Gel Blaster Surge Manual


Læs nedenfor 📖 manual på dansk for Gel Blaster Surge (2 sider) i kategorien Legetøj. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
WARNING:
Do not change the coloration and markings to make it look more like a firearm.
That is dangerous and may be a crime. Buyer and user have the duty to obey
all laws about the use and ownership of this toy. Adult supervision required.
Misuse or careless use may cause serious injury, especially to the eye.
Eye protection must be used by the user and any person within range. May be
dangerous up to 100 feet. Read owner’s manual before using. Recommended
for users 9 years or older, and may be more appropriate for users 12 years
and older.
CHANGE BARREL
BARREL TOOLBARREL
TO REMOVE, ROTATE
COUNTER-CLOCKWISE
SINGLE OFF FULL-AUTO
BLASTER MODE SWITCH
STEP 1 - HYDRATE YOUR GELLETS™ !! IMPORTANT !!
Gellets™ must be submerged in water for at least two hours to fully expand to size. They also need to have
plenty of water to absorb (this is very important) - you’ll know there was plenty of water if after 2 hours the Gellets
are still submerged in the water. Failing to completely hydrate Gellets will cause your Gel Blaster® to seem crappy.
Note: Make sure that the Gellets are prepared in an adequate sized container. Gellets will expand 10 times
their original size. Store hydrated Gellets away from the elements and direct sunlight. Gellets last
indefinitely when dehydrated and up to three months when submerged in water.
STEP 2 - CHARGE YOUR BLASTER
The Charging LED light (on the bottom) will show solid red when charging, when fully charged,
the light will turn green. While in use, the light will flash red on the side and the bottom of the
blaster to indicate a low battery.
STEP 3 - FILL YOUR HOPPER
Fill your hopper with hydrated Gellets, make sure all water is drained from
the hopper before installing on your blaster.
STEP 4 - INSTALL HOPPER ONTO BLASTER
Screw the hopper into the Starfire feedneck. Then slide the feedneck onto
the top rail of the SURGE with the arrow pointing forward.
IMPORTANT - Make sure you slide the feedneck all the way forward until you feel
and hear a “click”. Failing to do so will cause your Gel Blaster SURGE to misfire.
STEP 5 -OPTIONAL: INTERCHANGEABLE BARRELS
Your Gel Blaster currently comes with the Standard Barrel pre-installed (175fps).
To remove the barrel, use the Barrel Tool provided to unscrew the barrel. You can then
install your orange Reduced Velocity Barrel (100fps) for a lighter blasting experience.
IMPORTANT - DO NOT OVERTIGHTEN YOUR BARREL!
STEP 6 - PROTECT YOUR EYES!
Put on your provided eye protection when using your Gel Blaster SURGE. Make sure that others within
firing distance are wearing eye protection too! Do not shoot at people not wearing proper eye-wear.
STEP 7 – POWER ON AND HAVE A BLAST!
Switch between Single and Full-Auto with the Blaster Mode Switch.
CLEAR
HOPPER
STARFIRE
FEEDNECK
HOPPER INSTALL
STATUS LIGHTS
USB-C CHARGING PORT
BATTERY
INDICATORS
SOAK FOR
2 HOURS
1
2
TIP
FINS
NOTCH
SIDE UP
TIP
FINS
NOTCH
SIDE UP
2
1
SWAP FINS & TIPS INSTALLREMOVE
GELLETS
HYDRATION
VIDEO
ONE GALLON OF WATER
MAKES 10,000 GELLETS™!
WARNING: The Gel Blaster is
not intended to get wet. Don't
submerge your Gel Blaster in
water, and make sure your Gellets are fully
strained of excess water. This will protect
the battery and circuitry within.


Produkt Specifikationer

Mærke: Gel Blaster
Kategori: Legetøj
Model: Surge

Har du brug for hjælp?

Hvis du har brug for hjælp til Gel Blaster Surge stil et spørgsmål nedenfor, og andre brugere vil svare dig




Legetøj Gel Blaster Manualer

Legetøj Manualer

Nyeste Legetøj Manualer