Furrion F52INS-PS-AM Manual


Læs nedenfor 📖 manual på dansk for Furrion F52INS-PS-AM (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
50Amp 125V/250V Shore Power Inlet / Installation Instructions
FURRION 50 ampères 125V/250V / Installation de votre che
WARNING
ELECTRICAL SHOCK
AND FIRE HAZARD!
To prevent the risk of electrocu-
tion or fi re, ensure the inlet and
connecting cables are NOT con-
nected to a power source during
installation! Use only 6 AWG or
above cable with this product.
Using a smaller AWG cable will
result in overheating and possible
Fire Hazard.
Cable color scheme for 125/250V 4
core cables:
Black = Y - Live/Hot Cable
Red = X - Live/Hot Cable
White = W - Neutral Cable
Green = G - Ground Cable (8 AWG)
Installation
1. Select a suitable mounting position
for the power inlet. Mark a basic
outline for the inlet using the sup-
plied sealing gasket. (Fig. A)
Fig. A
2. Cut out the center circular hole
using a 2¾ ” hole saw and drill the
four mounting holes using a 1/8”
drill bit. (Fig. B)
Fig. B
3. Open the inlet cover and remove
the two screws holding the rear
housing. (Fig. C & Fig. D) Remove
the rear housing from the inlet.
(Fig. E)
Fig. C
Fig. D
Fig. E
4. Remove the strain relief insert
and the strain relief ring from the
inside of the rear housing. (Fig. F)
Fig. F
Strain Relief
Insert Strain Relief
Ring
5. Rotate counterclockwise to remove
the strain relief nut and the cable
clip. (Fig. G)
Fig. G
Cable Clip
6. Strip off 1 ” of the outer insula-½
tion layer of the cable and 5/8” of
colored insulation from the ends of
the three conductor cables. (Fig. H)
Fig. H
Romex
Wire Stranded
Core Wire
7. If you are using a Romex Wire,,
thread the cable through the sealing
gasket, strain relief nut, cable clip
and the rear housing. (Fig. I)
Fig. I
Required for Stranded Core Wire
only - If you are using a Stranded
Core Wire, thread the cable through
the sealing gasket, strain relief nut,
strain relief insert, strain relief ring
and the rear housing. (Fig. J)
Fig. J
8. Connect the colored wires to the
corresponding lettered holes on
the back of the inlet and tighten
the terminal screws to 22-25 in-lbs
torque. (Fig. K & Fig. L)
Black
Red
White
Green
Fig. K
22-25 in-lbs
Fig. L
9. Replace the inlet rear housing and
secure with the two screws. Rotate
the rear cap clockwise to fi x the
cables. (Fig. M)
Fig. M
10. Fit the power inlet into the open-
ing and secure with four mounting
screws (not included). (Fig. N)
Housing Screw Size
Stainless KA3.5 x 30
Plastic PA3.5 x 30
Fig. N
Model: F52INS-SS/F52INS-PS/ F52INS-
GS/ F52INS-BS/ F52INR-PS/F52INS-BSN


Produkt Specifikationer

Mærke: Furrion
Kategori: Ikke kategoriseret
Model: F52INS-PS-AM

Har du brug for hjælp?

Hvis du har brug for hjælp til Furrion F52INS-PS-AM stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Furrion Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024