Hager 85648188 Manual

Hager Ikke kategoriseret 85648188

Læs nedenfor 📖 manual på dansk for Hager 85648188 (3 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 15 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

KNX radio button 1gang quicklink

KNX radio button 2gang quicklink

KNX radio button 4gang quicklink

Safety instructions

Electrical equipment must only be installed and

assembled by a qualiﬁ ed electrician in accord-

ance with the relevant installation standards,

regulations, directives and safety and accident

prevention directives of the country.

Failure to comply with these instructions may re-

sult in damage to the device, ﬁ re or other haz-

ards.

The radio transmission is not suitable for safety

or alarm applications.

These instructions are an integral component of

the product and must be retained by the end user.

Design and layout of the device

(1)

(2)

(3)

(4)

(5)

(6)

(7)

Fig. 1: Design and layout of the device

(1) Insert (see "Accessories", not in

scope of delivery)

(2) Frame (not included)

(3) Application module 1, 2 or 4gang

(4) Module retaining screw

(not for Berker R.1/R.3/R.8)

(5) Design cover button 1gang

(6) 2gang button or 4gang button design cover

(7) Interface between insert/application module

Function

System information

This device is a product of the quicklink system, in

which installation devices communicate via radio

signals.

quicklink stands for a conﬁ guration mode, in which

the function-related connection between transmitters

and receivers is set on the device through buttons

and displays without further tools.

All devices conﬁ gurable by quicklink can be operat-

ed together in one system.

This device complies with EU Directive 2014/53/EU.

The declaration of conformity and further system

information can be accessed at hager.com.

The device may be operated in all EU and EFTA

states (excluding Switzerland and Liechtenstein).

Correct use

- For operation and remote control on a switch

insert, on a dimmer insert or on a power supply

for KNX radio application modules

- The device has been designed for smaller appli-

cations, in which a maximum of 20 devices are

allocated

- Only suitable for use in indoor areas with no drip

and no spray of water

The quicklink conﬁ guration of the devices must

only be carried out by qualiﬁ ed electricians.

Product characteristics

- Functions for remote control, scenes, control cir-

cuits via radio signals

- LED display of the compatibility of the insert/ap-

plication module

- Saving of switch-on brightness level if operated

on a dimmer insert

- Option for load setting during operation with uni-

versal inserts (see settings)

Operation on a switch insert

Load status Operation button, factory setting Switch insert

OFF Press top or bottom Switch ON load.

ON Press top or bottom Switch OFF load.

Table 1: Operation on a switch insert

Operation on a dimmer insert

Dimming

status

Operation button,

factory setting

Dimmer insert

OFF Short press on top or bottom Switch ON with saved

switch-on brightness level.

ON Short press on top or bottom Switching OFF.

ON Press top and bottom

simultaneously > 5 s

Save brightness as switch-on brightness-level.

As conﬁ rmation, the light switches OFF brieﬂ y

and ON again.

In the delivery condition, the maximum bright-

ness is saved as the switch-on brightness level.

ON/OFF Long press on top Dimming to maximum brightness-level

ON Long press on bottom Dimming to minimum brightness-level

OFF Long press on bottom Switching on with minimum brightness-level

Table 2: Operation on a dimmer insert

Operation via extension unit, push-button, NO contact

Dimming

status

Operation

push-button

Switch insert Dimmer insert with extension unit input

OFF Press < 0.4 s Switch ON Switch ON with saved switch-on brightness-level

ON Press < 0.4 s Switch OFF Switch oﬀ

ON Press > 0.4 s Switch OFF Dimming to minimum/maximum brightness-level

with alternating direction

OFF Press > 0.4 s Switch ON Dimming from minimum to maximum bright-

ness-level

Table 3: Operation via extension unit, push-button, NO contact

The switch-on brightness-level cannot be saved on an extension unit push-button.

