Hazebase Piccola Manual
Hazebase
Effekt maskine
Piccola
Læs nedenfor 📖 manual på dansk for Hazebase Piccola (21 sider) i kategorien Effekt maskine. Denne guide var nyttig for 18 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/21
Manual
pi olacc
Table of content
1. Preface 3
2. Safety 4
3. Name of the parts 5
4. Preparation 7
4.1 Selecting the location 7
4.2 Filling the tank 7
4.3 Hose cover 7
5. Working with the Piccola 8
5.1 Display of the Piccola 8
instructions5.2 Operation in stand-alone mode 8
5.3 mode selection in the 5 pin XLR connectors 9
5.4 operation DMX / RDM 10
5.5 operating cable remote control (optional) 10
5.5 operating by radio remote control (optional) 10
5.6 off the Piccola 11
6. the battery pack 12
6.1 change the battery pack 12
6.2 treatment of Battery packs 12
6.3 Charging the battery pack 13
6.4 Safety instructions for the battery pack 13
7. Vaporizer 13
7.1 Changing the vaporizer 13
8. Care and maintenance 15
9. Troubleshooting 16
10. Technical data en 17
11. Guarantee 18
2
pi olacc
2. Safety
instructions Very hot steam comes out of the mist outlet opening. Caution,
risk of burns!
During the fogging process, very hot fluid droplets can occasionally emerge
from the fog outlet opening. For this reason, no people or heat-sensitive
objects may be located within 1.5 m of the fog outlet.
Never tamper with the mist outlet opening during operation or when it is
activated.
The device must be set up in a location that is not sensitive to heat.
Maintain a minimum distance of 60 cm to inflammable, combustible and
heat-sensitive objects.
The fog fluid used contains a glycol, which burns with a slightly bluish,
almost invisible flame. Therefore, never smoke into strong ignition sources
such as open fire.
Never open the device connected to a power source.
Occasional leakage of hot fluid droplets is possible during operation. Care
should therefore be taken to ensure that these cannot become a danger to
people. Maintain a safety distance of 3m from the fog outlet nozzle.
Do not ingest the fog fluid and keep it away from children. In the event of
contact with the eyes, rinse with plenty of water. Consult a doctor in case of
accidental ingestion.
Spilled or splashed fluid can create a slip hazard. Collect fluid and dispose of
according to regulations.
Do not let the visibility drop below 2m, you are responsible for people who
move in the foggy room.
The generated fog can trigger smoke alarms.
The method used here to generate artificial fog is largely harmless and is used
worldwide in the entertainment sector. We are not aware of any case in which a
healthy person was harmed by the use of this artificial mist. Nevertheless, we
recommend sick people or people with previous respiratory tract damage or
a tendency to allergies to contact with artificial fog avoid!
4
pi olacc
3. Designation of the parts
Front
Rear view
5
pi olacc
Top view
battery pack
6
pi olacc
4. Preparation
4.1 Selecting the location
The location at which the Pi ola is operated must cc
●have good ventilation behave
●free of vibrations and shocks
●a non-flammable surface that is
●far enough away from easily flammable objects be away have
●an ambient temperature between 5 ° C and 45 ° C
4.2 Filling the tank
1. If necessary, remove the two XLR plugs
2. Push the sleeve of the quick coupling (6) in the direction of the tank. The
plug-in socket (7) is then unlocked and can be removed from the quick
coupling.
3. Remove holder.
4. Unscrew the tank from the tank cap and fill it with original Base B fluid.
Make sure that no dirt gets into the tank. The suction strainer may have to
be cleaned.
5. Slide the tank back into the tank holder.
6. Insert the plug-in socket (7) back into the quick coupling (6). When this
locks, a distinct "click" sound be heard.
4.3 Hose
The Pi ola is supplied with a hose cover for 15mm hoses. Please only use hoses that cc
can handle the temperatures. The hose cover is held by a magnet on the device. The
protruding ring on the hose cover is used for centering. This fits exactly into the mist
exit hole on the device.
