon CA5250 Manual

19 November 2024
Esoteric

Esoteric F-05 Manual

19 November 2024
Konig & Meyer

Konig & Meyer 28075 Manual

18 November 2024
IFi Audio

IFi Audio ZEN CAN 3 Manual

18 November 2024