Information for electricians

Overview of the operating elements beneath the

design cover

(9)

(8)

(10)

Figure 2a: Operating elements of the 1gang radio

button

(10)

(11)

(9)

(8)

Figure 2b: Operating elements of the 2 and 4gang

radio button

(8) Press-activation points of the push-button

operation area

(9) button with LEDfct fct

(10) button with LEDcfg cfg

(11) button with LEDfct2 fct2

Installation

Selecting installation location

A minimum distance between the transmitter and

corresponding receiver of about 1 m must be main-

tained.

A minimum distance to electronic devices which emit

high frequency signals such as computers, electronic

transformers or microwave devices of approx. 0.5 m

must be maintained.

Mounting on or close to metal surfaces may cause

impairment of the function.

Take material penetration into account. The range of

the system can be optimised by selecting the best

possible mounting location:

Material Degree of material

penetration

Wood, plaster, plaster-

board, uncoated glass

approx. 90 %

Brick, press boards approx. 70 %

Reinforced concrete,

underﬂ oor heating

approx. 30 %

Metal, metal grids,

aluminium laminates,

coated glass

approx. 10 %

Rain, snow approx. 1 ... 40 %

Table 5: Material penetration

Mounting the device (Figure 1)

The insert is installed (see operating instructions for

the insert).

Attach the application module (3) together with

frame (2) to a suitable insert (1) and establish a

connection between insert and the application

module via the plug-in interface (7).

As soon as voltage is supplied to the button, the

cfg LED (Figure 2, 10) indicates whether the but-

ton and the insert are compatible with each other:

cfg LED

display

Meaning

LED ﬂ ashes

green for

5 s

Compatible

LED ﬂ ashes

red for 5 s

Not compatible

LED ﬂ ashes

orange for

5 s

Compatible, but not conﬁ gured

to each other. For a new con-

ﬁ guration, the application mod-

ule must be reset to the factory

setting.

If required/included use module retaining screw

(4).

Click the design cover (5 or 6) into place on appli-

cation module (3).

If a conﬁ guration needs to be made or settings

need to be changed, only attach the design cover

afterwards.

Insert/application module combinations and

operation in the factory setting

Depending on the insert used, in factory setting

the radio button has the following function for local

operation (Table 6).

KNX radio button

1gang

KNX radio button

2gang

KNX radio button

4gang

Switch insert 1gang -- --

Switch insert 2gang --

Dimmer insert 1gang -- --

Dimmer insert 2gang --

Power supply

Switching (see operation on a switch insert)

Dimming (see operation on a dimmer insert)

-- Not to be combined

Transmitter command freely conﬁ gurable (see Conﬁ guration of radio button as transmitter)

Table 6: Button operation in factory setting

04/2022

6LE005203D

KNX radio button 1gang quicklink

Order no. 8514 51 ..

KNX radio button 2gang quicklink

Order no. 8514 61 ..

KNX radio button 4gang quicklink

Order no. 8564 81 ..

Operating and assembly

instructions

Berker GmbH & Co. KG

Zum Gunterstal

66440 Blieskastel, Germany

Tel.: + 49 6842 945 0

Fax: + 49 6842 945 4625

e-mail: info@berker.de

www.berker.com

Adjusting the load for KNX radio button 1gang or 4gang on a universal switch or dimmer insert

1gang from Version R1.2

Press

bottom

button

Setting mode Duration and conﬁ rmation of the

load setting



The light to conﬁ rm the load ﬂ ashes at 50%

brightness.

Information for use

1 x Load

factory setting

Settings duration: approx. 30 sec.



Load switching/dimming phases may

occur during the automatic settings

process.

The load ﬂ ashes one last time as a con-

ﬁ rmation and then goes out. The device

returns to normal operation.

Factory setting with automatic

load recognition.

If the switching/dimming behav-

iour is dissatisfying after that,

restart the selection mode and

select the suitable option.

2 x LED mode 1

(phase cut-on)

After approx. 5 sec., the load ﬂ ashes twice

as a conﬁ rmation and then goes out. The

device returns to normal operation.

Recommended for lower 230 V

LED loads up to max. 60 W if the

switching/dimming behaviour is

dissatisfying after the automatic

load setting.

3 x LED mode 2

(phase cut-on)

Settings duration: ≤ 50 sec.



Load switching/dimming phases may

occur during the automatic settings

process.