The longer the mist duration is through the hose, the hotter the hose and the quality
of the mist decreases (becomes increasingly grayish). Small ventilation holes in the
hose directly on the hose cover can help improve this effect. Nevertheless,
condensation inevitably forms in the hose, which must be removed after each use.
7
pi olacc
5. Working with the Pi ola cc
The Pi ola is a battery-operated smoke machine with a directly heated evaporator. It cc
can generate the smallest clouds of fog to locate leaks, but it can also emit a larger,
effective fog cloud. The amount of mist can be set from 25% to 100% in 25% steps.
A single shot mode is also implemented.
5.1 Display of the Pi ola cc
The operation of the Pi ola takes place via the three buttons (minus / left, plus / cc
right, enter) and the OLED display. In the upper part of the display, the charge status
of the battery can be read on the left. The selected amount of fog is displayed in the
upper right part. The selected menu item is displayed in the middle. The respective
values are shown in the lower part of the display.
If a menu item is selected (see "Pump" above), the respective value can be changed
with the Minus / Left (9) and Plus / Right (10) buttons. The menu item can be
reached or exited with the Enter (11) key.
The Pi ola is switched on using the release button (1) or one of the other three cc
buttons (9-11).
5.2 Operation in stand-alone mode
The simplest control case is stand-alone mode. This can be started with the release
button (1).
8
pi olacc
If the trigger button (1) has been used, the fogging process starts immediately,
according to the preset amount of fog. As soon as the trigger button is released, the
reheating process begins to empty the evaporator tube. After 10 seconds the Pi ola cc
is switched off again and therefore no longer uses any electricity.
The following display appears in this stand-alone mode
. No menu item has yet been selected. You can now switch
through the menu with the minus / left (9) and plus / right
(10) buttons. The menu sequence is
Pump
→
Mode
→
Info.
Use the Enter (11) key to switch to the menu item Pump setting. The following
settings can now be made here:
single 25% 50% 75% 100%.→→→→
With the setting
single-shot,
only three pump blows are generated. This creates a
small burst of fog. To generate a second burst of fog, the release button must be
released and then pressed again. Leak tests can be carried out with this mode.
5.3 Mode selection of
the 5-pin XLR socket The next menu item is the setting of the mode for the 5-pin XLR
socket. When changing to this menu item, the following options are available:
Manual
→ → DMX Remote.
The socket is deactivated in manual mode. The device can only be using started the
trigger button.
In
DMX
mode, the socket is used to receive a DMX-512 telegram. Furthermore, the
Pi ola iscc
RDM
capable, so the DMX address can also be using an
RDM
changed
capable lighting console. A firmware update via
RDM is also
possible.
In
remote
mode, the Pi ola can be using triggered wired remote control or a radio cc
remote control.
If a mode other than manual is selected, the main menu is expanded to include the
corresponding sub-items.
9
pi olacc
5.4 Operation via DMX / RDM
The menu item DMX has now been added to the main
menu. By selecting this menu item you get to the setting of
the DMX address.
This can be changed using DMX address the minus button
(9) and plus button (10). The address is automatically
adopted after two seconds. This is indicated by flashing the
address .
If a valid DMX signal is received, a small "R" appears above
the quantity display.
Since the Piccola needs energy from the battery for DMX reception, in this case it
switches off one hour after the last valid DMX signal. This saves the battery.
5.5 Operation via cable(option)
The remote control “Remote” menu item has now been
added to the main menu. Selecting this menu item takes
you to the settings for the connected remote control. If a
remote control has not yet been connected, “no remote
found” appears in the display. As soon as a cable remote
control is connected, however, an "analog found" appears.
If a valid signal is received, a small "R" appears above the
quantity display. If the potentiometer on the remote control
is turned over 10% and the switch is switched on, the
fogging process is started. The output can now be 25%. 50%, 75% and 100% can be
set.
