Husqvarna Rider 318 Manual

Husqvarna Plæneklipper Rider 318

Læs nedenfor 📖 manual på dansk for Husqvarna Rider 318 (1 sider) i kategorien Plæneklipper. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
PACKAGING/DELIVERY INSPECTION
1. Visually inspect the product and its packaging for transportation damage and missing components.
TECHNICAL INSPECTION
2. Check, charge and connect the battery. Measure battery voltage (should be above 12.7V before delivery).
3. Check and fit the steering wheel, seat, hook for rear accessories and check and adjust the tyre pressure.
4. Install the cutting deck, adjust lift springs, adjust the cutting deck and the unit’s height setting.
5. Check the oil level in the engine and if necessary, fill up with recommended Husqvarna oil SAE 10W/40 to be able to start and test.
6. Check the oil level in the transmission(s) and fill up with recommended Husqvarna oil (SAE 10W/50 for AWD models and SAE 10W/40
for 2 WD models) if necessary.
7. Check the belt positions and belt tensioners.
8. Fill with enough fresh fuel to be able to start and to test the engine on different RPM speeds. Always recommend Husqvarna fuel for
best perfomance.
9. Check the lights and other electrical components.
10. Check for any leaks from the hydraulic and fuel system.
SAFETY INSPECTION
11. Verify that the machine does not move in neutral and check forward and reverse drive on different speeds. Check the brake function.
12. Check the blade engagement and safety switches on seat, lift and drive/brake pedal.
SERVICE & DELIVERY
13. Inform the customer of the correct starting/stopping procedure, other safety features and necessary personal protective equipment.
14. Inform the end customer about recommended maintenance and remind the customer to book a time for recommended
first service. (See maintenance plan in operator’s manual).
15. Register the product in the Husqvarna Product Registration System.
Important to inform customer:
16. Hand over the operator’s manual to the end customer and instruct the customer to read it before use.
17. The transmission guarantee is only valid if the synchronisation of the front and rear wheels has been checked and adjusted in
compliance with the service schedule. The system will be damaged if synchronisation is not carried out.
18. Inform about Bio Clip system and other accessories.
NOTE! In the event of shipping products containing batteries, the dealer is responsible to assure shipment of the
product in accordance with applicable rules and regulations.
The PDI document itself is not a proof of purchase. Make sure to keep the printed receipt (proof of purchase)
together with the PDI document. In case of future defects please contact the dealer from which the product was bought.
MODEL PNC SERIAL NUMBER
DEALER NAME
CUSTOMER SIGNATURE DATE
DATE
114 31 16-26
Completion of this Pre-Delivery Inspection is mandatory for the dealer to
ensure the product is ready to be used when given to the end customer.
Some models may be subject to optional Pre-Delivery Inspection.
See SELDIS Contract, Appendix D for further details.
Tick
below
PETROL RIDERS
PDI Checklist
Stamp


Produkt Specifikationer

Mærke: Husqvarna
Kategori: Plæneklipper
Model: Rider 318

Har du brug for hjælp?

Hvis du har brug for hjælp til Husqvarna Rider 318 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Plæneklipper Husqvarna Manualer

Plæneklipper Manualer

Nyeste Plæneklipper Manualer

Toro

Toro 21863 Manual

19 November 2024
Gardena

Gardena 400 C Manual

16 November 2024
DeWalt

DeWalt DCMWSP650 Manual

9 November 2024
DeWalt

DeWalt DCMWSP256 Manual

9 November 2024
DeWalt

DeWalt DCMWP600 Manual

8 November 2024
Texas

Texas CB8750 Manual

5 November 2024
Einhell

Einhell BG-PM 46 Manual

14 Oktober 2024
Einhell

Einhell GE-SC 35 Li Manual

13 Oktober 2024
Stihl

Stihl RMA 235 Manual

13 Oktober 2024