Fusion MS-CRGBWRC Manual


Læs nedenfor 📖 manual på dansk for Fusion MS-CRGBWRC (12 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/12
®
 %+! &! , ,             ! ’ ) -!   ) ( -+) &
 ( , -+.  -%) ( ,
 ’ *) +- ( -   "! -0  ( ") +’  -%) (
       
Failure to follow these warnings and cautions could result in
personal injury, damage to the vessel, or poor product
performance.
See the guide in the Important Safety and Product Information
stereo box for product warnings and other important information.
This device must be installed according to these instructions.
Disconnect the vessel's power supply before beginning to install
this product.
       
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
N O T I C E
When drilling or cutting, always check what is on the opposite
side of the surface to avoid damaging the vessel.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation,
contact Fusion® Product Support.
 . **&%! ,   (   ) ) &,   ! ! !
2-conductor 22 AWG (0.33 mm2) wire to connect the remote
control receiver to the power source
6-conductor 22 AWG (0.33 mm2) wire (or equivalent
combination of 2- to 4-conductor wire) to connect the receiver
to the LED speakers
Cable ties or adhesive for mounting the receiver
4 gauge (3 mm) countersunk stainless-steel screws for
mounting the remote cradle (optional)
3 mm flat screwdriver
Wire cutters
Drill and drill bits for mounting the remote cradle (optional)
 ) . ( -%( #  (    ) ( ( !  -%) (   ) ( , % !+ -%) ( ,
When selecting a location for the remote control receiver and
making the wiring connections, observe these considerations.
The receiver housing is not weather proof, and you must
install the receiver in a location that is not exposed to the
elements.
You can connect a single receiver to up to 10 LED speakers
with RGB, cool white, and warm white functionality (5 pair).
You must use an additional receiver and remote control (sold
separately) to connect to additional LED speakers.
You cannot use a single remote control with more than one
receiver.
 ) ( ( ! -%( # -$!   ! ’ ) -!   ) ( -+) &  !  ! %/ ! +
You can connect up to 10 (5 pair) of CRGBW LED speakers to
one remote control receiver.
 Route a power wire (not included) from a 12 Vdc power
source to the location of the receiver .
 Install the included 7.5 A fuse on the power wire.
 Route 6-conductor wire or equivalent (not included) from
the receiver to the speakers you want to control, joining the
wire where needed to connect up to 4 speakers.
      To avoid interference, you must not route the LED
wires near and parallel to any RCA, power, or speaker audio
cables. You should also avoid routing this cable near any
other electronic cabling on the vessel.
 Connect the 6-conductor wire or equivalent to the CRGBW
connectors on the speakers according to the installation
instructions provided with the speakers.
 Loosen the wire terminal screws on the bottom of the
receiver using a 3 mm flat screwdriver.
 Connect the power and RGB speaker wires to the wire
terminals on the sides of the receiver.
 ! --! + ) (  +!  ! %/ ! + &  ! &  %+!   ) &) + ) + ". (  -%) (
INPUT +12V DC (left
side)
12 Vdc negative (-)
INPUT -12V DC (left
side)
12 Vdc positive (+)
V+ (BLACK) (right side) CRGBW 12 Vdc positive (+) (common)
wire
      Two V+ connectors are provided
on the right side for convenience. You
should connect the common wire from
the speakers to only one of these
connectors.
WARM WHITE
(YELLOW)
CRGBW warm white wire
COOL WHITE
(TURQUOISE)
CRGBW cool white wire
V+ (BLACK) (right side) CRGBW 12 Vdc positive (+) (common)
wire
      Two V+ connectors are provided
on the right side for convenience. You
should connect the common wire from
the speakers to only one of these
connectors.
RED CRGBW red wire
GREEN CRGBW green wire
BLUE CRGBW blue wire
 Tighten the wire terminal screws on the bottom of the
receiver.
 Secure the receiver to the mounting location using cable ties
or adhesive (not included).
 ( , - &&%( # -$!  !’ ) -!   ) ( -+) &  + &!
You can install the included remote cradle to store the remote
when not in use. Mounting hardware for the cradle is not
included.
N O T I C E
Because the remote control is not weatherproof, you must install
the cradle in a location that is not exposed to the elements.
 Using the cradle as a template, mark the two pilot holes.
 Remove the cradle from the mounting surface and drill the
pilot holes.
GUID-80736249-84A1-4457-B3FC-9231AA6112DC v1August 2020


Produkt Specifikationer

Mærke: Fusion
Kategori: Ikke kategoriseret
Model: MS-CRGBWRC

Har du brug for hjælp?

Hvis du har brug for hjælp til Fusion MS-CRGBWRC stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Fusion Manualer

Fusion

Fusion CAB000541 Manual

19 August 2024
Fusion

Fusion BT-100 Manual

15 August 2024
Fusion

Fusion MS-RGBRC Manual

14 August 2024
Fusion

Fusion MS-FR402 Manual

13 August 2024
Fusion

Fusion WS-PKTD Manual

12 August 2024
Fusion

Fusion MS-CRGBWRC Manual

12 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024