GVM 7SM Manual
GVM
Flashenhed
7SM
Læs nedenfor 📖 manual på dansk for GVM 7SM (2 sider) i kategorien Flashenhed. Denne guide var nyttig for 53 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
1 5 6 7 8 9 10
GVM-7SM
1142 3
OLED display
Switch button
RGB LED
lamp beads
Charging port
This light has CCT and RGB two light-emitting surfaces, and both sides cannot
be lighted up at the same time. One side is lighted according to the mode and scene.
Dual color
temperature LED
lamp beads
Compound knob
12 13
CCT light-emitting
surfaces:
RGB light-emitting
surfaces:
3You can choose to ins tal l the su pplied hot s hoe brack et or small head
accordin g to you r needs. The installation steps are as follows:
4Loosen the angle locking knob of the small pan-tilt, you can adjust the
angle of the small pan-tilt, and tighten the angle locking knob after
adjusting the angle.
Switch button
Charging port
OLED display
Bracket mounting
screw port 2You can choose to install an external diffuser according to your needs.
The installation steps are as follows:
Hot shoe bracket installation steps
5Install it on the camera as shown below.
Hot shoe bracket installation steps
Small head installation steps
12
34
1
2
3
4
OLED display: Display current power, mode, parameters,
scenes, etc.
Charging line interface
Power switch
Compound knob:
Light indicator
does not light
up.
Ch e c k i f the b at t e ry i s o ut o f
po w e r. Use the light after charging it.
APP can't
connect / cannot
be controlled
Check if the Bluetooth connection
is successful
Normal steps:
Color cannot be
adjusted
Check whether the color purity
SAT value is too low or 0; the
color purity value is 100, the
color difference is the most
obvious.
Increase the color purity SAT
value in HSI mode
When the light
is turned on,
the display
and lights are
not on.
Check if the light is "turned off"
by mobile APP.
Sw itc h the "O N/ OFF " b ut ton
on th e li ght a gai n.
FacebookGVM Official
website
Download APP
Web: www.gvmled.com
B&H Email: bh@gvmled.com
GVM Email: support@gvmled.com
Amazon Email: amazonsupport@gvmled.com
Warehouse Add: 4301 N Delaware ave, unit D. PHILADELPHIA, PA19137, USA
Welcome to “GVM-7SM”. This product is specially designed for senior
photography enthusiasts. The product is suitable for live / outdoor / studio
photography, and also for YouTube video shooting. The main features of the
product are:
PRODUCT
INTRODUCTION
①
②
Step-less adjustable RGB color and dual color temperature feature,
brightness / color temperature / hue / color purity can be controlled at will,
color range 2700K ~ 6500K, with 124 LED lamp beads, which is helpful to
restore and enrich the color of objects and provide you with natural and
vivid shooting effect.
App intelligent control system, which can be controlled by your intelligent
mobile device.
③With an OLED screen display and a stable system, and comes with a soft
light board to make the light softer, allowing you to easily and casually
shoot the desired results.
We believe that once using our product correctly, you can make huge progress
when shooting. Before using the product, you are strongly recommended to
read the instructions below carefully.
④Small size and light weight, and b uilt-in battery power supply. It is very
portable f or outdoor shooting.
PRODUCT PARAMETER
1.
PRECAUTIONS
①Please use the matching power adapter or lithium battery with the same
specification to power the product. Do not use power adapter with
different output voltage parameters.
The product is not waterproof, please use it in rainproof environment.②
The product is not anti-corrosion, therefore do not let the product touch
any corrosive liquid.
③
When using the product, make sure the product is put firmly and prevent
from falling and damage.
④
If the product will not be used for a long time, please switch off the power
to reduce energy loss.
⑤
DISCLAIMERS
Before using this product, please read the instructions carefully and make sure
use the product correctly. If you don't obey the instructions and warnings, you
maybe cause harm to yourself and the people around, or even damage the product
and other things around.
