Hager 85346188 Manual

Hager Ikke kategoriseret 85346188

Læs nedenfor 📖 manual på dansk for Hager 85346188 (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

KNX radio motion detector comfort

1.1 m quicklink

Order no. 8534 51 ..

KNX radio motion detector comfort

2.2 m quicklink

Order no. 8534 61 ..

Operating and assembly

instructions

Berker GmbH & Co. KG

Zum Gunterstal

66440 Blieskastel, Germany

Tel.: + 49 6842 945 0

Fax: + 49 6842 945 4625

e-mail: info@berker.de

www.berker.com

04/2022

6LE005217D

KNX radio motion detector comfort

1.1 m quicklink

KNX radio motion detector comfort

2.2 m quicklink

Safety instructions

Electrical equipment must only be installed

and assembled by a qualied electrician in ac-

cordance with the relevant installation stand-

ards, regulations, directives and safety and ac-

cident prevention directives of the country.

Failure to comply with these instructions may

result in damage to the device, re or other

hazards.

The radio transmission is not suitable for safe-

ty or alarm applications.

Due to its detection behaviour the device is not

suitable for use in burglary detection or alarm

systems.

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

(3)

(5)

(6)

(4)

(2) (1)

Fig. 1: Design and layout of the device

(1) Insert

(see "Accessories", not in scope of delivery)

(2) Frame (not included)

(3) Application module

(4) Motion detector design cover

(5) Module retaining screw

(not for Berker R.1/R.3/R.8)

(6) Interface between insert/application module

Function

System information

This device is a product of the quicklink system, in

which installation devices communicate via radio

signals.

quicklink stands for a configuration mode, in which

the function-related connection between trans-

mitters and receivers is set on the device through

buttons and displays without further tools.

All devices configurable by quicklink can be oper-

ated together in one system.

► See configuration instructions.

This device complies with EU Directive 2014/53/EU.

The declaration of conformity and further system

information can be accessed at hager.com.

The device may be operated in all EU and EFTA

states (excluding Switzerland and Liechtenstein).

Correct use

- Automatic switching of lighting depending on

heat motion and ambient brightness

- Application module for switch insert, dimmer

insert or power supply for KNX radio applica-

tion module

- The device has been designed for smaller ap-

plications, in which a maximum of 20 devices

are allocated

- Only suitable for use in indoor areas with no

drip and no spray of water

Product characteristics

- quicklink functions to extend the detection ar-

ea, scenes, control circuits

► See conguration instructions

- Remote control via quicklink transmitter

- Integrated button for selecting operating modes

and special functions

- Lockable integrated button

- The operating modes Automatic, Permanent

ON, Permanent OFF can be selected

- Display operating mode via LED

- Potentiometer for setting the response bright-

ness and detection sensitivity

- Adjustable detection angle for adapting the

detection area

- Additional adjustment of the response bright-

ness via Teach-In function

- Party function

- Presence simulation

- Optional extension unit operation via installa-

tion button

Automatic mode

The motion detector detects heat motion caused

by people, animals, or objects.

On switch insert and dimmer insert with factory

setting:

- The light will be switched on for a xed delay

time of 3 minutes if movements are detected in

the detection area and the set brightness

threshold is undershot. Each additional move-

ment in the detection area restarts the delay

time.

- The light will be switched o󰀨 after 3 minutes if

no additional movements are detected.

On dimmer insert configured with time function

(see configuration instructions):

- The light will be switched on for the delay time,

if movements are detected in the detection ar-

ea and the set brightness threshold is under-

shot. Each additional movement in the detec-

tion area restarts the delay time.

- After the delay time elapses, the lighting will be

dimmed to 50% of the switch-on brightness

level and will remain at this brightness level for

30 s (switch-o󰀨 pre-warning). Any motion de-

tected during the switch-o󰀨 pre-warning re-

starts the delay time and restores the switch-on

brightness level.

- The light will be switched o󰀨 if no motion is

detected any longer in the detection area and

the set delay time and the switch-o󰀨 pre-warn-

ing have elapsed.

Performance after mains breakdown/return of

mains supply

- Mains breakdown shorter than 0.2 s:

The function is not impaired.

- Mains breakdown longer than 0.2 s:

There is no function during the mains break-

down. The current conguration is saved in

non-volatile memory.

- Return of mains supply:

The application module executes an initialisa-

tion for approx. 5 s, during which the lighting

will be switched on. Motion detection starts

thereafter. If no motion is detected during the

rst 5 s, the lighting is switched o󰀨. The saved

conguration is loaded from memory. During

this period, local operation via the button or

extension unit can be used.

Operation

Operating concept

(8)

(7)

Fig. 2: Display and operating elements

(7) Button

(8) Status LED

Operation is executed by pushing the button (7)

on the motion detector:

- A short press of the button switches the operat-

ing modes. The operating mode is displayed

via the status LED behind the optics cover of

the motion detector.

- Keeping the button pressed activates special

functions. Selection of the special functions is

supported by the LED display (Fig. 3).

Selecting the operating mode

Briefly press the button repeatedly until the

desired operating mode is selected.

The status LED indicates the selected operat-

ing mode (see Table 1).

Switching the operating mode nishes the party

function or presence simulation, if these func-

tions were previously active.

Disabling/enabling operating mode selection

via button

Keep the button pressed for more than 15

seconds, until the status LED is flashing green

(Fig. 3).

Selection of the operating mode via the button

is disabled.

or if the button is locked:

Keep the button pressed for more than 15

seconds, until the status LED is flashing green

(Fig. 3).

