Hifonics ZEUS ZD-1950.1D Manual

Hifonics Receiver ZEUS ZD-1950.1D

Læs nedenfor 📖 manual på dansk for Hifonics ZEUS ZD-1950.1D (2 sider) i kategorien Receiver. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to the
coordinating RCA input number
that will match the speaker
outputs number.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplier
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Chassis Ground
Be prepared to disarm your vehicles alarm and
to enter your radio / source unit code.
Installation
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
7
6
8
11
12
4
POWER
High Level Input
- DC turn on
- Signal Sense turn on
Low Level Input
- REM turn on (Remote wire turn on)
Please check Hifonics.com/product-manuals
for the Auto-Sense Technical Guide.
Turn on Mode
9
Model Fuse Size Cable Size
4ga
2ga
Using spade terminals,connect
the speaker cables to the speaker
output connectors. Follow the
diagram below that best ts your
speaker conguration.
Speaker
Connections
Stereo
Monoblock Monoblock single woofer multiple woofers
Bridged
10
CH1 CH2
SPE AKE R SPE AKE R
REM
ON
DC
ON
SIGNAL
ON
MODE
NOTE - When using low level input and the RCAs are plugged into the amplier and the TURN ON
MODE is in the DC ON position, the amplier will NOT turn on. Please re-read QR document above
or hire a professional installer.
Ext ernal 80A
Ext ernal 35A
Ext ernal 60A
Ext ernal 60A
Ext ernal 100A
Ext ernal 100A
Ext ernal 125A
ZD-1350.1D
ZD-1250.2D
ZD-750.4D
ZD-1350. 4D
ZD-1750.5D
ZD-1950.1D
ZD-2550.1D
ZD-3350.1D External 175A


Produkt Specifikationer

Mærke: Hifonics
Kategori: Receiver
Model: ZEUS ZD-1950.1D

Har du brug for hjælp?

Hvis du har brug for hjælp til Hifonics ZEUS ZD-1950.1D stil et spørgsmål nedenfor, og andre brugere vil svare dig




Receiver Hifonics Manualer

Receiver Manualer

Nyeste Receiver Manualer

Onkyo

Onkyo TX-910 Manual

3 Oktober 2024
Cayin

Cayin M-11LS Manual

3 Oktober 2024
Cayin

Cayin M-845D Manual

3 Oktober 2024
Axton

Axton A894DSP Manual

2 Oktober 2024
Yamaha

Yamaha RX-D 485 Manual

2 Oktober 2024
Jensen

Jensen VX3518 Manual

2 Oktober 2024
Vonyx

Vonyx VDA500 Manual

2 Oktober 2024
McIntosh

McIntosh MC-225 Manual

1 Oktober 2024