Galaxy Audio PA6BT Manual


Læs nedenfor 📖 manual på dansk for Galaxy Audio PA6BT (2 sider) i kategorien Højttaler. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
G
G
G
GGA
A
A
AAL
L
L
LL A
A
A
AA X
X
X
XX Y
Y
Y
YY A
A
A
A AU
U
U
UU
D
D
D
DDI
I
I
IIO
O
O
OO Quick Start Guide
PA6BT
Full Range Powered Personal Monitor
Included Components
1. PA6BT x1
3. MSA-1 Stand Adapter x1
2. IEC Power Cable x1
Setup
2.1. 4.
4. Quick Start Guide x1
3.
Connect power cable to PA6BT, connect
other end to a power outlet.
2
Choose the input needed and for what
channel(s) needed:
XLR/1/4" Combo Jack for mic, or
balanced/unbalanced line level.
1/8" for stereo from a media player etc.
3
For a balanced mic signal, plug the XLR
male end of the cable into the XLR/1/4"
Combo Input on the PA6BT. For strong
signals, engage the -20dB Pad Switch to
prevent distortion.
4
For Balanced or Unbalanced Line Level,
plug the 1/4" cable into the XLR/1/4"
Combo Jack on the PA6BT.
5
Connect a female XLR to the Thru
output to feed the channel’s XLR input
to another device.
1
For a stereo signal from an MP3 player,
attach 1/8" stereo cable into the Channel
2 1/8" input.
6
Flip the power switch on.
3
Level controls: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
4 5 62
EQ controls - Low/Mid/Hi: To increase the
low, mid, and high frequencies, turn the
appropriate tone control clockwise. To
decrease, turn counter-clockwise.
1
Ensure that both channels and/or the
Bluetooth controls have their levels ®
lowered by turning counter-clockwise.
Stand Mounting (Optional)
1
Attach the MSA-1 to the mic stand, then
Lift the PA6BT over the stand, align it up
with the hole.
2
Bring the PA6BT down onto the stand
gently until secure.
Operation
The Pre Out provides a Line Level mix
of all three channels.
7
Reduce Input Levels if the Clip LED turns
on. Max. level is reached when the yellow
“Comp” light flashes at peak levels. If the
light is on constantly, turn the levels down
to avoid damage to
the PA6BT.
Using Bluetooth - Press the Bluetooth® ®
button. The Bluetooth LED will flash for®
15 seconds. Locate the PA6BT on your
device and select to pair. If pairing fails,
turn Bluetooth off and try again. The®
button also acts as a Stop/Play/Pause.
Powering the unit off will disconnect.
GAL A X Y AUDIO Quick Start Guide
PA6BT
Full Range Powered P ersonal Monitor
Included Components
1. PA6BT x1
3. MSA-1 Stand Adapter x1
2. IEC Power Cable x1
Setup
2.1. 4.
4. Quick Start Guide x1
3.
Connect power cable to PA6BT, connect
other end to a power outlet.
2
Choose the input needed and for what
channel(s) needed:
XLR/1/4" Combo Jack for mi c, or
balanced/unbalanced line level.
1/8" for stereo from a media player etc.
3
For a balanced mic signal, plug the XLR
male end of the cable into the XLR/1/4"
Combo Input on the PA6BT. For strong
signals, engage the -20dB Pad Switch to
prevent distortion.
4
For Balanced or Unbalanced Line Level,
plug the 1/4" cable into the XLR/1/4"
Combo Jack on the PA6BT.
5
Connect a female XLR to the Thru
output to feed the channel’s XLR input
to another device.
1
For a stereo signal from an MP3 player,
attach 1/8" stereo cable into the Channel
2 1/8" input.
6
Flip the power switch on.
3
Level controls: turn clockwis e to raise the
level. Turn counter-clockw ise to lower
the level.
4 5 62
EQ controls - Low/Mi d/Hi: To increase the
low, mi d, and high frequencies, turn the
appropriate tone control clockwi se. To
decrease, turn counter-clock wise.
1
Ensure that both channels and/or the
Bluetooth controls have their levels ®
lowered by turning counter-clockwi se.
Stand Mounting (Optio nal )
1
Attach the MSA-1 to the mic stand, then
Lift the PA6BT over the stand, align it up
with the hole.
2
Bring the PA6BT down onto the stand
gently until secure.
Operation
The Pre Out provides a Line Level mix
of all three channels.
7
Reduce Input Levels if the Clip LED turns
on. Max. level is reached when the yellow
“Com p” light flashes at peak levels. If the
light is on constantly, turn the levels down
to avoid damage to
the PA6BT.
Using Bluetooth - Press the Bluetooth® ®
button. The Bluetooth LED will flash for®
15 seconds. Locate the PA6BT on your
device and select to pair. If pairing fails,
turn Bluetooth off and try again. The®
button also acts as a Stop/Play/Pause.
Powering the unit off will disconnect.


Produkt Specifikationer

Mærke: Galaxy Audio
Kategori: Højttaler
Model: PA6BT

Har du brug for hjælp?

Hvis du har brug for hjælp til Galaxy Audio PA6BT stil et spørgsmål nedenfor, og andre brugere vil svare dig




Højttaler Galaxy Audio Manualer

Højttaler Manualer

Nyeste Højttaler Manualer