Hifonics Brutus Elite BE40-1000.1D Manual

Hifonics Modtager Brutus Elite BE40-1000.1D

Læs nedenfor 📖 manual på dansk for Hifonics Brutus Elite BE40-1000.1D (1 sider) i kategorien Modtager. Denne guide var nyttig for 21 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to the
coordinating RCA input number
that will match the speaker
outputs number.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
5
7
6
8
11
12
4
High Level Input
- DC turn on
- Music Sense
Low Level Input
- REM turn on
(Remote wire turn on)
Please scan QR code below or go to
Hifonics.com/product-manuals for the
Auto-Sense Technical Guide.
Turn on Mode
9
Model Fuse Size Cable Size
4ga
0ga
Using spade terminals,connect
the speaker cables to the speaker
output connectors. Follow the
diagram below that best ts your
speaker conguration.
Speaker
Connections
Stereo
Monoblock single woofer multiple woofersMonoblock
Bridged
10
MUSIC SENSE
DC SENSE
REMOTE
TURN ON MODE
NOTE - When using low level input and the RCAs are plugged into the amplier and the TURN ON
MODE is in the DC ON position, the amplier will NOT turn on. Please re-read QR document above
or hire a professional installer.
BE40-1000.1D
BE40-1500.1D
BE40-2000.1D
BE40-3000.1D
BE40-1500.2D
BE40-1500.4D
BE40-2000.5D
2x60A
External 150A
External 200A
External 300A
External 150A
External 150A
External 200A
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Disconnect
Negative Battery
Terminal
Run Cables
Mount Amplier
Installation
1
2
3
CH1 CH2
CH1 CH2
Common System Setup
4ch - Full Range
4ch - Mixed Mono
Mono
5ch
CH1 CH2
2ch - Full Range


Produkt Specifikationer

Mærke: Hifonics
Kategori: Modtager
Model: Brutus Elite BE40-1000.1D

Har du brug for hjælp?

Hvis du har brug for hjælp til Hifonics Brutus Elite BE40-1000.1D stil et spørgsmål nedenfor, og andre brugere vil svare dig




Modtager Hifonics Manualer

Modtager Manualer

Nyeste Modtager Manualer

Pro-Ject

Pro-Ject Amp Box DS2 Manual

15 Oktober 2024
AKG

AKG HP12U Manual

15 Oktober 2024
Icom

Icom IC-M15 Manual

14 Oktober 2024
APart

APart SBR160 Manual

14 Oktober 2024
JL Audio

JL Audio VX600/6i Manual

12 Oktober 2024
Lab Gruppen

Lab Gruppen E 20:2 Manual

11 Oktober 2024
Lab Gruppen

Lab Gruppen IPX 4800 Manual

11 Oktober 2024
Lab Gruppen

Lab Gruppen E 40:2 Manual

11 Oktober 2024