2. Once you use this product, you are deemed to have read the disclaimer and warning
carefully, understand and acknowledge all the terms and contents of this statement,
and promise to take full responsibility for the use of this product and possible
consequences.
Brand : GVM
Product Name : Double-sided Photography LED Light
Product Type : Photography Fill Light
Product model : GVM-7SM
Product material : Aluminum Alloy + PVC
Lamp beads quantity : 124
Color rendering index : ≥97
Color temperature : 2700K~6500K
Hue : RGB 0 ~360°°
Brightness : 1200lux/0.5m, 600lux/1m
Light adjustment method : Step-less adjustment
Features: Bluetooth APP Connection, High CRI LED Beads,
OLED Screen, Multiple Scene Modes
Power : 7W
Voltage : DC5V
Power supply mode : DC5V Input & Battery
Battery capacity : 3.7V / 3000mAh
Product weight : 0.25KG
Product size ( mm ) : 80*106*42
Cooling : Natural heat dissipation
Commodity origin : Huizhou , China
C O N T E N T S
⑤Can simulate 8 kinds of scene lights: Lightning, Police Car, Candlelight,
TV, Bad LED Bulb, Party, Disco, Paparazzi.
14
PRODUCT
STRUCTURE ANALYSIS
1Fully charge the lamp firstly (charger current>2A), and the screen can
display the battery level after power on.
INSTALLATION
METHOD
Small head installation steps
DESCRIPTION OF
PRODUCT CONTROL KEYS
Long Press-Switch mode: CCT / HSI / EFFECT
Short Press-Switch the adjustable parameters in current mode
Turn-Adjust the currently selected parameter
Display current power, mode, parameters, scene, etc.
① OLED display:：
FUNCTION & INSTRUCTION
FOR USING
② Two methods of controlling light
Control the ligh t through compound kno b;
Control the light through APP;
③ Modes
Long press composite knob to switch modes: CCT / HSI / EFFECT;
CCT : Dual color temperature mode, adjustable brightness and color
temperature.
HSI : RGB color light mode, adjustable brightness, hue and color purity.
EFFECT : Scene light mode. You can select scenes and adjust the parameters
of the current scene. There are 8 scenes: Lightning, Police Car, Candle, TV,
Bad Bulb, Party, Disco, Paparazzi
CCT :
HSI :
EFFECT :
④ Adjust brightness (BRG): range 0%~100%
The brightness can be adjusted in all modes. Short press the composite
knob to select the brightness (BRG) → turn the knob to adjust the
brightness.
Connect to APP and adjust brightness through APP.
⑤ Adjust color temperature (CCT): range 2700K~6500K
Long press the composite knob to switch to CCT mode → short press the
composite knob to select color temperature (CCT) → turn the knob to
adjust the color temperature.
Connect to APP and adjust the color temperature through APP.
⑥ Adjust HUE: range 0 ~ 360° °
Long press the composite knob to switch to HSI mode → short press the
composite knob to select hue (HUE) → turn the knob to adjust the hue.
Connect to APP, adjust hue through APP.
⑦ Adjust SAT: range 0%~100%
Long press the composite knob to switch to HSI mode → short press the
composite knob to select color purity (SAT) → turn the knob to adjust
color purity.
Connect to APP, adjust hue through APP.
⑧ Adjustment scene effect
Long press the composite knob to switch to EFFECT mode → short press
the composite knob to select FX → turn the knob to select the scene →
short press the composite knob to select the parameter to be adjusted
→ turn the knob to adjust the parameter.
Connect to APP, select and adjust scene light through APP.
Scan the QR code on the back of the manual to download the APP
APP CONNECTION AND
APP CONTROL
Turn on the video light and open the “GVM_LED” application software on the
phone ( The phone needs to turn on Bluetooth and GPS), then enter the
Bluetooth's search interface → Find the Bluetooth named “BT_LED” and
connect → Waiting for connection → After connection successfully, it will
automatically enter APP control interface. At this time, the video light have
been connected and you can control the light through APP.
