Hifonics BRUTUS BE35-500.4 Manual

Hifonics Modtager BRUTUS BE35-500.4

Læs nedenfor 📖 manual på dansk for Hifonics BRUTUS BE35-500.4 (2 sider) i kategorien Modtager. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model. Some models require
an external fuse.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplier.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
Connect the speaker cables to
the speaker output connectors.
Follow the diagram below
that best ts your speaker
conguration.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplier
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Speaker
Connections
Chassis Ground
Be prepared to disarm your vehicles alarm and
to enter your radio / source unit code.
Stereo
Installation
Before you start
Monoblock single woofer multiple woofersMonoblock
Bridged
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
7
6
8
11
12
104
Turn the LEVEL control completely
counter-clockwise to minimum.
Level Control
9
6V 0.2V
INPUT
LEVEL
Model Fuse Size Cable Size
BE35 -500.4
BE35 800.4
BE35 1200.1D
BE35 1700.1D
BE35 2100.1D
BE35 2500.1D
BE35 5000.5
2x25A ATC
2x35A ATC
1 x 80A Maxi
2 x 70A Maxi
External 200A
External 250A
External 100A
4ga
4ga
4ga
2ga
2ga
0ga
0ga


Produkt Specifikationer

Mærke: Hifonics
Kategori: Modtager
Model: BRUTUS BE35-500.4

Har du brug for hjælp?

Hvis du har brug for hjælp til Hifonics BRUTUS BE35-500.4 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Modtager Hifonics Manualer

Modtager Manualer

Nyeste Modtager Manualer

DAP-Audio

DAP-Audio TA-4.3400 Manual

21 December 2024
JBL

JBL Power P7520 Manual

20 December 2024
JBL

JBL Power P-2510 Manual

20 December 2024
Devialet

Devialet Astra Dual Manual

19 December 2024
Devialet

Devialet Astra Manual

19 December 2024
QSC

QSC PL236 Manual

19 December 2024
QSC

QSC PL218 Manual

19 December 2024
QSC

QSC PL224 Manual

19 December 2024
QSC

QSC PL230 Manual

19 December 2024