The operating mode can be selected via the

button again.

Switching on the lighting via push-button ex-

tension unit or changing the switch-on bright-

ness level

Optionally, the lighting can be switched on via a

mechanical push-button extension unit (Table 2).

For extension unit operation, the lighting is

switched on independently of the set bright-

ness threshold.

When using the dimmer inserts, the last set

brightness level will be saved as the switch-on

brightness level.

Activating/interrupting party function

The party function switches the lighting on for 2

hours. During this time, no extension unit or radio

commands are executed.

Keep the button pressed for more than 5 sec-

onds, until the status LED flashes red (Fig. 3).

The lighting is switched on for 2 hours. During

this time the status LED is flashing red. When

the 2 hours have elapsed, the motion detector

switches to the operating mode.Auto

Briefly press the button.

The party function is interrupted and the motion

detector reverts to the operating mode.Auto

Activating/deactivating the presence simula-

tion

During operation, the motion detector counts the

motion detections in one full hour and saves the

result. With active presence simulation at the

beginning of the hour with the most detections

saved, the light will be switched on for the duration

of the delay time, even no motion is detected.

During the presence simulation, presence de-

tection, extension unit and radio commands will

continue to be executed normally.

Keep the button pressed for more than 20

seconds, until the status LED slowly flashes

red (Figure 3).

The presence simulation is active. During this

time the status LED lights orange. The motion

detector switches the lighting on at the saved

time.

Briefly press the button.

The presence simulation will be deactivated,

the motion detector reverts to the operat-Auto

ing mode.

Settings

Setting response brightness via Teach-In

function

The response brightness is the brightness value

saved in the motion detector; when this value

is undershot the motion detector switches the

connected load if movements are detected. Via

Teach-In function the current ambient bright-

ness is saved as the response brightness.

The load is switched off.

Keep the button pressed for more than 10

seconds, until the status LED flashes orange

(Fig. 3).

The motion detector detects the current

ambient brightness and saves it as response

brightness.

Setting of the response brightness via

Teach-In function and via the brightness po-

tentiometer has the same priority. Teach-In

overwrites the response brightness set on

the brightness potentiometer. If the setting is

made again via the potentiometer , the

Teach-In gure will be overwritten.

Setting the load

If the switching performance is not satisfactory

after commissioning when using the motion de-

tector on universal switch inserts and universal

touch dimmers, a load setting must be carried

out.



A load setting is required each time the load

is changed.

Switch off load.

Keep the button pressed for more than

25 seconds, until the status LED is slowly

flashing orange.

Release push-button.

The connected load flashes once. The

device is in selection mode.

If no further actions are performed within the

next 10 seconds, the dimmer switches to

normal operation.

Briefly press the bottom button repeatedly to

activate the desired setting mode.

► See Table 3a / 3b



Information for electricians:

For the version labelling of the ush-mount-

ed insert, see packaging label or sticker on

the back of the housing.

Function

Party function

Teach-In

Keylock

Presence

simulation

Load setting

mode1)

LED display

Hold time

operation

button

> 5 s >10 s > 15 s > 20 s > 25 s

1) Only on universal switch insert and universal dimmer insert

Fig. 3: Selection of special functions and LED display

LED display

Operating mode

Description

Auto

Motion and brightness-dependent switching on/switching o󰀨

of the load

Green

Permanent ON

Load is permanently switched-on/switched-o󰀨.

Extension unit signals, as well as radio signals, will not be

evaluated

Red

Permanent OFF

Table 1: Display of operating modes

Dimming status

Operation

button

Performance of the insert

Motion detector applied on switch insert

OFF

Short press

Load is switched on for the set delay time

Short press

Extension of switch-on time by the set delay time

Motion detector applied on push-button dimmer comfort 1gang

OFF

Short press

Load is switched on to the switch-on brightness level for the set

delay time

Short press

Extension of switch-on time by the set delay time at the same

brightness

OFF

Long press

Load is switched on to switch-on brightness-level, subsequent

dimming in the opposite direction of the last dimming process.

Thereafter the load remains switched on for the delay time

Long press

Changes the current brightness. Dimming takes place in the op-

posite direction of the last dimming operation until maximum or

minimum brightness. Subsequently the load remains switched

on at the set brightness for the set delay time.

Table 2: Operation via push-button extension unit

Produkt Specifikationer

Mærke:	Hager
Kategori:	Ikke kategoriseret
Model:	85346188

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager 85346188 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Hager Manualer

Hager JF300CF Manual

22 November 2024

Hager EC801250CT Manual

22 November 2024

Hager NCN110A Manual

11 Oktober 2024

Hager JK108BSH Manual

4 Oktober 2024

Hager VML406AH Manual

3 Oktober 2024

Hager JK116BA3 Manual

3 Oktober 2024

Hager JKD188TM Manual

27 September 2024

Hager JK104BF Manual

22 September 2024

Hager JG27BR Manual

22 September 2024

Hager TXA606B Manual

18 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer VP-8X8 Manual

25 November 2024

Kramer PT-2C Manual

25 November 2024

Lazer Bob+ Manual

25 November 2024

Dometic DPS 80 Manual

25 November 2024

Kramer 102MX Manual

25 November 2024

Kramer FC-18 Manual

25 November 2024

Kramer DSP-62-UC Manual

25 November 2024

Kramer KC-BRAINware-25 Manual

25 November 2024

Kramer KC-BRAINware-50 Manual

25 November 2024

Tiger SKF-H101 Manual

25 November 2024