You can save 6 custom light effects in “My Scene s”. After setting the light
effect parameters → click the “ ” icon in the right co rner → pop up to
the “Save Current Scen es” small wind ow→ click “OK”. This light effect
can be fo und in “My Scenes” at this t ime .
Color temper ature
control interface
RGB contr ol
interface
Scene light
control interface
Save light effect
interface
USE AND
PRESERVATION
Clean：Please do not clean during charging. And use wet cloth rather than any detergent
or soluble liquid, avoiding damaging the surface layer.
Repairing：If there is fault or performance degradation, do not unpack the shell by
yourself, avoiding damage the machine and lose the right of maintenance. When there
is a fault, do not hesitate to contact us, and we will do our best to deal with the problem.
Accessories：Please use the accessories provided by manufacturer and approved
ones, in order to maximize the performance.
Guarantee：Do does not modify the product, or you will lose the right of maintenance.
Repairing：
Accessories：
Guarantee：
Power：Ensure that the power supply is within the required range of use, too high or too
low will affect the work. The built-in battery is not removable.
Do not put the product in a highly humid, strong electromagnetic field, direct
sunlight, high-temperature environment. If not use the product for a long
time, disconnect the power.
Clean：
Power：
Phenomenon Check the product Troubleshooting
① Turn on Bluetooth and GPS
on the mobile phone;
② Open the APP, search and
connect to the Bluetooth
BT_LED
SIMPIE FAULTS
AND TROUBLESHOOTING
1
Small Head
User Manual
N a me
Q u an t i ty
N o te s
1
1
1
1
GVM-
7SM
Photography
Lights
1
PACKING
LIST
Charging
Cable
External
Diffuser
Hot Shoe
Bracket
Product introduction Page 1- ---------------------------------------- --
Disclaimers Page 2- ----------------------------------------------------- --
Precautions Page 2- ---------------------------------------------------- --
Product parameter Page 3- ------------------------------------------ --
Product structure analysis Page 4- --------------------------------- --
Installation method Page 5~7- -------------------------------------- --
Description of product control keys Page 8- -------------------- --
Function & instruction for using Page 9~10- --------------------- --
APP connection and APP control Page 11- -------------------- --
Use and preservation Page 12- -------------------------------------- --
Simpie faults and troubleshooting Page 13- -------------------- --
Packing list Page 14- ---------------------------------------------------- --
Produkt Specifikationer
| Mærke: | GVM |
| Kategori: | Flashenhed |
| Model: | 7SM |
Har du brug for hjælp?
Hvis du har brug for hjælp til GVM 7SM stil et spørgsmål nedenfor, og andre brugere vil svare dig
Flashenhed GVM Manualer
27 Februar 2024
19 Januar 2024
25 Juni 2023
18 November 2022
Flashenhed Manualer
- Flashenhed Sony
- Flashenhed Canon
- Flashenhed Panasonic
- Flashenhed Fujifilm
- Flashenhed Nikon
- Flashenhed Olympus
- Flashenhed Leica
- Flashenhed Sigma
- Flashenhed Ricoh
- Flashenhed Godox
- Flashenhed Konica-Minolta
- Flashenhed Ikan
- Flashenhed Genaray
- Flashenhed Petzl
- Flashenhed Hähnel
- Flashenhed Vivitar
- Flashenhed Manfrotto
- Flashenhed Triopo
- Flashenhed Neewer
- Flashenhed Bolt
- Flashenhed Nissin
- Flashenhed Lume Cube
- Flashenhed Aputure
- Flashenhed Vello
- Flashenhed Sunpak
Nyeste Flashenhed Manualer
17 November 2024
22 Oktober 2024
12 Oktober 2024
12 Oktober 2024
6 Oktober 2024
19 Juli 2024
19 Juli 2024
19 Juli 2024
19 Juli 2024
19 Juli 2024