5.5 Operation via radio remote control (option)
If a radio remote control is connected, "radio found"
appears in the display. The fogging process can be
triggered by pressing the appropriately programmed button
on the hand transmitter. The pump value is adopted from
the setting on the device.
When using a radio remote control, several hand-held
transmitters can be trained on the receiver. A selection of
10
pi olacc
5.7 Machine
information In the “Info” menu item, the serial number and
the firmware version of the Pi ola can be read. cc
6. The battery pack
The supplied battery pack contains a maintenance-free 12V lead-gel battery. This can
be used independently of the location. The Pi ola is connected via a 4-pin. XLR cc
connector. The charger is connected via a low voltage socket.
When used properly, the battery retains its capacity for several years and has several
hundred charge / discharge cycles.
6.1 Changing the battery pack
To change the battery pack, first disconnect the battery from the device (4-pin XLR
plug). Then disconnect the hose connection to the tank and remove the tank from the
battery pack.
Now loosen the two knurled screws (3) and remove the device from the battery pack.
Mount the new battery pack in reverse order.
6.2 Handling the battery pack
The lead gel battery is a robust energy storage device that requires little care and
maintenance. Nevertheless, incorrect use and storage can greatly reduce the service
life.
Therefore: Never discharged battery store!
As a result, the battery can lose a large part of its capacity within a few weeks. If the
battery is stored for a longer period, it must be recharged regularly (at least every 6
months).
For safety reasons, always disconnect the battery from the device during
transport.
12
Produkt Specifikationer
| Mærke: | Hazebase |
| Kategori: | Effekt maskine |
| Model: | Piccola |
Har du brug for hjælp?
Hvis du har brug for hjælp til Hazebase Piccola stil et spørgsmål nedenfor, og andre brugere vil svare dig
Effekt maskine Hazebase Manualer
27 August 2024
27 August 2024
27 August 2024
27 August 2024
21 Juli 2024
Effekt maskine Manualer
- Effekt maskine Qtx
- Effekt maskine Behringer
- Effekt maskine Pyle
- Effekt maskine American DJ
- Effekt maskine Adj
- Effekt maskine König
- Effekt maskine Max
- Effekt maskine Viking
- Effekt maskine BeamZ
- Effekt maskine NGS
- Effekt maskine Stairville
- Effekt maskine Elation
- Effekt maskine Velleman
- Effekt maskine HQ Power
- Effekt maskine Monacor
- Effekt maskine Midas
- Effekt maskine ColorKey
- Effekt maskine Antari
- Effekt maskine Martin
- Effekt maskine Valueline
- Effekt maskine Eurolite
- Effekt maskine Chauvet
- Effekt maskine Boss
- Effekt maskine Klark Teknik
- Effekt maskine Cameo
- Effekt maskine Showtec
- Effekt maskine Manta
- Effekt maskine Rosco
- Effekt maskine Valcom
- Effekt maskine Monoprice
- Effekt maskine Laserworld
- Effekt maskine Drawmer
- Effekt maskine JB Systems
- Effekt maskine Evo-Lite
- Effekt maskine Blizzard
- Effekt maskine IGS Audio
- Effekt maskine Sagitter
- Effekt maskine Doepfer
- Effekt maskine Fun Generation
- Effekt maskine Karma
- Effekt maskine Lotronic
- Effekt maskine IMG Stage Line
- Effekt maskine Lexicon
- Effekt maskine Futurelight
- Effekt maskine The Confetti Maker
- Effekt maskine Eliminator Lighting
- Effekt maskine BoomTone DJ
- Effekt maskine Lab Gruppen
- Effekt maskine TCM FX
- Effekt maskine Audibax
- Effekt maskine Magmatic
- Effekt maskine Technical Pro
- Effekt maskine Froggy's Fog
Nyeste Effekt maskine Manualer
27 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025