Finally, the load ﬂ ashes three times as a

conﬁ rmation and then goes out. The de-

vice returns to normal operation.

Recommended for higher 230 V

LED loads from 50 W, which can

be operated in the phase cut-on.

Observe manufacturer's data!

4 x Fine setting of

minimum bright-

ness

5 predeﬁ ned minimum brightness levels

for 2.5 sec. each, run through repeatedly

(3 runs).

As soon as the connected load shows

a satisfying minimum brightness,

conﬁ rm by quickly pressing the bottom

button.

After approx. 5 sec., the load ﬂ ashes

four times as a conﬁ rmation and remains

switched on (50% brightness). The device

returns to normal operation.

To optimise the switch-on behav-

iour, or if the load ﬂ ickers in the

lower dimming range, the mini-

mum brightness setting can be

manually adjusted here.

Table 4a

Adjusting the load on a universal switch or dimmer insert up to Version R1.1

Brieﬂ y

press

the

button

Setting mode Conﬁ rmation of the

load setting

Information for use

1 x Load

ﬁ ne-setting

Load ﬂ ashes 1 x after

approx. 30 s and changes

to normal operation

Not suitable for ohmic loads (e.g. incandes-

cent, HV halogen lamps); use factory load

setting.

If the load ﬁ ne-setting does not bring any im-

provement for energy-saving lamps or 230 V

LED lamps, select the energy-saving lamp

ﬁ ne-setting or 230 V LED lamp universal set-

ting.

The load ﬁ ne-setting is not available on 2gang

universal inserts.

2 x Load

factory setting

Load ﬂ ashes 2 x after

approx. 6 s and changes

to normal operation

3 x Energy-saving

lamp ﬁ ne-setting

in phase cut-on

Load ﬂ ashes 3 x after

approx. 30 s and changes

to normal operation

Energy-saving lamps are switched on at a

brightness level of at least 50% in order to

ensure an ignition process.

4 x 230 V LED lamp

universal setting

in phase cut-on

or phase cut-oﬀ

Load ﬂ ashes 4 x after

approx. 5 s and changes

to normal operation

For connected dimmable 230 V LED lamps the

dimming principle and the optimal switch-on

brightness level is set automatically.

For all setting

modes

Load ﬂ ashes 5 x The selected setting mode is not supported by

the insert.

Table 4b

Operation

Operating concept

The operation of the top or bottom push-button op-

eration area is validated diﬀ erently for each button.

Simultaneous pressing of top and bottom push-but-

ton operation areas triggers special functions.

Settings

Setting the load

If the switching/dimming of the universal inserts is

not as desired after

commissioning the load may need to be re-set.



A load setting is required each time the load is

changed.

Switch oﬀ load.

Press button top and bottom area simultaneously

for more than 10 seconds.

The connected load ﬂ ashes once. The device is

in selection mode.



If no further actions are performed within the next

10 seconds, the dimmer switches to normal oper-

ation.

Brieﬂ y press the bottom button repeatedly to

activate the desired setting mode.

► See Table 4a / 4b



Information for electricians:

For the version labelling of the ﬂ ush-mounted

insert, see packaging label or sticker on the back

of the housing.

Operation on a power supply for KNX radio

application module

The push-buttons are freely conﬁ gurable; operation

is dependent on the conﬁ guration (Table 7).

Produkt Specifikationer

Mærke:	Hager
Kategori:	Ikke kategoriseret
Model:	85648188

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager 85648188 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Hager Manualer

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

EOTech EXPS3 Manual

26 December 2024

Schwinn 430 Manual

26 December 2024

Mount-It! MI-SB52 Manual

26 December 2024

Taga Harmony GTCS-606-6R SE Manual

26 December 2024

Taga Harmony TA-600multi Manual

26 December 2024

Taga Harmony TA-900multi Manual

26 December 2024

Taga Harmony TCW-100R v.3 Manual

26 December 2024

Taga Harmony TCW-180R Manual

26 December 2024

Taga Harmony TCW-380R Manual

26 December 2024

Taga Harmony TCW-600R v.2 Manual

26 December 2024